System Dynamics
3rd Edition
ISBN: 9780073398068
Author: III William J. Palm
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 7, Problem 7.14P
Consider the cylindrical container treated in Example 7.4.3. Suppose the outlet flow is turbulent. Derive the dynamic model of the system (a) in terms of the gage pressure p at the bottom of the tank and (b) in terms of the height /i.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
FLUID MECHANICS: Find the flow rate of water through the system shown for the turbine to produce 20 kW. Neglect friction in your calculations ANSWER SHOULD BE: Q=10.75m3/s
Solve problem 2 (Textbook, p. 230). This is a case example how to use the characteristic curve of a pump to find the operation point of a piping installation. You can find the solution graphically, iteratively (if you want to fit the curve of Fig. P4.2 with an equation) or using trial and error (my recommendation).
2. Pump and pipeline—M . The head/discharge curve of a centrifugal pump is shown in Fig. P4.2. The exit of the pump is connected to 1,000 ft of nominal 2-in. diameter horizontal pipe (D = 2.067 in.). What flow rate (ft^3/s) of water can be expected? Assume atmospheric pressure at the pump inlet and pipe exit, and take fF = 0.00475.
3.0 Consider two cases involving parallel flow of dry air at V=V= 1.5 m/s, T∞=T∞=45°C, and atmospheric pressure over an isothermal plate at Ts=Ts=20°C. In the first case, Rex,c=Rex,c=5 × 105, while in the second case the flow is tripped to a turbulent state at x=x=0 m. At what xx‐location, in m, are the thermal boundary layer thicknesses of the two cases equal? What are the local heat fluxes, in W/m2, at this location for the two cases?
Chapter 7 Solutions
System Dynamics
Ch. 7 - Prob. 7.1PCh. 7 - Refer to the water storage and supply system shown...Ch. 7 - Prob. 7.3PCh. 7 - In Figure P7.4 the piston of area A is connected...Ch. 7 - Refer to Figure 7.1.4a. and suppose that p\ — p2=...Ch. 7 - Pure water flows into a mixing tank of volume V =...Ch. 7 - Consider the mixing tank treated in Problem 7.6....Ch. 7 - Derive the expression for the fluid capacitance of...Ch. 7 - Prob. 7.9PCh. 7 - Prob. 7.10P
Ch. 7 - 7.11 Derive the expression for the capacitance of...Ch. 7 - Air flows in a certain cylindrical pipe 1 m long...Ch. 7 - Derive the expression for the linearized...Ch. 7 - Consider the cylindrical container treated in...Ch. 7 - A certain tank has a bottom area A = 20 m2. The...Ch. 7 - A certain tank has a circular bottom area A = 20...Ch. 7 - The water inflow rate to a certain tank was kept...Ch. 7 - Prob. 7.18PCh. 7 - Prob. 7.19PCh. 7 - In the liquid level system shown in Figure P7.20,...Ch. 7 - The water height in a certain tank was measured at...Ch. 7 - Derive the model for the system shown in Figure...Ch. 7 - (a) Develop a model of the two liquid heights in...Ch. 7 - Prob. 7.24PCh. 7 - Design a piston-type damper using an oil with a...Ch. 7 - Prob. 7.26PCh. 7 - 7.27 An electric motor is sometimes used to move...Ch. 7 - Prob. 7.28PCh. 7 - Prob. 7.29PCh. 7 - Figure P7.3O shows an example of a hydraulic...Ch. 7 - Prob. 7.31PCh. 7 - Prob. 7.32PCh. 7 - Prob. 7.33PCh. 7 - Prob. 7.34PCh. 7 - Prob. 7.35PCh. 7 - Prob. 7.36PCh. 7 - Prob. 7.37PCh. 7 - (a) Determine the capacitance of a spherical tank...Ch. 7 - Obtain the dynamic model of the liquid height It...Ch. 7 - Prob. 7.40PCh. 7 - Prob. 7.41PCh. 7 - Prob. 7.42PCh. 7 - Prob. 7.43PCh. 7 - Prob. 7.44PCh. 7 - Prob. 7.45PCh. 7 - The copper shaft shown in Figure P7.46 consists of...Ch. 7 - A certain radiator wall is made of copper with a...Ch. 7 - A particular house wall consists of three layers...Ch. 7 - A certain wall section is composed of a 12 in. by...Ch. 7 - Prob. 7.50PCh. 7 - Prob. 7.51PCh. 7 - A steel tank filled with water has a volume of...Ch. 7 - Prob. 7.53PCh. 7 - Prob. 7.54PCh. 7 - Prob. 7.55P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Create the simulation model of the 3-tank system shown in Figure. S= 0,25 m2 SO=0,00065 m2 H=0,2 m Q1=0,008 m/s Q2-0,005m/s Simulate the course of the liquid level positions for different initial conditions and evaluate the steady state values. Case a: Case c: h10=1,2m h20=1m h30-0,7m Case b: h10-0,8m h20=1m h10-1,2m h20-1m h30=0,7m h30-0,1marrow_forwardIn Prob. it would be difficult to solve for Ω because of itappears in all three of the dimensionless pump coefficients.Suppose that, in Prob. 5.61, Ω is unknown but D = 12 cmand Q = 25 m 3 /h. The fluid is gasoline at 20 ° C. Rescale thecoefficients, , to make a plot ofdimensionless power versus dimensionless rotation speed.Enter this plot to find the maximum rotation speed Ωforwhich the power will not exceed 300 W.arrow_forwardConsider the flow of a fluid between point 1 and 2. Compute the direction of flow, whether the fluid flows from point 1 to 2 or 2 to 1. Point 2 Point 1 The properties are listed below: Point 1: Pump Pressure = 1.25 x 105 Pa, Cross-sectional area - 15 x 104 m², Fluid velocity = 1 m/s Point 2: Pressure = 1.05 x 10³ Pa, Cross-sectional area = 5 x 104 m² Elevation above point 1-3m Other data: 3 m Density of fluid = 1000 kg/m³ Power delivered by the pump = 7.5 W (Assume efficiency = 100%)arrow_forward
- A wind tunnel has an incompressible flow of air, flowing horizontally from an inlet section, 7 times the test section. A u-tube is connected, containing mercury inside. The mercury has 1.33x10^5 N/m^3 specific weight. The condition of the air at the inlet section is at 1 atm and 280K respectively. What is the change of height inside the mercury, when the velocity at the throat is 70m/s?Complete solutionround off to 4 decimal placesarrow_forwardExample: Vane Problem Fluid of density and velocity impinges on a vane as shown below. Find the reaction forces necessary to keep the vane fixed. 1. Assume jet exits at speed 2. Assume jet has even area 3. Assume jet is at atmospheric pressure 4. Neglect gravitational forces 0 Varrow_forwardExample (1-2): A 2.5 cm diameter water jet exerts a force of 90 kN in the direction of flow on a flat plate which is held inclined at an angle of 30° with the axis of stream. Find the rate of flow.arrow_forward
- Problem 4.35 4-35 Water flows steadily through a pipe of length L and radius R=75 mm. Calculate the uniform inlet velocity, U, if the velocity distribution across the outlet is given by 14 = Ugan and M-3 m/s. R² R [Difficulty: 2]arrow_forwardExample 3.8.In Example 3.7 we considered a vacuum system with zero leaks. No real vacuum systems aretotally leak-free; engineers work very hard to keep the leakage rate as low as possible. If thetank in Example 3.7 has a leak of 0.0001 lbm/min of air, what will the pressure-time plot looklike, and what will be the final pressure? ex: 3.7 is postedarrow_forwardA turbine (see the figure of Example IIIa.3.21) is located at an elevation H1 from the surface of a lake with the discharge pipe located at an elevation H2 from the turbine centerline. Find flow velocity, V4 in terms of H1, H2, P1, P4, h,, and p where subscript 4 refers to the discharge piping. [Ans.: V, = (2/p)[(R – P.) + pg (Z, – Z, –h,)]. Lake H, h. D2 4 D4 H4 Turbinearrow_forward
- FLUID FLOW Example 5: A liquid food with a density of 800 kg/m³ is being transported at a rate of 5 ton/h through the system shown below. If the pressure at point 1 is 20 kPa gage, determine the pressure at point 2. Neglect friction losses. Example 5 P₁ = 20 kPa D₁ = 0.08 m 6 m 2 FLUID FLOW P₂ = ? D₂ = 0.025 marrow_forwardB Problem 2. As illustrated in (a) Fig. P2, an air blower is directed seat at a chair with curved seat of mass mal and legs of mass mjegs For the dimensions given on the mouthpiece figure, and for a given air flow legs rate Q, derive formulas for: (b) a) the water level difference h in the connected tube; b) the force F exerted by air on the mouthpiece; c) the condition for whether or not the blown air will overturn B the chair,arrow_forward1. A 100-mm diameter plunger (section 1) is being pushed at 60 mm/s into a tank filled with a fluid with a fluid of SG = 0.68. If the fluid is incompressible, how many pounds per second is being forced out at section 2, D2 = 20 mm? Answer: 0.707 lbf/sarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
8.01x - Lect 27 - Fluid Mechanics, Hydrostatics, Pascal's Principle, Atmosph. Pressure; Author: Lectures by Walter Lewin. They will make you ♥ Physics.;https://www.youtube.com/watch?v=O_HQklhIlwQ;License: Standard YouTube License, CC-BY
Dynamics of Fluid Flow - Introduction; Author: Tutorials Point (India) Ltd.;https://www.youtube.com/watch?v=djx9jlkYAt4;License: Standard Youtube License