10. The assembly consists of a steel rod CB and an aluminum rod BA, each having a diameter of 12 mm. If the rod is subjected to the axial loadings at A and at the coupling B, determine the displacement of the coupling B and the end A. The un-stretched length of each segment is shown in the figure. Neglect the size of the connections at B and C, and assume that they are rigid. Est = 200 GPa, Eal = 70 GPa. 3 m B 6 kN 2 m A 18 kN

10. The assembly consists of a steel rod CB and an aluminum rod BA, each having a diameter of 12 mm. If the rod is subjected to the axial loadings at A and at the coupling B, determine the displacement of the coupling B and the end A. The un-stretched length of each segment is shown in the figure. Neglect the size of the connections at B and C, and assume that they are rigid. Est = 200 GPa, Eal = 70 GPa. 3 m B 6 kN 2 m A 18 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 519 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 633 mm2. For the 36 kN force shown, determine the deflection of B (mm) *deflection should have a negative sign if compression and positive if tension. Also, your final answer should have two decimal places
Q2. Two members of Aluminium AB and BC are connected as shown in the Figure Q2.Point A is a fixed end support, point B is a pin connection and point C is a pin support. The cross section of member AB is 120 x 120 mm and member BC is a rod of 120 mm diameter. A forced P is applied to the connection B. Given the young modulus, E = 70 kN/mm² for both members. (a) Prove that both members are slender (Member is slender when the slenderness ratio, λ >90) (b) Determine the maximum load, P that can be carried by the structure. (c) Determine the allowable load, P if the factor of safety is 3.0. 4m P KN B 2m 2m 1m
For the truss shown in the following figure, the temperature of member BC is raised by 140 °C, and member BD is raised by 160 °C. EA=300000 N for all members and a=1/75000 1/°C. Use the stiffness method to do the following: A b) Ay II C Part 1. Calculate the displacements at the joints: a) A₂ = c) B₂ = d) By = e) C₁ = 3112 mm mm mm mm mm -5m- Part 2. Calculate the force in each member: a) NAB= N b) NAC = N c) NBD = N d) NBC = N e) NCD = N f) NAD = N B D 5m
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross sectional area of 500 mm^2. Link CD made of steel (E = 200 GPa) and has a cross sectional area of 600 mm^2. Determine the deflection at D in mm
At a temperature of 53°F, a 0.1 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [a= 12.7 x 10-6/°F] and bar (2) is stainless steel [a= 10.4 x 10-6/°F]. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. Assume L₁ = 40 in., L₂ = 57 in. (1) B A L₁ Answer: Final temperature = i bo L2 °F.
Q2: The pin-connected structure shown in figure below consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E= 105 GPa] with a cross-sectional area of A1= 290 mm2. Bar (2) is an aluminum alloy [E=70 GPa] with a cross-sectional area of A2= 650 mm?. If a load of P= 30 kN is applied at B, determine: (a) the normal stresses in both bars (1) and.(2) (b) the downward deflection of point B on the rigid bar. (1) 2250 mm 670 mm 480 mm 650 mm 1600 mm P = 30 kN
А P 200 mm В E 150 mm F Three steel (E=200 GPa) rods (AB, CD and EF) support a load of P=30 kN as shown in the figure. Each of the rods AB and CD has a 80-mm2 cross-sectional area and rod EF has a 120-mm2 cross-sectional area. (a) Write the equilibrium equation for the rigid member BED in vertical direction, (b) write the compatibility equation for the given bar system, (c) determine the force in rod EF (d) determine the average normal stress in rod EF.
A rigid bar ABCD is supported by two bars as shown in Figure below. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in bar (1) is 590 µ. Determine: a. The normal strain in bar (2). b. The normal strain in bar (2) if there is a 1 mm gap in the connection at pin C before the load is applied. c. The normal strain in bar (2) if there is a 1 mm gap in the connection at pin B before the load is applied. (2) 1,500 mm 240 mm 465mm 140 mm Rigid bar B C 900 mm (1) P.
A bar assembly ABC is loaded with axial force 'P' is constrained at both ends. Analyze a bar element by i) ii) A Determining the reactions at either ends. Determining the reactions at either ends when the joint C is reduced by 'u' mm from wall/constraint joint C. 0.7 L Figure 1 0.5 L U
Calculate the support reactions of the column element given in the figure. Determine the required edge length a to ensure to safety of the element that is made of a material with a safety stress capacity of 200 MPa and that supports the column at point A. ( AB and BC parts have the same material properties. )
A two member truss ABC is shown in the figure. The force (in kN) transmitted in member AB is
The rigid bar AC is supported by two axial bars (1) and (2). Both axial bars are made of bronze [E = 100 GPa; a = 18 x 10-6 mm/mm/ °C). The cross-sectional area of bar (1) is A, = 184 mm2 and the cross-sectional area of bar (2) is A2 = 380 mm2. After load P has been applied and the temperature of the entire assembly has increased by 38°C, the total strain in bar (2) is measured as 1240 µɛ (elongation). Assume L1 = 1290 mm, a = 590 mm, b = 820 mm, and L2 = 2000 mm. Determine: (a) the magnitude of load P. (b) the vertical displacement of pin A. (2) L2 |(1) L1 В a Answers: (a) The magnitude of P = i kN. (b) The vertical displacement of pin A = i mm (down).