Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 1, Problem 1.76P
(a)
To determine
The temperature of inner surface.
(b)
To determine
The effects of k , h and emissivity on temperature of outer surface, heat flux through the wall and heat fluxes associated with radiation and convection.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The temperature of a cylindrical tank containing liquid nitrogen is -10 ° C. Tank diameter is 16 cm. The amount of heat lost by convection and radiation from the tank to the environment is 65.5 W / m. Calculate the temperature of the environment where the tank is located: h = 4.35 W / m2K, ∈ = 1.
A large steel plate having a thickness of L = 4 in, thermal conductivity of k= 7.2 Btu/h·ft. °F, and
an emissivity of ε = 0.7 is lying on the ground. The exposed surface of the plate at x = L is known
to exchange heat by convection with the ambient air at T∞ = 90°F with an average heat transfer
coefficient of h = 12 Btu/h·ft².°F as well as by radiation with the open sky with an equivalent sky
temperature of Tsky =480 R. Also, the temperature of the upper surface of the plate is measured
to be 80°F. Assuming steady one-dimensional heat transfer, (a) express the differential equation
and the boundary conditions for heat conduction through the plate, (b) obtain a relation for the
variation of temperature in the plate by solving the differential equation, and (c) determine the
value of the lower surface temperature of the plate at x = 0.
Tsky
h, To
Convection
Radiation
XA
80°F
L
E
Plate
0
Ground
The inside surface of an insulation layer is maintained at 350°C and the outside surface dissipates
heat by convection and radiation to air and wall, respectively. The temperatures of air and wall are 15 °C.
The insulation layer has a thickness of 10 cm and a thermal conductivity of 15 W/m.K. What is the value of
the heat transfer coefficient at the outside surface of the layer, if the temperature at the outside surface
should not exceed 225 °C? (The emissivity and the width of the surface are 0.3 and 1 m., respectively.
o=5.67x10-8 W/m²K*).
Tw=15°.
T=225°C
e=0.3
T=350°C
To=15°C
h,=?
10 cm
Chapter 1 Solutions
Introduction to Heat Transfer
Ch. 1 - The thermal conductivity of a sheet of rigid,...Ch. 1 - The heat flux that is applied to the left face of...Ch. 1 - A concrete wall, which has a surface area of 20m2...Ch. 1 - The concrete slab of a basement is 11 m long, 8 m...Ch. 1 - Consider Figure 1.3. The heat flux in the...Ch. 1 - Prob. 1.6PCh. 1 - The inner and outer surface temperatures of a...Ch. 1 - A thermodynamic analysis of a proposed Brayton...Ch. 1 - A glass window of width W=1m and height H=2m is 5...Ch. 1 - Prob. 1.10P
Ch. 1 - The heat flux that is applied to one face of a...Ch. 1 - Prob. 1.12PCh. 1 - Prob. 1.13PCh. 1 - Prob. 1.14PCh. 1 - The 5-mm-thick bottom of a 200-mm-diameter pan may...Ch. 1 - Prob. 1.16PCh. 1 - For a boiling process such as shown in Figure...Ch. 1 - You've experienced convection cooling if you've...Ch. 1 - Prob. 1.19PCh. 1 - A wall has inner and outer surface temperatures of...Ch. 1 - An electric resistance heater is embedded in a...Ch. 1 - Prob. 1.22PCh. 1 - A transmission case measures W=0.30m on a side and...Ch. 1 - Prob. 1.24PCh. 1 - A common procedure for measuring the velocity of...Ch. 1 - Prob. 1.26PCh. 1 - Prob. 1.27PCh. 1 - Prob. 1.28PCh. 1 - Prob. 1.29PCh. 1 - Prob. 1.30PCh. 1 - Prob. 1.31PCh. 1 - Prob. 1.32PCh. 1 - Prob. 1.33PCh. 1 - Prob. 1.34PCh. 1 - An electrical resistor is connected to a battery,...Ch. 1 - Pressurized water pin=10bar,Tin=110C enters the...Ch. 1 - Consider the tube and inlet conditions of Problem...Ch. 1 - An internally reversible refrigerator has a...Ch. 1 - A household refrigerator operates with cold- and...Ch. 1 - Chips of width L=15mm on a side are mounted to a...Ch. 1 - Consider the transmission case of Problem 1.23,...Ch. 1 - One method for growing thin silicon sheets for...Ch. 1 - Heat is transferred by radiation and convection...Ch. 1 - Radioactive wastes are packed in a long,...Ch. 1 - An aluminum plate 4 mm thick is mounted in a...Ch. 1 - A blood warmer is to be used during the...Ch. 1 - Consider a carton of milk that is refrigerated at...Ch. 1 - The energy consumption associated with a home...Ch. 1 - Liquid oxygen, which hems a boiling point of 90 K...Ch. 1 - The emissivity of galvanized steel sheet, a common...Ch. 1 - Three electric resistance heaters of length...Ch. 1 - A hair dryer may be idealized as a circular duct...Ch. 1 - In one stage of an annealing process, 304...Ch. 1 - Convection ovens operate on the principle of...Ch. 1 - Annealing, an important step in semiconductor...Ch. 1 - In the thermal processing of semiconductor...Ch. 1 - A furnace for processing semiconductor materials...Ch. 1 - Single fuel cells such as the one of Example 1.5...Ch. 1 - Prob. 1.59PCh. 1 - Prob. 1.60PCh. 1 - Prob. 1.61PCh. 1 - A small sphere of reference-grade iron with a...Ch. 1 - A 50mm45mm20mm cell phone charger has a surface...Ch. 1 - A spherical, stainless steel (AISI 302) canister...Ch. 1 - Prob. 1.65PCh. 1 - Prob. 1.66PCh. 1 - A photovoltaic panel of dimension 2m4m is...Ch. 1 - Following the hot vacuum forming of a paper-pulp...Ch. 1 - Prob. 1.69PCh. 1 - Prob. 1.70PCh. 1 - Prob. 1.71PCh. 1 - The roof of a car in a parking lot absorbs a solar...Ch. 1 - Prob. 1.73PCh. 1 - Prob. 1.74PCh. 1 - Consider Problem 1.1. If the exposed cold surface...Ch. 1 - Prob. 1.76PCh. 1 - Prob. 1.77PCh. 1 - A thin electrical heating element provides a...Ch. 1 - Prob. 1.79PCh. 1 - Prob. 1.80PCh. 1 - Prob. 1.81PCh. 1 - The curing process of Example 1.9 involves...Ch. 1 - The diameter and surface emissivity of an...Ch. 1 - Bus bars proposed for use in a power transmission...Ch. 1 - A solar flux of 700W/m2 is incident on a...Ch. 1 - In considering the following problems involving...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A wall in a house contains a single window. The window consists of a single pane of glass whose area is 0.13 m2 and whose thickness is 8 mm. Treat the wall as a slab of the insulating material Styrofoam whose area and thickness are 19 m2 and 0.10 m, respectively. Heat is lost via conduction through the wall and the window. The temperature difference between the inside and outside is the same for the wall and the window. Of the total heat lost by the wall and the window, what is the percentage lost by the window?arrow_forwardThe furnace wall shown in the figure is made of a material with a thermal conductivity of 5 W / m ° C, the radiant emission coefficient of the outer surface of the wall is 0.95, Stefan Boltzman constant is 5.67x104 W / m ^ 2 (K ^ 4), ambient temperature and air temperature 297 K is. The heat transfer coefficient between the outer surface of the wall and the air is h = 20 W / m (K ^ 2). Wall inner surface temperature 573 K, outer surface temperature 308 K Since the value is kept constant a) Find the layer thickness of the wall? b) Find the layer thickness of the wall if the moving fluid medium on the outer surface of the wall is corroded?arrow_forwardThe car is outdoors in direct sunlight. The outside air temperature is 27 ° C. The temperature inside the car is maintained by air conditioning 22 ° C. What is the temperature of the outside surface of the car roof? The power density of solar radiation is 840 W / m2 and the absorption coefficient of the roof paint for radiation is 0.51. The heat transfer coefficient from the roof surface to the outside air is 11.6 W / (m2K), which also includes heat radiation from the surface to the environment. Radiation from the atmosphere to the car is not taken into account. The total thermal resistance of the car's roof structure is 1.0 m2K / W. The task does not look at any other part of the vehicle but only the roof. If you need an area, make a calculation per 1 m2.arrow_forward
- Consider steady heat transfer between two large parallel plates at constant temperatures of T1 = 500 K and T2 = 300 K that are L = 2.5 cm apart. The emissivity of the surfaces, ɛ = 0.95. Calculate the total rate of heat transfer and the percentage by thermal radiation between the plates per unit surface area assuming the gap between the plates is (a) filled with atmospheric air (k = 0.02 W/m.°C), (b) evacuated. %3D %3D %3D O = 5.67 x 10-8 W/m².K4arrow_forwardConsider a large plane wall of thickness L = 0.8 ft and thermal conductivity k = 1.2 Btu/h-ft-°F. The wall is covered with a material that has an emissivity of ε = 0.80 and a solar absorptivity of a = 0.60. The Inner surface of the wall is maintained at T₁ = 524 R at all times, while the outer surface is exposed to solar radiation that is incident at a rate of q solar = 300 Btu/h-ft2. The outer surface is also losing heat by radiation to deep space at O K. 0 Plate a solar o = 0.1714 x 10-8 Btu/h ft2 R4 Sun If the temperature of the outer surface of the wall is 556.39 R, determine the rate of heat transfer through the wall when steady operating conditions are reached. (Round your answer up to 2 decimal places.) 51 Btu/h-ft2 (per The rate of heat transfer through the wall when steady operating conditions are reached unit area)arrow_forwardCalculate the heat transfer between two (50*40 cm) parallel plates at constant temperatures of 71 = 100 K and 72 = 50 K that are L = 1 cm apart, assuming the emissivity (r) is 0.6 according to the following conditions. 1. The parallel plates filled with atmospheric air assume the thermal conductivity at the average temperature of 250 K is k=0.021 Heat direction Air Space * 24140 Heat direction Super-insulation W/m °C for air, Stefan-Boltzmann constant is 5.67*10*W/m².K' 2. The parallel plates are filled with super-insulated material and have an apparent thermal conductivity of 0.00004 W/m - °C.arrow_forward
- Consider the rate of heat conduction through a double-paned window that has a 1.6-m2 area and is made of two panes of 0.76-cm-thick glass separated by a 0.75-cm air gap. You can ignore the increased heat transfer in the air gap due to convection. a. Calculate the rate of heat conduction through this window, in watts, given that the inside surface temperature is 15.0°C, while the outside temperature is -10.0°C. Make the assumption that the temperature differences across the two glass planes are equal. First find these and then the temperature drop across the air gap. b. For comparison, calculate the rate of heat conduction, in watts, through a single 1.67-cm-thick window of the same area and with the same temperatures as in part (a).arrow_forwardA thermometric well is placed in a pipe having diameter of 55 mm. Pipe wall temperature is 100°C and heat transfer coefficient inside the pipe is 300 W/m² K. Thickness of thermowell is 1.2 mm and its length is 50 mm. Thermal conductivity of thermowell material. Is 30 W/mK. If the temperature of the gas flowing through the pipe is recorded by thermometer as 200°C, determine the true temperature of gas. If the error in gas temperature is to be reduced by 80% by increasing the length of thermowell, determine the new length of thermowell. Draw a sketch of this thermowell. Take perimeter to area ratio for thermowell as 1/T (T= thickness).arrow_forwardA furnace wall comprises three layers of thickness 250 mm, 100 mm, and 150 mm with thermal conductivities of 1.65, k and 9.2 W/m K respectively. The inside is exposed to gases at 1250 °C with convection of 25 W/m2K, and the inside surface is at 1100 °C, the outside surface air at 25 °C with convection of 12 W/m2K. Determine the temperatures of the outer surface in degree celcius to 1 d.p.?arrow_forward
- It is designed in such a way that the internal temperature of a commercial heat treatment furnace can reach up to 165 oC. All surfaces of the furnace consist of firebrick (10 cm), insulation material and sheet metal (3mm) from the inside out. Given that the outdoor temperature is 22 oC, the outer sheet will be allowed to go up to 35 oC, which is a temperature that will not be disturbed by hand contact. In this case, determine the insulation material thickness to be used. Insulation material thermal conductivity coefficient is 0.066 insulation W / m oC, 60 W / m oC for sheet metal and 115 W / m oC for firebrick. Indoor heat transfer coefficient will be accepted as 25 W / m2 oC and 12 W / m2 oC for outdoor environment.arrow_forwardIn a textile unit, hot fluid flows through a long steel pipe (k=15 W/m°C) with inner and outer diameters of 70 mm and 75 mm, respectively. The convection coefficient between the hot fluid and the inner surface of the pipe is 100 W/m²K, the convection coefficient between the outer surface of the pipe and the ambient air is 10 W/m²K, and the emissivity (emission) coefficient of the pipe is 0,75. Under steady regime conditions; Since the pipe outer surface temperature is 80°C, the outside air and ambient temperature is 20°C,a) The total amount of heat lost to the environment per unit length of the pipe,b) Calculate the hot fluid temperature and the pipe inner surface temperature.arrow_forwardConsider a long horizontal pipe with a diameter of 90 mm and emissivity of 0.8 transfers steam at 227°C. Outside of the pipe is air at 27°C and the surroundings of the pipe are also at 27°C. You may assume the temperature of the pipe wall is the same as the temperature of the steam. 1. Find the heat loss per unit length (W/m) for the pipe when the air outside is still. 2. Find the heat loss per unit length (W/m) for the pipe when the wind outside is 8 m/s and blows perpendicularly across the pipe.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license