What does the shear flow measure?

Q: Warning-If not anything upto the mark, I'll report and dislike you. Draw figure of uniaxial state of…

A: Uniaxial State of stress-  this type of stress has only one principal stress. ie , when an object is…

Q: Determine optimum velocity ?

A: Given: Rotor diameter,d=9 mSpeed,N=2700 rpmNozzle angle,α=300Optimum velocity:    It is defined as…

Q: = missing properties

A: Solution given below.

Q: Write short notes on significance of grashoff number.

A: The answer is given below

Q: the diameter of the llowable shear stres

A:

Q: the normal and shearing

A: To determine the normal and shear stress .

Q: Q13) For the following micrometer: a- What is the part diameter?

A: 13

Q: Match the allowance and limit parameter in

A: Given data; Column given below; Column 1= Allowance and limit paramater Column 2=Quantitative…

Q: a large piece of 1 vo sections: hem cutting m machining jet machining

A: Required  Which is the correct method for cutting of steel plate

Q: When the work done is positive?

A: The work is measured as the energy transfer between to states. Work done is simply the measure of…

Q: reduction in area

A: Given: Initial diameter D=15.55 mmFinal diameter d=7.35 mm TO determine: The percentage reduction in…

Q: If the process mean suddenly shifts to 31.1 psi, what would happen to the percentage of…

A:

Q: Draw the Ts diagram of the whole process

A:

Q: How can a bore be measured?

A: The inner diameter of any cylindrical device is known as bore. The inner diameter of the cylinder is…

Q: What do you mean by Redesign the structure so it is more tolerant of statements

A: Given  Redesign the structure so it is more tolerant of statements To find Meaning of the statement…

Q: = what will be the percentage

A: Given data; mass(m)=2kgharmonic exciting…

Q: Two inward flow to

A: 437 RPM

Q: weight percentage

A: Given; Atomic weight of FE =46that of C is=10We have to find weight percentage of carbon in…

Q: ulties

A: note : according to bartleby guidelines we can solve only first question for you please repost other…

Q: 8M 8 6 WL

A:

Q: bend allowance is

A: Given: Metal sheet thickness is =2 mmIt is to be bent at an angle of one radian,Bent radius is= 100…

Q: 10. For any part of the beam, between two concentrated load Shear force diagram is a Horizontal…

A: For any part of the beam between two concentrated load shear force diagram is a Horizontal straight…

Q: The energy loss due to the immediate increase of pipe diameter a known as a minor loss. Select one:…

A: Given Data⇒ Energy loss due to the sudden increase of pipe diameter among fluid particals.

Q: The minimum possible thickness

A: Given; A thick sheet having 4 mm is rolled with 300 mm diamaterOr, d=300 mm t=4 mmFriction…

Q: what is the change in pipe diameter ca

A: To find Change in pipe diameter caused by internal pressure.

Q: What is the procedure to apply the shear formula?

A: What is the procedure to apply the shear formula?

Q: When the work done is negative?

A: If the displacement of the body is in the direction opposite to the force, then work done is…

Q: 17 in 43 in E

A: refer below images.

Q: e CLA over length L?

A: 2 μm.

Q: Which distance represents height of the fall for measurement of the time?

A: In the question, a machine is given and when it rotates it is needed to find out the height and time…

Q: The clearance ratio of the

A: Given; Reciprocating compressor hahving;  Clearance volume,c=100 mlVolume of the cylinder at BDC is;…

Q: How does a strain gauge work?

A: Strain gauge: It is a sensor whose resistance varies with applied force. It then converts force,…

Q: °C. What is the distance of zero and 30 mark under these conditions?

A:

Q: What are the main uses of the charpy test

A: Charpy test: The Charpy test or the Charpy impact test or the Charpy V-notch test is a toughness…

Q: What about the stretch for OA?

A: There is a mistake in the calculation part for TOA.   Consider the three equations (i), (ii), (iii)…

Q: the minimum metric

A: Given; For the three bolt system shown in the figure,shear yield strength=200 MPaFOS=2The min.…

Q: Isteel rule be

A: detailed Solution given below. leave positive feedback if it helps.

Q: The coefficient of bend value is the energy loss due to bend in a pipe depends on the pipe diameter,…

A: The loss of head due to pipe bend is given by - KV22g where V is average velocity of flow through…

Q: Halp

A: A weld symbol without a flag shows that the weld is to be made within the shop. In more seasoned…

Q: The cause of an induced angle

A: Solution ;

Q: compression.

A:

Q: Table 7.1- values of coefficient of pipe friction (research the table please)

A:

Q: Determine time required/pass?

A: Given; Broach having pitch=5 mm Cut per teeth=0.01 mmReducing the thickness=6 mmlength of the…

Q: Define the term Zero slope?

A: zero slope means a horizontal line which is parallel to the x-axis

Q: What is the approximate % change in the life,

A: Given; Clearance angle=αit is changed from 10 to 7 degreeWhat is the approaximate percentage chnage…

Q: .What is the minimum diameter of the pipe

A: To find Diameter of pipe

Q: Define the Rockwell Scale

A: Rockwell method: It is a hardness testing method that is used to measure the hardness of any metal…

Q: um transverse shear stress and bending

A: