Suppose 85 mL of a buffer solution that was 0.15 M HCHO2 and 0.25 M NaCHO₂ had 7.5 mL of 0.10 M hydrochloric acid added to it. Afterwards, 35 mL of this mixture was measured out, placed inside an Erlenmeyer flask, and diluted to 75 mL. What was the concentration of the hydroxide ion in the resulting solution in the flask? Ka for HCHO2, formic acid, is 1.7 x 10-4. a. 9.80 x 10-11 M b. 2.81 x 10-7 M c. 2.55 x 10-9 M d. 8.94 x 10-11 M 210 x 10-10 M P

Suppose 85 mL of a buffer solution that was 0.15 M HCHO2 and 0.25 M NaCHO₂ had 7.5 mL of 0.10 M hydrochloric acid added to it. Afterwards, 35 mL of this mixture was measured out, placed inside an Erlenmeyer flask, and diluted to 75 mL. What was the concentration of the hydroxide ion in the resulting solution in the flask? Ka for HCHO2, formic acid, is 1.7 x 10-4. a. 9.80 x 10-11 M b. 2.81 x 10-7 M c. 2.55 x 10-9 M d. 8.94 x 10-11 M 210 x 10-10 M P

Chemistry

9th Edition

ISBN:9781133611097

Author:Steven S. Zumdahl

Publisher:Steven S. Zumdahl

Chapter15: Acid-base Equilibria

Section: Chapter Questions

Problem 7ALQ: You have a solution of the weak acid HA and add some HCl to it. What are the major species in the...

See similar textbooks

Similar questions

A buffer is prepared in which the ratio [ H2PO4 ]/[ HPO42 ]is 3.0. (a) What is the pH of this buffer? (b) Enough strong acid is added to convert 15% of HPO42- to H2PO4-. What is the pH of the resulting solution? (c) Enough strong base is added to make the pH 7.00. What is the ratio of [H2PO4-] to [HPO42-] at this point?
Sketch the titration curve for a weak acid titrated by a strong base. When performing calculations concerning weak acidstrong base titrations, the general two-slep procedure is to solve a stoichiometry problem first, then to solve an equilibrium problem to determine the pH. What reaction takes place in the stoichiometry part of the problem? What is assumed about this reaction? At the various points in your titration curve, list the major species present after the strong base (NaOH, for example) reacts to completion with the weak acid, HA. What equilibrium problem would you solve at the various points in your titration curve to calculate the pH? Why is pH 7.0 at the equivalence point of a weak acid-strong base titration? Does the pH at the halfway point to equivalence have to be less than 7.0? What does the pH at the halfway point equal? Compare and contrast the titration curves for a strong acidstrong base titration and a weak acidstrong base titration.
8-71 Explain why you do not need to know the chemical formula of a buffer compound to use it.
A friend asks the following: Consider a buffered solution made up of the weak acid HA and its salt NaA. If a strong base like NaOH is added, the HA reacts with the OH to form A. Thus the amount of acid (HA) is decreased, and the amount of base (A) is increased. Analogously, adding HCI to the buffered solution forms more of the acid (HA) by reacting with the base (A). Thus how can we claim that a buffered solution resists changes in the pH of the solution? How would you explain buffering to this friend?
8-55 We commonly refer to a buffer as consisting of approximately equal molar amounts of a weak acid and its conjugate base—for example, CH3COOH and CH3COO-. Is it also possible to have a buffer consisting of approximately equal molar amounts of a weak base and its conjugate acid? Explain.
Phenol, C6H5OH, is a weak organic acid. Suppose 0.515 g of the compound is dissolved in enough water to make 125 mL of solution. The resulting solution is titrated with 0.123 M NaOH. C6H5OH(aq) + OH(aq) C6H5O(aq) + H2O() (a) What is the pH of the original solution of phenol? (b) What are the concentrations of all of the following ions at the equivalence point: Na+, H3O+, OH, and C6H5O? (c) What is the pH of the solution at the equivalence point?
. Which component of a buffered solution is capable of combining with an added strong acid? Using your example from Exercise 60, show how this component would react with added HC1.
Explain why equilibrium calculations are not necessary to determine ionic concentrations in solutions of certain strung electrolytes such as NaOH and HCl. Under what conditions are equilibrium calculations necessary as part of the determination of the concentrations of all ions of some other strong electrolytes in solution?
Define a buffer solution. What makes up a buffer solution? How do buffers absorb added H+ or OH with little pH change? Is it necessary that the concentrations of the weak acid and the weak base in a buffered solution be equal? Explain. What is the pH of a buffer when the weak acid and conjugate base concentrations are equal? A buffer generally contains a weak acid and its weak conjugate base, or a weak base and its weak conjugate acid, in water. You can solve for the pH by setting up the equilibrium problem using the K.a reaction of the weak acid or the Kb reaction of the conjugate base. Both reactions give the same answer for the pH of the solution. Explain. A third method that can be used to solve for the pH of a buffet solution is the HendersonHasselbalch equation. What is the HendersonHasselbalch equation? What assumptions are made when using this equation?
8-93 Do a 1.0 M CH3COOH solution and a 1.0 M HCI solution require the same amount of 1.0 M NaOH to hit a titration end point? Explain.
Determine the dominant acid-base equilibrium that results when each of the following pairs of solutions is mixed. Indicate the equilibrium by writing 1 for a strong acid, 3 for a weak acid, 4 for an acidic buffer, 7 for a neutral solution, 10 for a basic buffer, 11 for a weak base, and 13 for a strong base. (a) 10.0 mL of 0.15 M NaOH + 15.0 mL of 0.10 M HNO3 (b) 25.0 mL of 0.10 M HCl + 10.0 mL of 0.25 M NH3 (c) 50.0 mL of 0.050 M NaOH + 50.0 mL of 0.10 M NH3 (d) 50.0 mL of 0.10 M NH3 + 50.0 mL of 0.05 M HCl
A 25.0-mL sample of hydroxylamine is titrated to the equivalence point with 35.8 mL of 0.150 M HCl. a What was the concentration of the original hydroxylamine solution? b What is the pH at the equivalence point? c Which indicators, bromphenol blue, methyl red, or phenolphthalein, should be used to detect the end point of the titration? Why?