(Mc)y = -226 N-m The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T = 585-N forces act in the -z direction and the 200-N and 80-N forces act in the +y direction. The journal bearings at A and B exert only y and z components of force on the shaft. Submit Previous Answers Figure < 1 of 1 Part F Determine the resultant bending moment in the z direction on the cross section at C. Express your answer to three significant figures and include appropriate units. 400 mm 150 mm 150 mm ? B 200 mm 200 mm (Mc): = | 101.115 N•m 300 mm O You have already submitted this answer. Enter a new answer. No credit lost. Try again. 80 N 80 N 200 N Submit Previous Answers Request Answer 200 N Provide Feedback

(Mc)y = -226 N-m The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T = 585-N forces act in the -z direction and the 200-N and 80-N forces act in the +y direction. The journal bearings at A and B exert only y and z components of force on the shaft. Submit Previous Answers Figure < 1 of 1 Part F Determine the resultant bending moment in the z direction on the cross section at C. Express your answer to three significant figures and include appropriate units. 400 mm 150 mm 150 mm ? B 200 mm 200 mm (Mc): = | 101.115 N•m 300 mm O You have already submitted this answer. Enter a new answer. No credit lost. Try again. 80 N 80 N 200 N Submit Previous Answers Request Answer 200 N Provide Feedback

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the magnitude of the pin force at A. Assume W = 645 Ib, a = 3.7 ft, b = 3.0 ft, r = 8 in. a - a r C B A W D Answer:A = i Ib
Determine the magnitude of the pin force at A. Assume W = 875 Ib, a = 2.8 ft, b = 2.1 ft, r = 8 in. C B W Answer: A = i Ib
The force system acting on the machine part is equivalent to the single force R=475i+50j acting at O. (a)Find the value of P. (b)What is the value of the y-component of P? (c)Find the value of b. (d)What is the value of x-component of P?
Determine the magnitude of the pin force at A. Assume W = 895 lb, a = 2.8 ft, b = 2.1 ft, r = 9 in. a C B А W D Answer: A = i Ib
The slender bar AB weighs 50 lb and moves in the vertical plane. The bar was initially held at rest at 0= 30°, when a 20-lb force is suddenly applied at A. Find the forces on the rollers at points A and B. The rollers can be considered smooth and of negligible mass. B 0//G 20 lb L -X
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
Problem # 4. A 12-mm-diameter steel E 200 GPa] rod (2) is connected to a 30mm wide by 8 mm thick rectangular aluminum [E 70 GPa] bar (1), as shown. required to Determine the force P stretch the assembly 10.0 mm. Ans: = A (1) 0.45 m B (2) 1.30 m - C
The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G = 39 GPa). Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm, determine the angle of twist at A. 60 mm TB = 1600 N-m 36 mm TA = 800 N·m A 400 mm B 375 mm --- 250 mm Then, determine the maximum and minimum shearing stress in shaft CD.
Determine the magnitude of the pin force at A. Assume W = 530 Ib, a = 3.6 ft, b = 2.9 ft, r = 9 in. a a B A W D Answer: A = i Ib
А P 200 mm В E 150 mm F Three steel (E=200 GPa) rods (AB, CD and EF) support a load of P=30 kN as shown in the figure. Each of the rods AB and CD has a 80-mm2 cross-sectional area and rod EF has a 120-mm2 cross-sectional area. (a) Write the equilibrium equation for the rigid member BED in vertical direction, (b) write the compatibility equation for the given bar system, (c) determine the force in rod EF (d) determine the average normal stress in rod EF.
M E You have 2 Thank You Best Regare Ms. Nur Akr Figure Q3 shows a truss structure, which is pinned at A and roller supported at B. Horizontal load are applied to the truss as shown in the Figure. By using section method, solve the force in member AC, CD and DE in the figure shown (CO2, PO2, C3). 20KN 10KN 3.5m H →10kN 3.5m E 3.5m D H 15kN 10kN- 5kN G C A 5.0m 3.5m B 000 5kN 5kN Gmail M
Prob 1. The rigid bar below is supported by a pin and two rods and must support a load of 100 kN is placed 3 m from A. The brass (Ebrass = 85 GPa) rod has a cross section of 30 x 30 mm and the copper (Ecopper = 120 GPa) rod 20 x 20 mm. Determine the normal stress and deflection of both bars. 1.5 m 2 m B -copper 100 kN brass- 3m 3 m E