Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
10th Edition
ISBN: 9780073398204
Author: Richard G Budynas, Keith J Nisbett
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 8, Problem 49P
(a)
To determine
The yielding factor of safety.
(b)
To determine
The factor of safety for overload.
(c)
To determine
The factor of safety for joint separation.
(d)
To determine
The fatigue factor of safety using Goodman criteria.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
For a bolted assembly with six bolts, the stiffness of each bolt is kb = 2.8 Mlbf/in and the stiffness of the members is km=
14 Mlbf/in per bolt. An external load of 80 kips is applied to the entire joint. Assume the load is equally distributed to all the
bolts. It has been determined to use 1/2 in-13 UNC grade 8 bolts with rolled threads. Assume the bolts are preloaded to 75
percent of the proof load.
Determine the yielding factor of safety.
The yielding factor of safety is
4. Determine the design stress for bolts in a cylinder cover where the load is fluctuating due to gas
pressure. The maximum load on the bolt is 50 kN and the minimum is 30 kN. The load is unpredict-
able and factor of safety is 3. The surface of the bolt is hot rolled and the suface finish factor is 0.9.
During a simple tension test and rotating beam test on ductile materials (40 C 8 steel annealed), the
following results were obtained :
Diameter of specimen =12.5 mm; Yield strength= 240 MPa; Ultimate strength= 450 MPa; Endurance
limit = 180 MPa.
[Ans. 65.4 MPa]
3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint
is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade,
with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length
for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the
elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply
the preload. Assume that coefficients of friction between the bolt, nut, and collar are all ~0.15. For
steel, use E = 207 GPa.
Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain
washers are provided in the textbook appendices.
Chapter 8 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Ch. 8 - A power screw is 25 mm in diameter and has a...Ch. 8 - Using the information in the footnote of Table...Ch. 8 - Show that for zero collar friction the efficiency...Ch. 8 - A single-threaded power screw is 25 mm in diameter...Ch. 8 - The machine shown in the figure can be used for a...Ch. 8 - The press shown for Prob. 8-5 has a rated load of...Ch. 8 - For the screw clamp shown, a force is applied at...Ch. 8 - The C clamp shown in the figure for Prob. 8-7 uses...Ch. 8 - Find the power required to drive a 1.5-in power...Ch. 8 - A single square-thread power screw has an input...
Ch. 8 - Prob. 11PCh. 8 - An M14 2 hex-head bolt with a nut is used to...Ch. 8 - Prob. 13PCh. 8 - A 2-in steel plate and a 1-in cast-iron plate are...Ch. 8 - Repeat Prob. 8-14 with the addition of one 12 N...Ch. 8 - A 2-in steel plate and a 1-in cast-iron plate are...Ch. 8 - Two identical aluminum plates are each 2 in thick,...Ch. 8 - Prob. 18PCh. 8 - A 30-mm thick AISI 1020 steel plate is sandwiched...Ch. 8 - Prob. 20PCh. 8 - Prob. 21PCh. 8 - Prob. 22PCh. 8 - A 2-in steel plate and a 1-in cast-iron plate are...Ch. 8 - An aluminum bracket with a 12-in thick flange is...Ch. 8 - An M14 2 hex-head bolt with a nut is used to...Ch. 8 - A 34 in-16 UNF series SAE grade 5 bolt has a 34-in...Ch. 8 - From your experience with Prob. 8-26, generalize...Ch. 8 - Prob. 28PCh. 8 - Prob. 29PCh. 8 - Prob. 30PCh. 8 - For a bolted assembly with eight bolts, the...Ch. 8 - Prob. 32PCh. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - Prob. 37PCh. 8 - Prob. 38PCh. 8 - 837 to 840 Repeat the requirements for the problem...Ch. 8 - Prob. 40PCh. 8 - 841 to 844 For the pressure vessel defined in the...Ch. 8 - Prob. 42PCh. 8 - Prob. 43PCh. 8 - Prob. 44PCh. 8 - Bolts distributed about a bolt circle are often...Ch. 8 - The figure shows a cast-iron bearing block that is...Ch. 8 - Prob. 47PCh. 8 - Prob. 48PCh. 8 - Prob. 49PCh. 8 - Prob. 50PCh. 8 - 851 to 854 For the pressure cylinder defined in...Ch. 8 - Prob. 52PCh. 8 - 851 to 854 For the pressure cylinder defined in...Ch. 8 - 851 to 854 For the pressure cylinder defined in...Ch. 8 - 855 to 858 For the pressure cylinder defined in...Ch. 8 - 855 to 858 For the pressure cylinder defined in...Ch. 8 - 855 to 858 For the pressure cylinder defined in...Ch. 8 - For the pressure cylinder defined in the problem...Ch. 8 - A 1-in-diameter hot-rolled AISI 1144 steel rod is...Ch. 8 - The section of the sealed joint shown in the...Ch. 8 - Prob. 61PCh. 8 - Prob. 62PCh. 8 - Prob. 63PCh. 8 - Prob. 64PCh. 8 - Using the Goodman fatigue criterion, repeat Prob....Ch. 8 - The figure shows a bolted lap joint that uses SAE...Ch. 8 - Prob. 67PCh. 8 - A bolted lap joint using ISO class 5.8 bolts and...Ch. 8 - Prob. 69PCh. 8 - The figure shows a connection that employs three...Ch. 8 - A beam is made up by bolting together two cold...Ch. 8 - Prob. 72PCh. 8 - Prob. 73PCh. 8 - Prob. 74PCh. 8 - A vertical channel 152 76 (see Table A7) has a...Ch. 8 - The cantilever bracket is bolted to a column with...Ch. 8 - Prob. 77PCh. 8 - The figure shows a welded fitting which has been...Ch. 8 - Prob. 79PCh. 8 - Prob. 80PCh. 8 - Prob. 81P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Problem 3: A Hexagonal bolt connects two members. The joint has a gap 1 = 2 in and the applied load is 2000 lb. Both of the clamped parts are steel. A preload of 90% the bolt's proof strength will be applied first. For this design, an SAE grade 1, 5/16"-18 UNC-2A bolt is chosen made from A307 with rolled threads. Washers are included between the head and the joint, and between the nut and the joint. Determine a suitable length for the bolt? Find its safety factor against yielding and against joint separation. Are these values acceptable?arrow_forwardFor a bolted assembly with 8 bolts, the stiffness of each bolt is k_b = 1.1 N/mm and the stiffness of the members is k_m = 2.8 N/mm at each bolt location. The joint is subject to occasional disassembly for maintenance and should be preloaded accordingly (to 75% of the proof stress). Assume the external load is equally distributed to all the bolts. It has been determined to use M6 × 1 class 5.8 bolts with rolled threads. Determine the maximum safe working load that both limits the stress in the bolts to be below the proof stress and ensures that the members do not come out of compression. Express your answer in units of kilonewtons.arrow_forward1. For a bolted assembly with six bolts, the stiffness of each bolt is k, = 3 Mlbf/in and the stiffness of the members is km = 12 Mlbf/in per bolt. An external load of 80 kips is applied to the entire joint. Assume the load is equally distributed to all the bolts. It has been determined to use 1/2 in-13 UNC grade 8 bolts with rolled threads. Assume a torque co-efficient of K = 0.2. a. Determine the maximum bolt preload that can be applied without exceeding the proof strength of the bolts. b. Determine the minimum bolt preload that can be applied while avoiding joint separation. c. Determine the value of torque in units of Ibf-ft that should be specified for preloading the bolts if it is desired to preload to 75% of the proof load. d. Determine the yielding factor of safety for part c). (based on proof strength)arrow_forward
- A 3-in Aluminum plate and a 2-in cast-iron plate are compressed with one bolt and nut. The bolt is 7/8 in-9 UNC. (1) Determine a suitable length for the bolt, rounded up to the nearest in. (2) Determine the bolt stiffness. (3) Determine the stiffness of the members.arrow_forwardTwo plates are clamped by a 3/4-10 UNC SAE Grade 5 bolt and regular nut with a 3/4-W plain washer as shown in figure. Top plate is made of grey cast iron and bottom plate is steel. An axial force of 12kN is acted upon the joint. Round off the length of the bolt to nearest 1/4in. Assume bolts are preloaded to 75% of proof load. 1. Determine the bolt stiffness kb. 2. Determine the member stiffness km. 3. Determine the yielding factor of safety of the bolt. 4. Determine the load factor for the bolt. 5. Determine the load factor guarding against joint separation. 1.25 in 1.00 inarrow_forwardThe figure shows a section of a large coupling. Each bolt in this joint is subjected to cyclic load fluctuating between 0 and 13 kN. The members are made from steel. The members have equal thicknesses and total length of members is L=37 mm. Each bolt is initially tightened carefully to 78% of proof load. The bolt is to be Metric grade 5.8 M12x1.75 (coarse-pitch series). The threads has been manufactured by rolling and reliability for bolts is 95%. Calculate the stiffness of the bolt (in kN/mm). Yanıt:arrow_forward
- M16 x 2.0 ISO 5.8 coarse series bolts and nuts clamp a 26-mm-thick steel cover plate to a 6-mm-thick steel flange. Steel washers (Size: 16R) are used under the head of the bolt and also under the nut . Assume E = 207 GPa- (a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness. (c) Determine the stiffness of the members. (d) Determine the stiffness of the joint.arrow_forwardA factor of safety of 2.5 is used for the bolts in the assembly below. The ultimate shear stress of the magnesium alloy bolts is 20.0ksi. What should be the diameter of the bolts? 10 kip 5 kip 5 kip Diameter = inarrow_forwardAn M 14 x 2 hex-head bolt with a nut and a 14R washer under each of bolt head and the nut is used to clamp together two 18-mm steel plates. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the bolt stiffness. The bolt stiffness kb is 592.69 MN/m.arrow_forward
- Calculate the maximum tensile stress developed in a 1/4-20 bolt (Major dia = 0.2500" and Root dia = 0.1959"), 3" long, and a head height of 0.1875", if it is subjected to a load of 426 lbs.arrow_forwardRequired information For a bolted assembly with six bolts, the stiffness of each bolt is kb 2 Mibf/in and the stiffness of the members is km = 13 Mlbf/in per bolt. An external load of 80 kips is applied to the entire joint. Assume the load is equally distributed to all the bolts. It has been determined to use 1/2 in-13 UNC grade 8 bolts with rolled threads. It is desired to find the range of torque that a mechanic could apply to initially preload the bolts without expecting failure once the joint is loaded. Assume a torque coefficient of K = 0.2. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the maximum bolt preload that can be applied without exceeding the proof strength of the bolts once the load is applied. The maximum bolt preload that can be applied is Ibf.arrow_forwardCondition #1: A structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook. Condition #2: The same structural support of the basic size determined in Condition 1 is subjected to a tensile load of 15 kN that is repeated several thousand times over the life of the machine. This load is not an addition to the 20 kN. Specify a suitable steel that is suitable to this application based on the basic size determined in Condition #1. Loading of Condition #1 does not apply here. Condition #3: The same structural support from Condition 2 is heated from room temperature of 25°C. The support is placed inside a frame on both ends. There is a total clearance of 0.2 mm between the support and its frame. Initial length of the rod is 200 mm. Specify the…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
How to Measure Threads; Author: PracticalMachinist;https://www.youtube.com/watch?v=Uuy7EViS7Kc;License: Standard Youtube License