Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470501979
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 2, Problem 2.43P
cylindrical system illustrated has negligible variation of temperature in the r- and z-directions. Assume that
- Beginning with a properly defined control volume and considering energy generation and storage effects, derive the differential equation that prescribe: the variation in temperature with the angular coordinate
- For conditions with no internal heat generation and constant properties, determine the temperature distribution
- For the conditions of part (b) write the expression for the heat rate
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
under steady-state conditions. If you are given T1 = 200 °C and T2 = 164 °C, determine:
a) the conduction heat flux, q,.cond, in
m2
W
from x = 0 to x = L
b) if the dimensions of the triangle ares 15 mm and h 13 mm, calculate the heat
transfer due to convection, q,y, in W at x = L
Finsulation
T2
T
T = 20°C
h = 500 W/m2.K
Triangular Prism
x L
x 0
L= 50 mm
k = 100 W/m-K
Q4/ A room on the second floor of a house with a balcony has a door. The door made
of teak (wood) and it contains a large sheet of glass (outside winter type) in the
middle and constitutes 80% of the area of the door. Door thickness is 40 mm and the
temperature in the room 25. °C when the temperature is in the balcony 8 °C. Calculate
the rate of heat loss from the room to the balcony through the door. The door
dimensions 2m x 1m. Assume Inside and outside still air thermal resistance f= 8.29
W/m2 °C and f. 34.1 W/m2 °C respectively
Q1
Passage of an electric current through a long conducting
rod of radius r; and thermal conductivity k, results in
uniform volumetric heating at a rate of ġ. The conduct-
ing rod is wrapped in an electrically nonconducting
cladding material of outer radius r, and thermal conduc-
tivity k, and convection cooling is provided by an
adjoining fluid.
Conducting
rod, ġ, k,
11
To
Čladding, ke
For steady-state conditions, write appropriate forms of
the heat equations for the rod and cladding. Express ap-
propriate boundary conditions for the solution of these
equations.
Chapter 2 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - Assume steady-state, one-dimensional conduction in...Ch. 2 - A hot water pipe with outside radius r, has a...Ch. 2 - A spherical shell with inner radius r1 and outer...Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - A composite rod consists of two different...Ch. 2 - A solid, truncated cone serves as a support for a...Ch. 2 - To determine the effect of the temperature...Ch. 2 - A young engineer is asked to design a thermal...Ch. 2 - A one-dimensional plane wall of thickness 2L=100mm...
Ch. 2 - Consider steady-state conditions for...Ch. 2 - Consider a plane wall 100 mm thick and of thermal...Ch. 2 - A cylinder of radius ro, length L, and thermal...Ch. 2 - In the two-dimensional body illustrated, the...Ch. 2 - Consider the geometry of Problem 2.14 for the case...Ch. 2 - Steady-state, one-dimensional conduction occurs in...Ch. 2 - An apparatus for measuring thermal conductivity...Ch. 2 - An engineer desires to measure the thermal...Ch. 2 - Consider a 300mm300mm window in an aircraft. For a...Ch. 2 - Consider a small but known volume of metal that...Ch. 2 - Use INT to perform the following tasks. Graph the...Ch. 2 - Calculate the thermal conductivity of air,...Ch. 2 - A method for determining the thermal conductivity...Ch. 2 - Compare and contrast the heat capacity cp of...Ch. 2 - A cylindrical rod of stainless steel is insulated...Ch. 2 - At a given instant of time, the temperature...Ch. 2 - A pan is used to boil water by placing it on a...Ch. 2 - Uniform internal heat generation at q=5107W/m3 is...Ch. 2 - Consider a one-dimensional plane wall with...Ch. 2 - The steady-state temperature distribution in a...Ch. 2 - The temperature distribution across a wall 0.3 m...Ch. 2 - Prob. 2.33PCh. 2 - One-dimensional, steady-state conduction with...Ch. 2 - Derive the heat diffusion equation, Equation 2.26,...Ch. 2 - Derive the heat diffusion equation, Equation 2.29....Ch. 2 - The steady-state temperature distribution in a...Ch. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - The steady-state temperature distribution in a...Ch. 2 - Prob. 2.41PCh. 2 - Prob. 2.42PCh. 2 - cylindrical system illustrated has negligible...Ch. 2 - Beginning with a differential control volume in...Ch. 2 - Prob. 2.45PCh. 2 - Prob. 2.46PCh. 2 - For a long circular tube of inner and outer radii...Ch. 2 - Passage of an electric current through a long...Ch. 2 - Two-dimensional. steady-state conduction occurs in...Ch. 2 - An electric cable of radius r1 and thermal...Ch. 2 - A spherical shell of inner and outer radii ri and...Ch. 2 - A chemically reacting mixture is stored in a...Ch. 2 - A thin electrical heater dissipating 4000W/m2 is...Ch. 2 - The one-dimensional system of mass M with constant...Ch. 2 - Consider a one-dimensional plane wall of thickness...Ch. 2 - A large plate of thickness 2L is at a uniform...Ch. 2 - The plane wall with constant properties and no...Ch. 2 - Consider the steady-state temperature...Ch. 2 - A plane wall has constant properties, no internal...Ch. 2 - A plane wall with constant properties is initially...Ch. 2 - Consider the conditions associated with Problem...Ch. 2 - Consider the steady-state temperature distribution...Ch. 2 - A spherical particle of radius r1 experiences...Ch. 2 - Prob. 2.64PCh. 2 - A plane wall of thickness L=0.1m experiences...Ch. 2 - Prob. 2.66PCh. 2 - A composite one-dimensional plane wall is of...Ch. 2 - Typically, air is heated in a hair dryer by...Ch. 2 - Prob. 2.69P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 5.10 Experiments have been performed on the temperature distribution in a homogeneous long cylinder (0.1 m diameter, thermal conductivity of 0.2 W/m K) with uniform internal heat generation. By dimensional analysis, determine the relation between the steady-state temperature at the center of the cylinder , the diameter, the thermal conductivity, and the rate of heat generation. Take the temperature at the surface as your datum. What is the equation for the center temperature if the difference between center and surface temperature is when the heat generation is ?arrow_forwardIn the design of a certain computer application, a heat flow simulation is required. In the simulation, the heat conductor, which is of length 10m, has a perfectly insulated surface. The temperature at both ends of the conductor is kept consistently at zero. The initial temperature at any point of the conductor is uniform at 25°C. The 1-dimensional heat equation is given as follows: for all 0arrow_forward#4: A rod of length L. coincides with the interval [0, L] on the x-axis. Let u(x, t) be the temperature. Consider the following conditions. (A) The left end is held at temperature 0°. (B) The right end is insulated. (C) There is heat transfer from the lateral surface of the rod into the surrounding medium, which is held at temperature 0° (D) The left end is insulated. (E) The initial temperature is 0° throughout. (F) The right end is held at temperature 0°. (G) There is heat transfer from the right end into the surrounding medium, which is held at a constant temperature of 0°. (H) There is heat transfer from the left end into the surrounding medium, which is held at a constant temperature of 0°. In each part below, determine which of the above conditions corresponds to the given initial or boundary condition for the heat equation. (a) u(x, 0) = 0 (b) u(0, 1) = 0 (c) du (d) ou x=L ox|x=0 = -hu(L, 1) = hu(0, 1)arrow_forwardall of the How much thermal energy is required to heat at water in a swimming pool by 1°C if the dimensions are 4 ft deep by 20 ft wide by 75 ft long? Report your result in megajoules.arrow_forwardA brass plate has a circular hole whose diameter is slightly smaller than the diameter of an aluminum ball. Ifthe ball and the plate are always kept at the same temperature,(a) should the temperature of the system be increased or decreasedin order for the ball to fit through the hole? (b) Choose the bestexplanation from among the following:I. The aluminum ball changes its diameter more with temperature than the brass plate, and therefore the temperatureshould be decreased.II. Changing the temperature won’t change the fact that the ballis larger than the hole.III. Heating the brass plate makes its hole larger, and that willallow the ball to pass through.arrow_forwardConsider the square channel shown in the sketch operating under steady state condition. The inner surface of the channel is at a uniform temperature of 600 K and the outer surface is at a uniform temperature of 300 K. From a symmetrical elemental of the channel, a two-dimensional grid has been constructed as in the right figure below. The points are spaced by equal distance. Tout = 300 K k = 1 W/m-K T = 600 K (a) The heat transfer from inside to outside is only by conduction across the channel wall. Beginning with properly defined control volumes, derive the finite difference equations for locations 123. You can also use (n, m) to represent row and column. For example, location Dis (3, 3), location is (3,1), and location 3 is (3,5). (hint: I have already put a control volume around this locations with dashed boarder.) (b) Please use excel to construct the tables of temperatures and finite difference. Solve for the temperatures of each locations. Print out the tables in the spread…arrow_forward(a) Consider nodal configuration shown below. (a) Derive the finite-difference equations under steady-state conditions if the boundary is insulated. (b) Find the value of Tm,n if you know that Tm, n+1= 12 °C, Tm, n-1 = 8 °C, Tm-1, n = 10 °C, Ax = Ay = 10 mm, and k = = W 3 m. k . Ay m-1, n m, n | Δx=" m, n+1 m, n-1 The side insulatedarrow_forwardSOLVE STEP BY STEO IN DIGITAL FORMAT A horizontal tube 6 m long and 123.5 cm in diameter is maintained at a temperature of 150 °C in a large room in which the air is at 20 "C and 8 W/m² "C The walls of the room are at 38 °C Assume that the emissivity of the tube is 0.76. How much heat is lost from the tube by both convection and radiation?arrow_forwardIn a concentrated solar power plant, molten salt tank is used to store the thermal energy from the sun during the day. The tank wall thickness is 3cm containing molten salt at a temperature of 390 degree Celsius. There is atmospheric air outside the tank at a temperature of 30 degree Celsius. Suppose heat is lost as a result of heat transfer from the molten salt to the atmospheric air. What is the mode of heat transfer in this condition? conduction then convection convection then conduction convection then conduction then convection conduction then convection then conductionarrow_forwardAn engineer seeks to study the effect of temperature on the curing of concrete by controlling the curing temperature in the following way. A sample slab of thickness L is subjected to a heat flux, qw, on one side, and it is cooled to temperature T1 on the other. Derive a dimensionless expression for the steady temperature in the slab. Plot the expression and offer a criterion for neglecting the internal heat generation in the slab.arrow_forward2. A rectangular block has thickness B in the x-direction. The side at x = 0 is held at temperature T, while the side at x = B is held at T2. The other four sides are well insulated. Heat is generated in the block at a uniform rate per unit volume of [. (a) Use the conduction equation to derive an expression for the steady-state temperature profile, T(x). Assume constant thermal conductivity. (b) Use the result of part (a) to calculate the maximum temperature in the block for the following values of the parameters: T₁-120 °C k-0.2 W/(m K) B-1.0 m T₂-0 F-100 W/m³arrow_forwardSketch the temperature distribution in wedge below along the centreline, showing your reasoning andproper equations used. assuming a uniform thermal conductivity and a temperature of 122 °C on the rightface, and 22 °C on the left face. The top and bottom faces are insulated and the solid is long in the direction of the page.arrow_forwardarrow_back_iosSEE MORE QUESTIONSarrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Introduction to Diffusion in Solids; Author: Engineering and Design Solutions;https://www.youtube.com/watch?v=K_1QmKJvNjc;License: Standard youtube license