Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
10th Edition
ISBN: 9780073398204
Author: Richard G Budynas, Keith J Nisbett
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 11, Problem 40P
A countershaft is supported by two tapered roller bearings using an indirect mounting. The radial bearing loads are 560 lbf for the left-hand bearing and 1095 for the right-hand bearing. An axial load of 200 lbf is carried by the left bearing. The shaft rotates at 400 rev/min and is to have a desired life of 40 kh. Use an application factor of 1.4 and a combined reliability goal of 0.90, assuming distribution data from manufacturer 1 in Table 11-6. Using an initial K = 1.5, find the required radial rating for each bearing. Select the bearings from Fig. 11-15.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The design load on a ball bearing is 413 lbf and an application factor of 1.2 is appro-
priate. The speed of the shaft is to be 300 rev/min, the life to be 30 kh with a reliability
of 0.99. What is the C10 catalog entry to be sought (or exceeded) when searching for a
deep-groove bearing in a manufacturer's catalog on the basis of 106 revolutions for rat-
ing life? The Weibull parameters are xo = 0.02, (0 – xo) = 4.439, and b = 1.483.
%3D
A stone crusher machine working 8 hours a day is driven by an electric motor with a narrow-V belt-pulley mechanism. The transmitted power is P = 18.5 kW, the speed of the motor is n1 = 1450 RPM, and the required rotational speed for the stone machine is n2 = 690D / d. Sizing of the narrow-V belt-pulley mechanism is required according to the given. Recommended value for the axle spacing a = k. (dw1 + dw2) k = 0.9
Problem 2
A 02-series single-row deep-groove ball bearing with a 65-mm bore (see Tables 11–1 and 11–
2 for specifications) is loaded with a 10-kN axial load and a 15-kN radial load. The inner ring
rotates at 500 rev/min.
(a) Determine the equivalent radial load that will be experienced by this bearing.
(b) Determine whether this bearing should be expected to carry this load with a 95 percent
reliability for 20 kh.
Chapter 11 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Ch. 11 - Manufacturer Rating Life, Revolutions Weibull...Ch. 11 - Manufacturer Rating Life, Revolutions Weibull...Ch. 11 - Manufacturer Rating Life, Revolutions Weibull...Ch. 11 - Problems 112 and 113 raise the question of the...Ch. 11 - Prob. 5PCh. 11 - Manufacturer Rating Life, Revolutions Weibull...Ch. 11 - Two ball bearings from different manufacturers are...Ch. 11 - 11-8 to 11-13 For the bearing application...Ch. 11 - 11-8 to 11-13 For the bearing application...Ch. 11 - 11-8 to 11-13 For the bearing application...
Ch. 11 - 11-8 to 11-13 For the bearing application...Ch. 11 - 11-8 to 11-13 For the bearing application...Ch. 11 - 11-8 to 11-13 For the bearing application...Ch. 11 - A countershaft carrying two V-belt pulleys is...Ch. 11 - A countershaft carrying two V-belt pulleys is...Ch. 11 - A countershaft carrying two V-belt pulleys is...Ch. 11 - A countershaft carrying two V-belt pulleys is...Ch. 11 - For the shaft application defined in Prob. 3-77,...Ch. 11 - For the shaft application defined in Prob. 3-79,...Ch. 11 - An 02-series single-row deep-groove ball bearing...Ch. 11 - An 02-series single-row deep-groove ball bearing...Ch. 11 - 11-22 to 11-26 An 02-series single-row deep-groove...Ch. 11 - 1122 to 1126 An 02-series single-row deep-groove...Ch. 11 - 1122 to 1126 An 02-series single-row deep-groove...Ch. 11 - 1122 to 1126 An 02-series single-row deep-groove...Ch. 11 - 1122 to 1126 An 02-series single-row deep-groove...Ch. 11 - The shaft shown in the figure is proposed as a...Ch. 11 - Repeat the requirements of Prob. 11-27 for the...Ch. 11 - The shaft shown in the figure is proposed as a...Ch. 11 - Repeat the requirements of Prob. 11-29 for the...Ch. 11 - Shown in the figure is a gear-driven squeeze roll...Ch. 11 - The figure shown is a geared countershaft with an...Ch. 11 - The figure is a schematic drawing of a...Ch. 11 - A gear-reduction unit uses the countershaft...Ch. 11 - The worm shaft shown in part a of the figure...Ch. 11 - In bearings tested at 2000 rev/min with a steady...Ch. 11 - A 16-tooth pinion drives the double-reduction...Ch. 11 - Estimate the remaining life in revolutions of an...Ch. 11 - The same 02-30 angular-contact ball bearing as in...Ch. 11 - A countershaft is supported by two tapered roller...Ch. 11 - For the shaft application defined in Prob. 3-74,...Ch. 11 - For the shaft application defined in Prob. 3-76,...Ch. 11 - Prob. 43PCh. 11 - The gear-reduction unit shown has a gear that is...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Consider the belt drive having a diameter of 150 mm that is mounted on the overhung end of ashaft, 30 mm from the nearest bearing. The stepped shaft is made of steel having Su = 965 MPa(140 ksi). The shaft diameter, d, is 30 mm. The bearing bore, D, is 36 mm. The fillet with amachined surface has a radius, r, of 3 mm. What is the safety factor with respect to eventualfatigue failure of the shaft?arrow_forward4. A bearing is subjected to a radial force of 8kN and a thrust force of 3 kN. The values of X and Y factors are 0.56 and 1.5 respectively. The shaft rotates at 1200 RPM. The diameter of the shaft is 75mm and Bearing no. 6315 (C= 112000N) is selected for this application. Estimate the life of this bearing with 90% reliability.arrow_forward5. Design a sleeve coupling for the transmission of 12 kW at 300 rpm by two connected steel shafts. Take service factor KS 1.25. The sleeve is made of CI. The key and the shaft are made of the same material. Allowable stress: Shear stresses in key and shaft 50 MPa Crushing stress in key= 100 MPa Shear stress in CI sleeve = 10 MPaarrow_forward
- A cylinder with a nominal 2.5 in ID, a 4.0 in OD, and a 3.0 in length is to be mated with a solid shaft with a nominal 2.5 in diameter. A medium drive fit is desired (as defined in Table 7-9). The cylinder and shaft are made from steel, with Sy = 100 kpsi and E = 30 Mpsi. The coefficient of friction for the steel interface is 0.7. a. Specify the maximum and minimum allowable diameters for both the cylinder hole and the shaft. b. Determine the torque that can be transmitted through this joint, assuming the shaft and cylinder are both manufactured within their tolerances such that the minimum interference is achieved. c. Suppose the shaft and cylinder are both manufactured within their tolerances such that the maximum interference is achieved. Check for yielding of the cylinder at its inner radius by finding the following: i. The pressure at the interface ii. The tangential and radial stresses in the cylinder, at its inner radius. iii. The factor of safety for static yielding of the…arrow_forwardb) Design a self-aligning ball bearing with basic dynamic load rating of 69.5 KN to be used in the automobile industry to carry a thrust load of 1184 N. The expected life of the bearing is 5201 hours at 628 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.7 and radial and axial load factors are 1.4 and 2.2 respectively, the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Radial load acting on the bearing in Narrow_forward1. Select a single row, deep grove ball bearing that carries a 35 mm diameter shaft. It carries an axial load of F. - 2000 N and a radial load F, = 8000 N. Outer race rotates and a life of 5000 hours at 120 rpm is expected. Verify your selection by a second iteration for dynamic load rating. 2. The journal bearing of a small steam turbine has length L = 50 mm and diameter D = 50 mm. It encounters aarrow_forward
- Select an angular contact ball bearing to carry a radial load of 336lb at a shaft speed of 1800 rpm for 5500 hours. Anapplicationfactorof1.2isappropriate. Use a reliability of 96%.arrow_forwardA bearing with a is loaded with a 2-kN axial load and a 8-kN radial load. The outer ring rotates at 600 rev/min with prdicted desing life of 1000 h. a. Determine the equivalent radial load that will be experienced by this particular bearing. b. Determine the Dynamic load rating that will be used for bearing selection c. Make the selection ex (series type bore diameter outer bearing diameter)arrow_forwardProblem 6 An 02-series single-row deep-groove ball bearing with an 80 mm bore is loaded with a 5-kN axial load and a 9-KN radial load. The bearing has the basic dynamic load rating C₁0 of 70.2kN and basic static load rating Co of 45kN. The outer ring rotates at 500 rev/min. Use the Weibull parameters for Manufacturer 2: x₁=0.02; ; b=1.483. 0 = 4.459 and the application factor of 1.0. (a) Determine the equivalent radial load that will be experienced by this particular bearing. (b) Determine whether this bearing should be expected to carry this load with a 95 percent reliability for 15 kh.arrow_forward
- A certain application requires a ball bearing with the inner ring rotating, with a design life of LD = 15 kh at a speed of nD = 480 rev/min. The radial load is Fr = 1.4 kN, the axial load Fa = 0.4 kN, and an application factor of af = 1.2 is appropriate. The reliability goal, R = 0.99. a) Determine the multiple of rating life required, xD, and the catalog rating C10FR, where FR is the calculated bearing load in [kN] with which we enter a bearing table. Specify a 02-series angular contact ball bearing from Table 11–2, b) Estimate the reliability (R) and multiple of rating-life (XD) in use.arrow_forwardA device contains two bearings is to operate at 300 rev/min, 8 hours per day, 5 days per week for 5 years with a reliability of 0.99. The design load is 2024 N and an application factor of 1.2 is appropriate. Find the catalog rating C10 For ball bearings For roller bearings The Weibull parameters are and Use SI units. Take the relations as and Where the subscripts D: desired R: rating f: factorarrow_forwardA certain application requires a ball bearing with the inner ring rotating, with a design life of 25 kh at a speed of 400 rev/min. The radial load is 3.5 kN and an application factor of 1.5 is appropriate. The reliability goal is 0.90. Find the multiple of rating life required, Xp and the catalog rating C10 with which to enter a bearing table. Choose a 02-series deep-groove ball bearing from Table 11-2, and estimate the reliability in use.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License