28. A locomotive coupling rod, 2-5 m between centres, is of symmetrical I- section: the outside dimensions are: 40 mm wide by 120 mm deep, web, 14 mm thick and flanges each 20 mm thick. Find the maximum compressive stress in the rod due to an end thrust of 150 kN and a uniform transverse load of 5 kN/m. E = 200 GN/m2. (U. Lond.) (Ans.: 111-4 MN/m²)

28. A locomotive coupling rod, 2-5 m between centres, is of symmetrical I- section: the outside dimensions are: 40 mm wide by 120 mm deep, web, 14 mm thick and flanges each 20 mm thick. Find the maximum compressive stress in the rod due to an end thrust of 150 kN and a uniform transverse load of 5 kN/m. E = 200 GN/m2. (U. Lond.) (Ans.: 111-4 MN/m²)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.3P: A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the...

See similar textbooks

Similar questions

Solve the preceding problem for a W 200 × 41,7 shape with h = 166 mm, h = 205 mm. rw = 7.24 mm, tE= ILS mm,andV = 38 kN.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
28. A locomotive coupling rod, 2-5 m between centres, is of symmetrical I- section: the outside dimensions are: 40 mm wide by 120 mm deep, web, 14 mm thick and flanges each 20 mm thick. Find the maximum compressive stress in the rod due to an end thrust of 150 kN and a uniform transverse load of 5 kN/m. E = 200 GN/m2. (U. Lond.) (Ans.: 111-4 MN/m²)
The circular shaft shown is subjected to an axial force P at its free end and a compressive force of 50 kips at point B. Note that the shaft is hollow between points A and B. The allowable normal tension stress is 22 ksi, the modulus of elasticity is 29,000 ksi, and the maximum allowable elongation is 0.04 in. Determine the maximum allowable value of P in kips. -0.75 in A >50 kips 3 in 20 in 30 in
A steel torsion bar AB with diameter d = 34 mm, and ductile material of tensile yield strength Sy = 276 MPa is attached to a rigid arm at A, supported by a bearing at C, and fixed at B, as the picture shows. At the right end of the arm is mounted the wheel on which the vertical force P acts from the ground and which passes through the center of the wheel. If bearing C acts as a simple support and the effect of transverse shear due to P is negligible, determine the maximum force P (in kN) that can be applied to the wheel. Consider a factor of safety n = 2.5. Use the maximum energy of distortion failure criterion and do the analysis on bar AB (torsion bar) in the section where the bearing is.
The inner diameter of a cylindrical pressure vessel is 400 mm. When subject to pressure, the hoop stress in the cylinder wall is 40 MPa. For the material of construction E = 200 GPa and Poisson's ratio = 0.3. The %3D increase in inner diameter is, O a. 0.016 mm b. 0.08 mm O c. 0.068 mm O d. 0.04 mm
the cröss-stCtions e-e and f-f, respectively, when a torque T = 800 Nm is applied at point B. Take the shear modulus G= 80 GPa. Qier te cruhe The stepped shaft shown below is rigidly attached at both ends. The shaft segments AC and CD have (a) Find the reactions at both ends. (b) Determine the shear stress developed at points K and L on a cross-section taken from the shaft between points B and C. (c) Find the angle of twist at point C. 30 mm T=800 N.m 20uun 50 mm Activate Windou Section ffSings 200 mm 400 mm 300 mm Section e-e
A 0.5 m-long metal composite shaft AB consists of a steel rod (radius r=25 mm), the outer surface of which is bonded to the inner surface of an aluminum tube (outer radius ro=37.5 mm). The shaft has the geometry and cross section shown below. One end (B) of the shaft is fixed onto a rigid wall while the other end (4) is subjected to an external torque T₁=350 N-m. Take Gst=78 GPa for the steel rod and GAI-28 GPa for the aluminum tube. osiquicl edt yd (2) alum. A B 0 TA A (1) steel Cross section Figure 2.1. Composite shaft with external torque TA (a) Find the angle of twist at A (OA) due to TA. (b) Find the maximum shear stress in the steel rod. (c) Find the maximum shear stress in the aluminum tube. (d) If the allowable angle of twist is (A) allow=10³ rad, determine the maximum length the shaft can have when subjected to TA=350 N-m at the free end.
The rod shown below is of diamater 70 mm and is fixed at one end. It is subjected to 500 N.m and 300 N.m torsional moments as shown. Sketch the distribution of the internal torsional moment along the length of the rod. Also find the torsional shear stress at points A and B, and also the largest shear stress in the rod. Point B is to the left of the 500 N.m torsional moment and A is on the right of it. Round-up your answers to the nearest 1/100th of an MPa. y 35 mm 20 mm 500 N.m 35 mm- 300 N.m Torsional shear stress at A = MPа %3D Torsional shear stress at B = MPа Maximum shear stress = MPa %3D
The bar shown is subjected to a moment of 6000 lb.in. Calculate the maximum stress developed in the bar. D. Given : D = 2 in, d = 1 in, h = 0.5 in ,r = 0.25 in Select one: a. Omax = 102.18 ksi O b. Omax = 147.07 ksi O c. Omax = 72.00 ksi O d. Omax = 126.06 ksi Clear my choice
The inner diameter of a cylindrical pressure vessel is 400 mm. When subject to pressure, the hoop stress in the cylinder wall is 40 MPa. For the material of construction E = 200 GPa and Poisson's ratio = 0.3. The increase in inner diameter is, O a. 0.08 mm O b.0.04 mm O. 0.068 mm Od.0.016 mm
A copper tube with circular cross sectionhas length L = 1.25 m, thickness t = 2 mm, andshear modulus of elasticity G = 45 GPa. The bar isdesigned to carry a 300 N ? m torque acting at theends. If the allowable shear stress is 25 MPa and theallowable angle of twist between the ends is 2.5°, whatis the minimum required outer diameter d?