The 50-N block is originally at rest on the smooth surface. It is acted upon by a radial force of 10 N and a horizontal force of 35 N, always directed at 30 degrees from the tangent to the path as shown. Determine the time, t, required to break the cord, which requires a tension Tmax N. What is the speed of the block, vg, when this occurs? Neglect the size of the block for the calculation. Complete the table by filling in the values in the yellow cells. 1.2 m 35 N 300 10 N Table 7 |Tmax (N) Vв (m/s)| г (s) 250

The 50-N block is originally at rest on the smooth surface. It is acted upon by a radial force of 10 N and a horizontal force of 35 N, always directed at 30 degrees from the tangent to the path as shown. Determine the time, t, required to break the cord, which requires a tension Tmax N. What is the speed of the block, vg, when this occurs? Neglect the size of the block for the calculation. Complete the table by filling in the values in the yellow cells. 1.2 m 35 N 300 10 N Table 7 |Tmax (N) Vв (m/s)| г (s) 250

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A motorboat and its load weigh 2150 N. Assume that the propeller force is constant and equal to 110N, and the water resistance is numerically equal to 6.7V, where V is the speed at any instant time in m/sec. If the boat starts from rest, determine its distance at the end of 10 seconds.
A motorboat and its load weigh 2150 N. Assume that the propeller force is constant and equal to 110N, and the water resistance is numerically equal to 6.7V, where V is the speed at any instant time in m/sec. If the boat starts from rest, determine its speed at the end of 10 seconds.
A 200 N block slides from rest down a plane inclined 25° to the horizontal. Assuming =0.20, what will be the speed of the block after 5 seconds?
Determine the speed of block in Q1 when it moves 2m up the slope using the Work and Energy method and calculate the power of the force P. (If you can apply the principle of work and energy or conservation of enegry.) Plus can you not use the required method for this question. Question 1: A 5kg block is pushed up along the slope as shown. The coefficient of kinetic friction is uk =0.2. Determine the speed of the block when it moves 2 m up the slope using Newton's Second Law. I also gave the answer for Q1 if it helps: V = 2.21m/s
1) A cable is attached to a 0.5 kg block that slides over the smooth rigid horizontal rod AB. The diagram shown depicts the vertical plane. The cable tension is constant value T. At point C the speed of the block is 6 m/s to the left and at point D the speed is 1 m/s to the left. Determine the value of T. Note: take gravitational acceleration g=9,806 3 m D C A 4 m-
Q. In Figure, a block slides along a path that is without friction until the block reaches the section of length L=0.85 m, which begins at height h=2.0 m on a ramp of angle 0-45°. In that section, the coefficient of kinetic friction is 0.40. The block passes through point A with a speed of 8.0 m/s. If the block can reach point B (where the friction ends), what is its speed there, and if it cannot, what is its greatest height above A? A. 8.9 m/s B. 6.9 m/s C. 4.9 m/s D. 2.9 m/s E. 1.9 m/s Lütfen birini seçin.
ft A 10 lb block has an initial speed of v = 4 . A force of F = 8 · t lb is applied. The coefficient of kinetic friction between the block and surface is u = 0.2. V1 F = f(t) Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value 30 ft Using equations of motion in rectangular coordinates, a. Find an equation for the block's horizontal acceleration as a function of t, a(t), when the block moves s = 30 ft. b. Find an equation for the block's velocity as a function of t, v(t) , when the block moves s = 30 ft. c. Determine the time it takes for the block to move s = 30 ft. i. Use a solver/graphing calculator to solve for the Quartic Function d. Determine the velocity of the block at s = 30 ft. %3D
A roller coaster starts from rest at A, rolls down the track to B, describes a circular loop of 40-ft diameter, and moves up and down past Point E. Take h=74 ft and assume that there is no energy loss due to friction. D = 20 ft C B Determine the force exerted by his seat on a 195-lb rider at B and D. lb. ↑ The force exerted by seat on the rider at Bis The force exerted by seat on the rider at Dis lb. ↓
b)With the radius of curvature (r) at the top of the loop (T) is 1 m. Determine the minimum speed (in m/s) of the box required at point T such that it can stay on the loop.
Q1 [Type B]: The 20-lb crate A rests on a smooth surface. If the crate starts from rest and P = (t² + 1.5t) lb where t is in seconds, determine the speed of the crate A at t = 2 s using the method of linear impulse and momentum. Not using the required method would result in a 0 for this question. A Shaobo Huang P 30⁰
The ski and the rider, with a total mass of 90 kg, are moving along the curved path. Since the equation of the curvilinear path is determined as y = 0.08x2 and the speed at x = 10 m is known as 5 m / s, find the value of a) the rate of increase in the speed of the skier at this point, b) the normal force applied to skiing.
Under the man's pushing force P= 30.8 lb, the uniform cabinet is sliding on the ground with a constant acceleration of a. If the uniform cabinet has weight of 150 lb, and the coefficient of kinetic friction between the cabinet and the ground is Uk 0.14, determine acceleration a in ft/s2. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 32.2 ft/s². -1 ft→1 ft→ P G 4 ft 3.5 ft В Your Answer: Answer