System Dynamics
3rd Edition
ISBN: 9780073398068
Author: III William J. Palm
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 7, Problem 7.16P
A certain tank has a circular bottom area A = 20 ft2. It is drained by a pipe whose linear resistance is R — 150 m-1sec_1. The tank contains water whose mass density is 1.94 slug/ft3.
- Estimate how long it will take for the tank to empty if the water height is initially 30 ft.
- Suppose we dump water into the tank at a rate of 0.1 ft3/sec. If the tank is initially empty and the outlet pipe remains open, find the steady-state height and the time to reach one-third that height, and estimate how long it will take to reach the steady-state height.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Consider the three tank system shown in the figure. All
tanks are completely empty. At time t=0 water flows
into tank 1 at a constant rate of Q and subsequently
flows into tanks 2 and 3. Also, water drains from tanks 1
(1)
(2)
(3)
and tanks 2 as shown.
Develop a model (differential equation system) that will
describe this system.
Assume time constant ,T = 1.
Liquid in a fixed volume closed container isis mixed. X + 400 kJ of work is done to mix the propellerand 500 kJ of heat transfer from the vessel walls to the environment. The internal energy of the liquid in its final state is 660 kJ.As it is known, find the initial internal energy. Draw the system schematically and show the energy flow.(It is assumed that there is no kinetic and potential energy change.)
(X=0)
Problem 1
a) In an open vessel, a certain volume V of water is perfectly agitated by means of an
impeller 20 cm in diameter D. Consider a case in which the impeller steadily rotates at
150 RPM (=revolutions per minute)
Draw up a proper energy balance to find how temperature changes with time as a
result of the power input øw, also named P, by the revolving impeller.
• This Pis given by the formula P = 3.5 PN°D° in which N denotes the impeller speed in
revolutions per second. Calculate P.
When V = 120 litre and the specific heat of water amounts to 4.2 kJ/kgK, calculate
the temperature increase of the water after one hour of stirring.
Chapter 7 Solutions
System Dynamics
Ch. 7 - Prob. 7.1PCh. 7 - Refer to the water storage and supply system shown...Ch. 7 - Prob. 7.3PCh. 7 - In Figure P7.4 the piston of area A is connected...Ch. 7 - Refer to Figure 7.1.4a. and suppose that p\ — p2=...Ch. 7 - Pure water flows into a mixing tank of volume V =...Ch. 7 - Consider the mixing tank treated in Problem 7.6....Ch. 7 - Derive the expression for the fluid capacitance of...Ch. 7 - Prob. 7.9PCh. 7 - Prob. 7.10P
Ch. 7 - 7.11 Derive the expression for the capacitance of...Ch. 7 - Air flows in a certain cylindrical pipe 1 m long...Ch. 7 - Derive the expression for the linearized...Ch. 7 - Consider the cylindrical container treated in...Ch. 7 - A certain tank has a bottom area A = 20 m2. The...Ch. 7 - A certain tank has a circular bottom area A = 20...Ch. 7 - The water inflow rate to a certain tank was kept...Ch. 7 - Prob. 7.18PCh. 7 - Prob. 7.19PCh. 7 - In the liquid level system shown in Figure P7.20,...Ch. 7 - The water height in a certain tank was measured at...Ch. 7 - Derive the model for the system shown in Figure...Ch. 7 - (a) Develop a model of the two liquid heights in...Ch. 7 - Prob. 7.24PCh. 7 - Design a piston-type damper using an oil with a...Ch. 7 - Prob. 7.26PCh. 7 - 7.27 An electric motor is sometimes used to move...Ch. 7 - Prob. 7.28PCh. 7 - Prob. 7.29PCh. 7 - Figure P7.3O shows an example of a hydraulic...Ch. 7 - Prob. 7.31PCh. 7 - Prob. 7.32PCh. 7 - Prob. 7.33PCh. 7 - Prob. 7.34PCh. 7 - Prob. 7.35PCh. 7 - Prob. 7.36PCh. 7 - Prob. 7.37PCh. 7 - (a) Determine the capacitance of a spherical tank...Ch. 7 - Obtain the dynamic model of the liquid height It...Ch. 7 - Prob. 7.40PCh. 7 - Prob. 7.41PCh. 7 - Prob. 7.42PCh. 7 - Prob. 7.43PCh. 7 - Prob. 7.44PCh. 7 - Prob. 7.45PCh. 7 - The copper shaft shown in Figure P7.46 consists of...Ch. 7 - A certain radiator wall is made of copper with a...Ch. 7 - A particular house wall consists of three layers...Ch. 7 - A certain wall section is composed of a 12 in. by...Ch. 7 - Prob. 7.50PCh. 7 - Prob. 7.51PCh. 7 - A steel tank filled with water has a volume of...Ch. 7 - Prob. 7.53PCh. 7 - Prob. 7.54PCh. 7 - Prob. 7.55P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation!arrow_forwardWater is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please thanksarrow_forwardWater is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps pleasearrow_forward
- A circular vessel 2m in diameter and 3m high is one-third filled with liquid A having s.g. of 1.0, one-third filled with liquid B having an s.g. of 2, and the remaining one-third filled with liquid C having an s.g. of 3. At the bottom of the vessel is a 900cm^2 standard circular. Find the time in seconds to empty the vessel through the orifice.arrow_forward1. Determine the mass flow rate in lbm/s of a liquid (ρ = 0.8 g/cm3) flowing through a 2 in (inside diameter) pipe at 480 m/min. 2. A horizontal pipe of cross section 1.5 in2has a constriction of cross section of 2 cm2. Gasoline flows in the larger pipe with a speed of 500 m/hr. Find the speed in the constriction in ft/min.arrow_forwardThe cylindrical in the figure is filled with 31.4 m3 of water at t = 0. The radius of the tank is 1 m and its height is 10 m. There is an outlet line with a radius of 0.1 m at the bottom of the tank. a. What is the time required for half of the water in the tank to drain after the outlet line is opened?b. The flow velocity of water from the bottom of a water tank is related to the height of the water in the tank, and this relation is v² = 2gh where v: (m / s) linear flow velocity, g: gravitational acceleration (10 m / s2) and h: (m) height.arrow_forward
- Help me pleasearrow_forward(c) As shown in Figure 2.4(a), a liquid of constant density p drains from a large tank to the surrounding atmosphere through a long circular pipe of length h and diameter D. Exasperated that it is taking so long to drain the tank, a simple-minded engineer removes the tube so that the liquid drains directly to the surrounding atmosphere through a hole of diameter D, as shown in Figure 2.4(b). The engineer also tries to replace the constant diameter pipe with a tapered pipe having inlet and outlet diameters of D and 0.5D, respectively, and a length of h, as shown in Figure 2.4(c). The tapered pipe's diameter varies linearly along the length of the pipe. In all three cases, the height of the liquid in the tank is H and it is assumed that the liquid level in the tank falls very slowly. Assume that the flow is inviscid, and that the pipes are completely filled with liquid. The liquid's exit velocities are V₁, V2 and V3 for Figures 2.4(a), (b) and (c), respectively. (i) Express V₁, V₂ and V3…arrow_forwardA tank initially holds 100 gal of a brine solution containing 1 lb of salt. At t = 0 another brine solutioncontaining 1 lb of salt per gallon is poured into the tank at the rate of 3 gal/min, while the wellstirredmixture leaves the tank at the same rate. Find:a. the amount of salt in the tank at any time t and b. the time at which the mixture in the tank contains 2 lb of salt.arrow_forward
- An open container made of metal is placed ona scale. Water flows into the container through an opening at the top. At the same time, water flows from the container through the two-equal 45° deflection opening at the sides (Figure Q2). The metal cylinder height is 65 cm, having a diameter of 26 cm, and weighs 21 N when empty. Under normal steady flow conditions, the water level maintained at 58 cm measured from the bottom of the container. One of your friends claims that we can treat this as a simple statics problem by saying that the scale will measure the weight of the volume of water in the tank plus the tank weight only but you disagree with his/her statement. You make a message that says that flow analysis is required. Proof that you are right.|arrow_forwardA cylindrical tank is being filled with water flowing with constant velocity V1 through a tap (Tap 1) that has an opening of diameter D1. The tank is initially empty and contains a tap (Tap 2) placed H1 m above the bottom of the tank that drains water at a velocity of V2 = √2gh. Assuming flow through Tap 2 starts the moment Tank 1 height reaches H1 m, write the differential equation governing the change of water level inside the tank with time (dh/dt=? );i) Before water level reaches H1.ii) After water level reaches H1 up until the tank is full. Do NOT attempt to solve the differential equations!Just drive the differential equations and write the boundaries of the definite integrals.arrow_forwardImagine the water level in the tank as shown in the Figure rises at a rate of 0.004579 ft³/sec. then find: i) The volume flowrate of water leaving the tank (Q3) in ft³/s from pipe 3. ii) The average velocity of water leaving the tank (V3) in ft/s from pipe 3. Pipe 1: Qi=0.0109 ft²/s Pipe 2: Q₂ = 0.025 ft³/s Pipe 3: dy = 1.5 in. V₁ = ?! Q₁ =?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
8.01x - Lect 27 - Fluid Mechanics, Hydrostatics, Pascal's Principle, Atmosph. Pressure; Author: Lectures by Walter Lewin. They will make you ♥ Physics.;https://www.youtube.com/watch?v=O_HQklhIlwQ;License: Standard YouTube License, CC-BY
Dynamics of Fluid Flow - Introduction; Author: Tutorials Point (India) Ltd.;https://www.youtube.com/watch?v=djx9jlkYAt4;License: Standard Youtube License