(2) sz The bar ABCD is fixed at A by a pin and supported by two wires as shown in fig. the bar is subjected to aload of 75 kN at D. the relation between the movement of point N BtoDis TSN 36B =2 8D 26B =3 6D 8B =4 6D None of all these 26B = 8D O OOO0O0 (2) jehäi The bar ABCD is fixed at A by a pinand supported by two wires asshown in fig. the bar is subjectedto a load of 75 kN at D. the relationbetween the movement of point?-------- B to D isCopper2 mrod-Steelrod1 m4 m2 m-2m-в75 kN38B =2 SD O28B =3 SD OSB =4 SDNone of all these O28B = SD%3D

Given:- The bar ABCD is fixed at A The bar ABCD is supported by two wires i.e. steel and copper…

(2) jlibäi The bar ABCD is fixed at A by a pin and supported by two wires as shown in fig. the bar is subjected to a load of 75 kN at D. the relation between the movement of point ?-------- B to D is Copper rod- 2 m Steel rod- 1m 4 m m- 2m B 75 kN

(2) jlibäi The bar ABCD is fixed at A by a pin and supported by two wires as shown in fig. the bar is subjected to a load of 75 kN at D. the relation between the movement of point ?-------- B to D is Copper rod- 2 m Steel rod- 1m 4 m m- 2m B 75 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q1// The force F - 50 lb acts on the gear tooth. Resolve this force into two components acting along…

Q: The rigid bars AB and CD are supported by pins at A and D. The vertical rods are made of aluminum…

A: Determine the vertical displacement of the point where the force P =10 kips is applied.

Q: Given: The truss shown in the figure below. Find: The values (kips) of the reactions at A and H.…

A: Given data Span member length Point loads We will use method of joints to solve this problem

Q: Member AB (helical spring) and Member AC (axial rod) are carrying a weight at point A. Member AB has…

Q: Determine the resultant couple moment of the three couples acting on the plate. F 200 lb %3D F 300…

A: solution there is no need to find the rectangular co-ordinates as we carefully observe the figure…

Q: Question #2: Determine the moment about line AB due to the force couple shown. 60j + 80k lb 5 ft…

Q: Q.1: A shaft composed of segments AB, BC is fixed between the two walls at 4 and C and loaded as…

A: Given that: A composite shaft with 2kNm torque applied at B as shown-

Q: From the truss shown: End 1 is hinged support and end 2 is roller support. If the reaction at the…

A: Given a truss with point load system. Required- to determine the forces in the members 34 52 and 54…

Q: 14 Eiample The beam ABC is loaded via a 500 N.m couple and a 600 N force as shown. The beam is…

Q: 2-am *pin is supported at C •AB is a single hydraulic cylinder •limit of arm DC (horizontal…

Q: The force acting on the gear tooth is F = 20 lb.Resolve this force into two components acting along…

Q: 6.14 Solve Prob. 6.13 assuming that the two steel plates are (a) replaced by 8 x 200-mm plates, (b)…

A: 6.14 Calculate allowable shear for given conditions

Q: *Prob. 1.4-14. Beam AD is supported by a rollers at B and C that are equidistant form the ends, as…

Q: *10-68. A rod is made from two segments: AB is steel and BC is brass. It is fixed at its ends and…

A: As per our rules we only solve the first question.Hence, solution is given for the first…

Q: The rigid bar ABC is supported by AD and BE. Determine: a. Inclination of member ABC after loading…

Q: Use the bisection A beam is loaded as shown in Fig menod to solve for the positon Inside the bram…

Q: etermine the horizontal and vertical components of force which pin A exerts on member ABC. The 800 N…

A: The bottom edge of the particle is the horizontal component and the side opposite the angle is the…

Q: 4.168 A slender, homogeneous, 20-ft rod weighing 64.4 lb is supported as shown in Figure P4.168. The…

Q: Determine the member force GL(kN) in the figure shown. 2n- 50 AN NYost 50 AN 50 AN 30 AN S0 AN -…

A: Consider the figure,

Q: 5. Determine the reactions at the supports in the portal frame shown. Given: E-constant for all…

A: given Data: PL = 12kn and 30kn Need to find VA and HA

Q: 1.60 Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

Q: Q.1: A shaft composed of segments AB, BC is fixed between the two walls at A and C and loaded as…

A: Given that: A composite shaft as shown -

Q: AM IS SUPPORTED BY A PIN AT A AND WIRES P ON THE BEAM CAUSES THE END C TO BE DISP WARD, DETERMINE…

Q: H.W.2: 1,200 mm The load P produces an axial strain of -1,800 ue in post (2). Determine the axial…

Q: . The frame is supported by a hinge at A and a roller at E. Compute the reaction at A. 500 Ib 2000…

Q: The

A: LAB=10/cos40°=13.05 ft LAD=10/cos20∘=10.64 ft ΣFV=0PABcos40∘+PAC+PADcos20∘=10(1000)…

Q: . Figure Q1 shows a steel member imposed with various loadings supported by a roller and pin at A…

A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…

Q: A horizontal member is looded and supported as shown. IOKN verfical support 0.3 m B 0.4m spring…

Q: 1.Calculare the Magnitude (absolute value) of the force in member CA in newtons.The correct answer…

A: m=26kg To find tension in cable CA and vertical component of reaction at point B

Q: Q.1: A shaft composed of segments AB, BC is fixed between the two walls at A and C and loaded as…

A: Given that: A shaft ABC as loaded with a torque at B = 2 kNm.

Q: 2) The stvuct ure shown in the Figure is hinged at A and C. Find the horí gontal and vertical hinge…

Q: Determine the stiffness kT of the single spring suchthat the force F will stretch it by the same…

A: The expression for the force in the spring is given by, Here, F is the force in the spring, k is…

Q: (Mc)y = -226 N-m The shaft is supported at its ends by two bearings A and B and is subjected to the…

Q: e bent rod ABCD is supported with a ball-and- ket joint at A, a hinge at D and the elastic cable at…

Q: Q.1: A shaft composed of segments AB, BC is fixed between the two walls at 4 and C and loaded as…

A: Torque reaction at both supports are required to find. For shaft fixed at both ends angle of twist…

Q: 350 기 mm 2400mm 400mm C A B 200mm 8 notice not hinge E 3 D =1 200kg

A: To Determine Reactions at pin C and D on member CDE where E is a roller and A is a pin

Q: . Bronze pipe (1) has an elastic modulus of E1 16,000 ksi, a cross-sectional area of A1 2.68 in m…

A: Given data ∆=0.25 inPipe 1 Pipe 2E1=16000 Ksi…

Q: The uniform bars AB and BC are connected with a pin at B and placed on a horizontal surface. The…

A: Sketch the free body diagram.

Q: 10. The assembly consists of a steel rod CB and an aluminum rod BA, each having a diameter of 12 mm.…

A: From figure ; consider part BC ; We know that displacement is given by ; δBC = P1L1A1 E1 P1 = 18 -…

Q: PROBLEM 03: The assembly consists of a steel rod CB and an aluminum rod BA, each having a diameter…

Q: gid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that…

A: To find value if load P

Q: etermine the force P (in Newton) needed to lift the load. eglect the weight of the beam. pad =…

A: To find load P

Q: A 13-mm-diameter steel (E = 193 GPa) rod (2) is connected to a 27-mm-wide by 10-mm-thick rectangular…

Q: 2. The rigid bars AB and CD are supported by pins at A and D. The vertical rods are made of aluminum…

Q: A D a b A beam element with a hinge at point B is shown. P-(1+M) kN b-(1+N) m Reaction force in C:…

Q: Determine the reactions at the supports of the beam. Assume that support at B is a roller and EI is…

Q: Question 8 Figure 4. A 17.5 B D For the truss shown, compute for the reaction at Joint B. 16.5 18.5…

A: First we need to fing the vertical reactions at Ra and Rb. So, Sum of upward vertical force = sum of…

Q: Calculate the moment of inertia of the built up section about the horizontal axis located 78.26 mm…

A: Note: As per guideline we are allowed to answer first 3 questions only, so kindly post other…

Q: A horizontal force of F = {-50i} N is appliedperpendicular to the handle of the pipe wrench.…

Question

(2) sz The bar ABCD is fixed at A by a pin and supported by two wires as shown in fig. the bar is subjected to aload of 75 kN at D. the relation between the movement of point N BtoDis TSN 36B =2 8D 26B =3 6D 8B =4 6D None of all these 26B = 8D O OOO0O0

(2) jehäi The bar ABCD is fixed at A by a pin
and supported by two wires as
shown in fig. the bar is subjected
to a load of 75 kN at D. the relation
between the movement of point
?-------- B to D is
Copper
2 m
rod-
Steel
rod
1 m
4 m
2 m-
2m-
в
75 kN
38B =2 SD O
28B =3 SD O
SB =4 SD
None of all these O
28B = SD
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

stress Determine the Maximum Normal S deviloped in the bar bth at the crom section Containing the hole and at the cross sechion Gntaiming the fillets when it's subjected to a tension of P. tam Wom O while: P- 30 KN W= 52 mm t- 4 mm he 24 mm ww 7F de 22 mm k: 90 mm S: Li4 mm
The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm
Rigid members ABC and DEF are joined bysteel (Es = 180 GPa) links BE and CF. The steellinks consist of rectangular plates with crosssectional dimensions 25x35-mm. Determine:a) the change in length of BE and CFb) the distance between pts. A and D after theloading is applied. Pts. A and D are 240mm apart prior to the applied loading.
The homogeneous wire ABCD is bent as shown and is attached to a hinge at C. The length BCindicated by b is 94 mm. Determine the length L for which portion BDC of the wire is horizontal. L В IC 60 mm A The length L for which portion BCD of the wire is horizontal is mm.
Q,28 A plane frame ABCDEFGH shown in figure has clamp support at A, hinge supports at G and H, axial force release at C and moment release (hinge) at E. The static (d) and kinematic (a) indeterminacies respectively are o B A (a) 4,9 (c) 2, 13 l'o'o'o'o 0.000 H-1 (b) 3, 11 (d) 1,14 6x3+4+4)-7-7 Gnot-2.
Q2. (а) A beam is supported and loaded as shown in Figure Q2(a). Point A is a M 6 UTM pin support and point B is reactions at A and B. a roller support. Determine the support ITM M UTM 30 kN O UTM 80 kN/m 30 UTM UTM & UTM UTM :D M UTM 200 kNm 6 m В 12 m UTM TM UI *- *TTM FIGURE Q2(a) 3 UTM TM UTM *TTM
Dr. A H.W.5: A rigid bar ABCD is supported by two bars, as shown in Fig- ure 3 .There is no strain in the vertical bars before load Pis applied. After load P is applied, the normal strain in rod (1) is -570 pm/m. Determine (b) the normal strain in rod (2) if there is a l-mm gap in the connection at pin C before the load is applied. (c) the normal strain in rod (2) if there is a l-mm gap in the connection at pin B before the load is applied. (a) the normal strain in rod (2). (2) 1,500 mm 360 mm 140 mm 240 mm Rigid bar bber C B 900 mm (1)
The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel wires are 1cm in diameter. If the load P is 5kN and the weight of the beam is neglected, solve the deformation at wire BD. E 4 m +2m+2m -3 m O 0.417mm O 0.497mm O 0.329mm O 0.231mm
Aen = a0 © @2 Z Q23-7-2018p.. Q1: A railway ridge consisting of truss construction as shown in the Figure below, this truss is supported by A and B. The forces on joints il and V are i the uss result from a i crossing the railway bridge Determine the following: (a)the reactions forces in A and B (b)the forces of the truss members in joints (1.1, I and 1V) >
the ends tu three Of the Farcep Coupe f the rectonguler plate.are ycdal Couples e Determme So thot moment is 400 the the magnitude resultart Mm anticlackss 2m G-750 N -Q=-250M Calcalah the perpendralor drsknce be tween f ad -f. ard -f. the Coupe Ferces Calaulak Cauple the magntude Cf the Coupe momey Q 1.2. Of H 13 The directrcn OF the couple munmt a Oupir rs. Calcaek the Magnmuk e p
The rigid a pin at A and beam is Supprted by wires BD anod CE. IP the load P on the bean Cause the Point I to be displacedmm dovn warel. delermine to normal strain developd in wires CEard BD
The A-36 steel wires AB and AD each have a diameter of 2 mm and the unloaded lengths of each wire are LAC = 1.70 m and LAB = L AD= 2.00 m В D 4 4 3. Part A Determine the required diameter of wire AC so that each wire is subjected to the same force when the 150-kg mass is suspended from the ring at A.