1) The throttle-control sector pivots freely at O. If aninternal torsional spring exerts a return momentrests against the idle-control adjustment screw at R.M=2 N.m on the sector when in the positionthrottle-cable tension T so that the net momentabout O is zero. Note that when T is zero,shown, for design purposes determine the necessary50 mmthe sectorAns. T 40 N

Answered: Image /qna-images/answer/4b4d6a3d-9248-4dfb-9914-772eba84f8e1.jpg

1) The throttle-control sector pivots freely at O. If an internal torsional spring exerts a return moment M= 2 N.m on the sector when in the position throttle-cable tension T so that the net moment shown, for design purposes determine the necessary 50 mm hout O is zero. Note that when T is zero, the sector usts against the idle-control adjustment screw at R. Ans. T 40 N

1) The throttle-control sector pivots freely at O. If an internal torsional spring exerts a return moment M= 2 N.m on the sector when in the position throttle-cable tension T so that the net moment shown, for design purposes determine the necessary 50 mm hout O is zero. Note that when T is zero, the sector usts against the idle-control adjustment screw at R. Ans. T 40 N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.24P

See similar textbooks

Similar questions

Equilibrium of Concurrent Force System. The piston of a reciprocating engine exerts a force of 175 kN on the crosshead when the crank is 45° (angle B) past TDC. If the stroke of the piston is 800 mm and the length of the connecting rod is 1.80 m, find the guide force and the force in the connecting rod. Hint: 1=½ stroke; Angle o may be solved using Sine Law in AACO. K= Compressive Force in the connecting Rod E= Piston Effort 70 120 F, = Guide Force Fig. P-1 Fig. P-2 a Tools: EF cos0=0; F sin .=0. R = Ev)* + (E#): ; R 771 =- : tane = sin A sin B sin C
Determine the equivalent spring stiffness of the system using the displacement of the block as the generalized coordinate
5. For the following 4-bar mechanism, determine torque T₂ (in terms of T4) to keep the system in static equilibrium. Link lengths are a₁ a2 a3 and a4 03 0₂ 3 D 1 44
Crank connecting rod in Figure-1crank and connecting rods in the mechanismare the same length; AB = BC = L andBF=FC. One end to point B, the otherfrictionless with the tip horizontally.connected to movable point Dthe stiffness of the spring is k (N/m) when =90the spring is not elongated. spring mechanismforce, R1 and R2 forces and Mstatic under the influence of momentis in balance. The principle of virtual worksstatic balance of the mechanism by applyinggiving the theta angle corresponding to the positionget a relation andthe last of your student number from the table.appropriate values according to the numberCalculate the theta angle using M= -400Nm R1=300N R2=200N L=1,3m k=500N/m
The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V- belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=90ON), coefficient of friction u=0.3 4- the speed of large pulley.
Question 2: The ideal spring of constant k-2.6 kN/m is attached to the disk at point A and the end fitting at point B, as shown. The spring is unstretched when OA and Oв are both zero. If the disk is rotated 15° clockwise and the end fitting is rotated 30°counterclockwise, determine the vector expression for the spring force F. ( Determine distance C so that the moment the spring force makes about the Z axis is equal to 10.82 N.m. ( A = 15°. C A 250 mm eeeeeee 900 mm k= 2.6 kN/m OB = 30° B LC 7-y 200 mm
Introductory Problems 4/65 Determine the magnitudes of all pin reactions for the frame loaded as shown. Ans. A = 512 N, B = D = 1013 N 800 N 4/68 Determine the 300 each member o mm 650 P mm A 30° 60° Problem 4/65 OIV / MA
A shaft carries three pulleys, A, B and C, the pulleys B and C being 1.2 m and 2.1 m from A. The pulleysare out of balance to the extent of 0.03, 0.05 and 0.04 kg-m respectively and are keyed to the shaft so asto give static balance. Find the relative angular positions of the radii which define the unbalance. If theshaft is supported in bearing 1.8 m apart, find the dynamic load on each bearing when the shaft makes300 rev/min.
3. Position of W3 with W1 at the 1 cm mark. 1 cm C.g = cm cm www W1 W3 Note:W1 is lighter than W3 Write a torque equation of the system
1. In lecture I focused on a horizontal mass-spring system so we could ignore gravity, but in practice it's much easier to build a vertical mass-spring system. In the figure below, we can see a suspended spring with spring constant k both before and after a mass m is hooked to it. Y Yo yo is the equilibrium height of the spring (without the mass) and in the figure y = 0 is set at the ground. a) Using the coordinate system in the figure, show that Newton's second law for the hanging mass-spring system leads to the following differential equation: d²y dt² k (y - Yo) - g m b) Now define a new coordinate, y', related to y by a constant shift: y = y' + C, where C = constant. Show that if you choose the right value of C, Newton's second law is identical in form to a mass-spring system without gravity. What is the period of the system? c) Effectively, gravity just shifts the equilibrium position of the system, but the system still undergoes simple harmonic motion. What is the net force on the…
Find the torque on link 2 necessary to maintain static equilibrium for the 4-bar mechanism shown below. Use analytical method, draw free body diagram of each link. O,A = 3.5 in., AB = 0,B = 6 in., O,C = 7 in. P.=50 lb 4 -152. 105 240° M12 2
Question 2: The ideal spring of constant k-2.6 kN/m is attached to the disk at point A and the end fitting at point B, as shown. The spring is unstretched when OA and Oв are both zero. If the disk is rotated 15° clockwise and the end fitting is rotated 30°counterclockwise, determine the vector expression for the spring force F. Determine distance C so that the moment the spring force makes about the Z axis is equal to 10.82 N.m. - A = 15°1 A 250 mm lllllll 900 mm k = 2.6 kN/m OB = 30° B G 200 mm