It is designed in such a way that the internal temperature of a commercial heat treatment furnace can reach up to 165 oC. All surfaces of the furnace consist of firebrick (10 cm), insulation material and sheet metal (3mm) from the inside out. Given that the outdoor temperature is 22 oC, the outer sheet will be allowed to go up to 35 oC, which is a temperature that will not be disturbed by hand contact. In this case, determine the insulation material thickness to be used. Insulation material thermal conductivity coefficient is 0.066 insulation W / m oC, 60 W / m oC for sheet metal and 115 W / m oC for firebrick. Indoor heat transfer coefficient will be accepted as 25 W / m2 oC and 12 W / m2 oC for outdoor environment.

It is designed in such a way that the internal temperature of a commercial heat treatment furnace can reach up to 165 oC. All surfaces of the furnace consist of firebrick (10 cm), insulation material and sheet metal (3mm) from the inside out. Given that the outdoor temperature is 22 oC, the outer sheet will be allowed to go up to 35 oC, which is a temperature that will not be disturbed by hand contact. In this case, determine the insulation material thickness to be used. Insulation material thermal conductivity coefficient is 0.066 insulation W / m oC, 60 W / m oC for sheet metal and 115 W / m oC for firebrick. Indoor heat transfer coefficient will be accepted as 25 W / m2 oC and 12 W / m2 oC for outdoor environment.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.24P

See similar textbooks

Similar questions

As a designer working for a major electric appliance manufacturer, you are required to estimate the amount of fiberglass insulation packing (k = 0.035 W/m K) that is needed for a kitchen oven shown in the figure below. The fiberglass layer is to be sandwiched between a 2-mm-thick aluminum cladding plate on the outside and a 5-mm-thick stainless steel plate on the inside that forms the core of the oven. The insulation thickness is such that the outside cladding temperature does not exceed 40C when the temperature at the inside surface of the oven is 300C. Also, the air temperature in the kitchen varies from 15Cto33C, and the average heat transfer coefficient between the outer surface of the oven and air is estimated to be 12.0W/m2K. Determine the thickness of the fiberglass insulation that is required for these conditions. What would be the outer surface temperature when the inside surface of the oven is at 475C?
2.30 An electrical heater capable of generating 10,000 W is to be designed. The heating element is to be a stainless steel wire having an electrical resistivity of ohm-centimeter. The operating temperature of the stainless steel is to be no more than 1260°C. The heat transfer coefficient at the outer surface is expected to be no less than in a medium whose maximum temperature is 93°C. A transformer capable of delivering current at 9 and 12 V is available. Determine a suitable size for the wire, the current required, and discuss what effect a reduction in the heat transfer coefficient would have. (Hint: Demonstrate first that the temperature drop between the center and the surface of the wire is independent of the wire diameter, and determine its value.)
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
2.55 A long, 1-cm-diameter electric copper cable is embedded in the center of a 25-cm-square concrete block. If the outside temperature of the concrete is 25oC and the rate of electrical energy dissipation in the cable is 150 W per meter length, determine temperatures at the outer surface and at the center of the cable.
It is designed in such a way that the internal temperature of a commercial heat treatment furnace can reach up to 165 oC. All surfaces of the furnace consist of firebrick (10 cm), insulation material and sheet metal (3mm) from the inside out. Given that the outdoor temperature is 22 oC, the outer sheet will be allowed to go up to 35 oC, which is a temperature that will not disturb in contact with hands. In this case, determine the insulation material thickness to be used. The thermal conductivity coefficient of the insulation material is insulation 0.066 W / m oC, 60 W / m oC for sheet metal and 115 W / m oC for firebrick. Indoor heat transfer coefficient will be accepted as 25 W / m2 oC and 12 W / m2 oC for outdoor environment.
The temperature at the inner and outer surfaces of a boiler wall made of 25 mm thick steel and covered with an insulating material of10 mm thickness are 300 C and 50C respectively. If the thermal conductivities of steel and insulating material are 58W/mC and 0.116W/mC respectively, determine the total resistance through the boiler wall. (Note area of sample boiler wall is 8 m2)
A metal furnace with a 1.25 m x 0.75 m metal door is placed in a room and set to 400K. A 0.3 m x 0.3 m glass window is located in the furnace door. The thickness of the metal alloy and the glass window are 3 mm and 2 mm, respectively. The glass window has a thermal conductivity (k) of 0.7 W/m .K and the metal door has a thermal conductivity (k) of 3.5 W/m.K. The convective heat coefficient hi and ho on each site of the furnace door is estimated as 10W/m2.K. Assuming the room temperature is held constant at 297 K, calculate the total heat loss from the furnace door. P.S Could you write the solution clearly to better understanding? Step by step using formulas. Another page with detailed steps would be better. Thanks in advance.
In an electrically heated home, the temperature of the ground in contact with a concrete basement wall is 13.8 oC. The temperature at the inside surface of the wall is 18.4 oC. The wall is 0.13 m thick and has an area of 6.8 m2. Assume that one kilowatt hour of electrical energy costs $0.10. How many hours are required for one dollar's worth of energy to be conducted through the wall?
2. A refrigerated cold room wall has a thickness of 100mm and a thermal conductivity 0.14 W/m-K. The room wall has a 60mm thick internal lining of cork having a thermal conductivity of 0.05 W/m.K. The thermal conductance between the exposed faces and the respective atmosphere is 12 W/m²-K. If the room is maintained at 0°C and the external atmospheric temperature is 20°C, Calculate the heat loss rate through 1m² of the wall.
3-28E A wall is constructed of two layers of 0.6-in-thick sheetrock (k = 0.10 Btu/h-ft-°F), which is a plasterboard made of two layers of heavy paper separated by a layer of gypsum, placed 7 in apart. The space between the sheetrocks is filled with fiberglass insulation (k = 0.020 Btu/h-ft F). Determine (a) the thermal resistance of the wall and (b) its R-value of insulation in English units. FIGURE P3-28E Fiberglass insulation Sheetrock 0.6 in 7 in I 0.6 in
20-m pipe has an outside diameter of 50 mm. Pipe is insulated with a layer of asbestos, then followed by a layer of cork. Inside and outside diameter of the cork is 77 mm and 80 mm, respectively. If the temperature drop from pipe to cork is 1165°C, calculate the inside diameter of the pipe (mm). The rate of the heat transfer is 8778 W. The thermal conductivity of steam pipe, asbestos and cork are 0.045 kW/m-K, 0.058 W/m-K and 0.043 W/m-K respectively.
5. A pipe with an outside diameter of 2.5 inches is insulated with 2 inches layer of asbestos (k = 0.396 Btu- in/hr-ft²-°F), followed by a layer of cork 1.5 inches thick (k = 0.30 Btu-in/hr-ft²-°F). If the temperature at the inner surface of the pipe is 290°F and at the outer surface of the cork is 90°F, calculate the heat loss per 100 ft of insulated pipe. (Btu/hr)