Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
10th Edition
ISBN: 9780073398204
Author: Richard G Budynas, Keith J Nisbett
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 11, Problem 2P
Manufacturer | Rating Life, Revolutions | Weibull Parameters Rating Lives | ||
x0 | θ | b | ||
1 | 90(106) | 0 | 4.48 | 1.5 |
2 | 1(106) | 0.02 | 4.459 | 1.483 |
An angular-contact inner ring rotating, 02-series ball bearing is required for an application in which the life requirement is 40 kh at 520 rev/min. The design radial load is 725 lbf. The application factor is 1.4. The reliability goal is 0.90. Find the multiple of rating life xD required and the catalog rating C10 with which to enter Table 11-2. Choose a bearing and estimate the existing reliability in service.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A device contains two bearings is to operate at 300 rev/min, 8 hours per day, 5 days per week for 5 years with a reliability of 0.99. The design load is 2024 N and an application factor of 1.2 is appropriate. Find the catalog rating C10
For ball bearings
For roller bearings
The Weibull parameters are and Use SI units. Take the relations as
and
Where the subscripts
D: desired
R: rating
f: factor
d = 1.25 inch
speed 2200 rpm
12000 Ibf
d.
Shaft load = 2000 lbf
(centered between bearings)
Temperature: 170 F
Tr
Bearing specs:
O, = 25
Length ratio= 0.80
clearance ratio:
Cd
-0.002
2. Hydrodynamic bearings are to be selected for the design shown above. Find the following:
eccentricity ratio e
eccentricity e
in., hmin
in.,
Pavs.
Ibf/in, Torsional resistance T,
in-lbf,
Viscosity n
microreyn, Oil type: SAE
, power loss o
HP
1. Select a single row, deep grove ball bearing that carries a 35 mm diameter shaft. It carries an axial load of F, =
2000 N and a radial load F, = 8000 N. Outer race rotates and a life of 5000 hours at 120 rpm is expected. Verify
your selection by a second iteration for dynamic load rating.
%3!
2. The journal bearing of a small steam turbine has length L = 50 mm and diameter D = 50 mm. It encounters a
Chapter 11 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Ch. 11 - Manufacturer Rating Life, Revolutions Weibull...Ch. 11 - Manufacturer Rating Life, Revolutions Weibull...Ch. 11 - Manufacturer Rating Life, Revolutions Weibull...Ch. 11 - Problems 112 and 113 raise the question of the...Ch. 11 - Prob. 5PCh. 11 - Manufacturer Rating Life, Revolutions Weibull...Ch. 11 - Two ball bearings from different manufacturers are...Ch. 11 - 11-8 to 11-13 For the bearing application...Ch. 11 - 11-8 to 11-13 For the bearing application...Ch. 11 - 11-8 to 11-13 For the bearing application...
Ch. 11 - 11-8 to 11-13 For the bearing application...Ch. 11 - 11-8 to 11-13 For the bearing application...Ch. 11 - 11-8 to 11-13 For the bearing application...Ch. 11 - A countershaft carrying two V-belt pulleys is...Ch. 11 - A countershaft carrying two V-belt pulleys is...Ch. 11 - A countershaft carrying two V-belt pulleys is...Ch. 11 - A countershaft carrying two V-belt pulleys is...Ch. 11 - For the shaft application defined in Prob. 3-77,...Ch. 11 - For the shaft application defined in Prob. 3-79,...Ch. 11 - An 02-series single-row deep-groove ball bearing...Ch. 11 - An 02-series single-row deep-groove ball bearing...Ch. 11 - 11-22 to 11-26 An 02-series single-row deep-groove...Ch. 11 - 1122 to 1126 An 02-series single-row deep-groove...Ch. 11 - 1122 to 1126 An 02-series single-row deep-groove...Ch. 11 - 1122 to 1126 An 02-series single-row deep-groove...Ch. 11 - 1122 to 1126 An 02-series single-row deep-groove...Ch. 11 - The shaft shown in the figure is proposed as a...Ch. 11 - Repeat the requirements of Prob. 11-27 for the...Ch. 11 - The shaft shown in the figure is proposed as a...Ch. 11 - Repeat the requirements of Prob. 11-29 for the...Ch. 11 - Shown in the figure is a gear-driven squeeze roll...Ch. 11 - The figure shown is a geared countershaft with an...Ch. 11 - The figure is a schematic drawing of a...Ch. 11 - A gear-reduction unit uses the countershaft...Ch. 11 - The worm shaft shown in part a of the figure...Ch. 11 - In bearings tested at 2000 rev/min with a steady...Ch. 11 - A 16-tooth pinion drives the double-reduction...Ch. 11 - Estimate the remaining life in revolutions of an...Ch. 11 - The same 02-30 angular-contact ball bearing as in...Ch. 11 - A countershaft is supported by two tapered roller...Ch. 11 - For the shaft application defined in Prob. 3-74,...Ch. 11 - For the shaft application defined in Prob. 3-76,...Ch. 11 - Prob. 43PCh. 11 - The gear-reduction unit shown has a gear that is...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The design load on a ball bearing is 413 lbf and an application factor of 1.2 is appro- priate. The speed of the shaft is to be 300 rev/min, the life to be 30 kh with a reliability of 0.99. What is the C10 catalog entry to be sought (or exceeded) when searching for a deep-groove bearing in a manufacturer's catalog on the basis of 106 revolutions for rat- ing life? The Weibull parameters are xo = 0.02, (0 – xo) = 4.439, and b = 1.483. %3Darrow_forwardA certain application requires a ball bearing with the inner ring rotating, with a design life of LD = 15 kh at a speed of nD = 480 rev/min. The radial load is Fr = 1.4 kN, the axial load Fa = 0.4 kN, and an application factor of af = 1.2 is appropriate. The reliability goal, R = 0.99. a) Determine the multiple of rating life required, xD, and the catalog rating C10FR, where FR is the calculated bearing load in [kN] with which we enter a bearing table. Specify a 02-series angular contact ball bearing from Table 11–2, b) Estimate the reliability (R) and multiple of rating-life (XD) in use.arrow_forwardA device contains two bearings is to operate at 300 rev/min, 8 hours per day, 5 days per week for 5 years with a reliability of 0.99. The design load is (2006) N and an application factor of 1.2 is appropriate. Find the catalog rating C10 a)For ball bearings b) For roller bearings The Weibull parameters are x0=0.02 ,(θ-x0)=4.439 and b=1.483 Use SI units. Take the relations as C10=afFD[xD/x0+(θ-x0)(1-RD)1/b]1/a and xD=LDηD60/LR Where the subscripts D: desired R: rating f: factorarrow_forward
- A propeller shaft rotating at constant speed is subjected to variable loads.Ball bearing supporting the shaft are subject to variable radial loads as follows;16KN for 40 percent of the time,2KN for 10 percent of the time,4KN for 20percent of the time and no load for the remaining time of the cycle.The total life expected for bearing is 3×10^6 revolution at a liability of 94 percent.select the bearing by calculating; a)Net dynamic load for the bearing b)load rating of the bearing from the manufacturers cataloguearrow_forwardDesign a single row deep groove ball bearing with basic dynamic load rating of 33 KN to be used in a turbine to carry a radial load of 1612 N. The expected life of the bearing is 5400 hours at 501 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.8. The radial and axial load factors are 1.3 and 1.6 respectively and the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Axial load acting on the bearing in Narrow_forwardAn 02-series ball bearing is to be selected to carry a radial load of 8 kN and a thrust load of 4 kN. The desired life Lp is to be 5000 h with an inner-ring rotation rate of 900 rev/min. What is the basic load rating that should be used in selecting a bearing for a reliability goal of 0.90? Hints: Rating life is 1(10°) revolutions, Weibull parameters of rating lives are x, = 0.02,0 = 4.459, b = 1.483 respectively.arrow_forward
- A No. 207 radial-contact ball bearing supports a shaft that rotates at 44 rpm. A radial load varies in such a way that 60, 30, and 10 percent of the time the load is 0.68kN, 1.6kN and 1kN, respectively. The loads are uniform. Estimate the L10 life in hours. An error of 5% is allowed for. There are no decimal spaces required.arrow_forward4. A bearing is subjected to a radial force of 8kN and a thrust force of 3 kN. The values of X and Y factors are 0.56 and 1.5 respectively. The shaft rotates at 1200 RPM. The diameter of the shaft is 75mm and Bearing no. 6315 (C= 112000N) is selected for this application. Estimate the life of this bearing with 90% reliability.arrow_forwardb) Design a single row deep groove ball bearing with basic dynamic load rating of 33 KN to be used in a turbine to carry a radial load of 1584 N. The expected life of the bearing is 5591 hours at 529 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.8. The radial and axial load factors are 1.3 and 1.6 respectively and the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Axial load acting on the bearing in Narrow_forward
- Dynamic load number C = 40500 N, revolution n = 840 rpm and Fr = 4500 of 6309 single row fixed radial bearing carrying N load; (a) Check and interpret whether it is selected correctly for Lh=20000 hours. (b) Calculate the dynamic load number of the bearing when the load remains the same and the life is doubled.arrow_forwardA certain application requires a ball bearing with the inner ring rotating, with a design life of 25 kh at a speed of 400 rev/min. The radial load is 3.5 kN and an application factor of 1.5 is appropriate. The reliability goal is 0.90. Find the multiple of rating life required, Xp and the catalog rating C10 with which to enter a bearing table. Choose a 02-series deep-groove ball bearing from Table 11-2, and estimate the reliability in use.arrow_forwardb) Design a self-aligning ball bearing with basic dynamic load rating of 69.5 KN to be used in the automobile industry to carry a thrust load of 1184 N. The expected life of the bearing is 5201 hours at 628 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.7 and radial and axial load factors are 1.4 and 2.2 respectively, the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Radial load acting on the bearing in Narrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License