Determine the diameter of the piston rod of the hydraulic cylinder of 100 mm bore when the maximum hydraulic pressure in the cylinder is limited to 11.6 N/mm2. The length of the piston rod is 1.2 m with a yield point value of 300 MPa. The factor of safety may be taken as 2.5 and the end fixity coefficient as 2. Express your answer in mm. Round your answer to 4 significant figures.

Determine the diameter of the piston rod of the hydraulic cylinder of 100 mm bore when the maximum hydraulic pressure in the cylinder is limited to 11.6 N/mm2. The length of the piston rod is 1.2 m with a yield point value of 300 MPa. The factor of safety may be taken as 2.5 and the end fixity coefficient as 2. Express your answer in mm. Round your answer to 4 significant figures.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 17RQ: Convert 22C to Fahrenheit.

See similar textbooks

Similar questions

The hydraulic pump on this forklift can pump fluid at a maximum pressure of 1500 psi (pounds per square inch). If it has to lift a load of 5.0 tons using only one ram, then the diameter of the piston ram must be how many inches big? Round to 2 significant digits.
Convert 22C to Fahrenheit.
PLEASE ANSWER AT FOUR DECIMAL PLACES.I NEED THE ANSWER ASAP. I WILL GIVE YOU A TIP ON PAYPAL IF YOU HELP ME SUBMIT AS EARLY AS POSSIBLE.PLEASE ANSWER AT FOUR DECIMAL PLACES. GIVEN:E = 6 mmF = 536 mmG = 20GpaH = 1.26kN
Q8 The bore diameter of each cylinder in a three-cylinder two-stroke petrol engine is 14.71 mm and the stroke length for each cylinder piston is 250.25 mm. During engine testing, the engine runs at 300 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 6.8 cm2 and area length of length of 2.6 cm. For a pressure scale of 350 kN/m2 per cm on the indicator diagram, calculate the indicated power developed by the engine. Give your answer in kilowatts (kW) to 2 decimal places. Pressure versus Volume Indicator Diagram (Pressure scale = 350 kN/m² per cm) Peak Pressure Enclosed net area for engine work done m.e.p Diagram length, cm Diagram height, cm
X 27. Determine the diameter of the stud bolt that are required to fasten down the cylinder head of a 203 mm x 304 mm gas engine. There are ten bolts on the block. The explosion pressure is 31 kg/sq cm and studs are made of ordinary bolts material SAE 1020. How deep should the bolt be drilled? B. 40.2 mm C. 37.3 mm D. 35.5 mm by a motor at 400 mm raises the attached load of 000 t 28 A. 38.1 mm. A double thread Arme screw driven
Hide AnswerTry Another The formula for piston displacement is P = cd2SN, where c is a constant, d is the cylinder bore, S is the stroke, and N is the number of cylinders. For c = 0.7854, d = 3.000, S = 4, and N = 6, find the piston displacement. (Use the rules for working with measurements to give your answer to the appropriate accuracy and/or precision. Note: The values for S and N are exact numbers. Ignore exact numbers when determining the appropriate accuracy and/or precision.)
A steel pipe has an inside diameter of d = 350 mm and an outside diameter of D = 158 mm. The length of the pipe is L = 5.0 m. The changes in dimension caused by an increase in temperature of 80°C for the: Outside diameter __ mm Inside diameter __ mm Lenght __ mm 3 decimal places
A steel pipe has an inside diameter of d = 350 mm and an outside diameter of D = 158 mm. The length of the pipe is L = 5.0 m. The changes in dimension caused by an increase in temperature of 80°C for the: Outside diameter __ mm Inside diameter __ mm Lenght __ mm 3 decimal places standard coefficient of thermal expansion: steel - 11.25x10^-6 / degrees celcius Aluminum - 23x10^-6 / degrees celcius
In a tensile test for an aluminum alloy, the sample used is 2 inches long and 0.5 inches in diameter. The proportional portion of the tension stress-strain diagram for an aluminum alloy is shown below. _x106 lb/in² Pay attention to units and calculate your answer to 1 decimal place for the unit specified above. σ (ksi) 70 t 0.00614 Determine the modulus of elasticity for this material: € (in./in.)
IS. 03 16. The shaft, as shown in Fig. 14.20, is driven by pulley B from an electric motor. Another belt drive from pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratio of belt tensions for pulley B is 3.5. B. TA2 A D. TA 150 -100- TB2 100 All dimensions in mm. Fig. 14.20 The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable tensile stress for the shaft material is 170 MPa and the allowable shear stress is 85 MPa. Taking torsion and bending factors as 1.25 and 1.75 respectively, find the shaft diameter. Also find out the dimensions for a hollow shaft with outside diameter limited to 30 mm. Compare the weights of the two shafts. Ans. 30 mm : 24 mm: 1.82]
Show complete solutions and figures The diameters of the two cylinders A and B in the figure shown are 80 mm and 750 mm, respectively. The face of the piston is 1.2 m above the face of the weight platform. The space in between the piston and the weight is filled with oil (s.g.=0.80). If F=75 N, Determine the following: the value of Wrequired to maintain equilibrium. a) 38.6 N b) 86.3 N c) 63.8N d) 83.6 N e) None
along The 2-1b block is released from rest at A slides down along the smooth cylindrical surface. The attached spring has a stiffness k =3 lb/ft (Figure 1) Figure 2 ft Gwwwwwww 1 of 1 Provide