Structural analysis *answer question 3 Q1) Determine the horizontal and vertical components of reaction at the pins A, B, and C.10 kN/m4 mAQ2) Determine the horizontal and vertical components of reaction at pins A, B, and Cof the two-member frame.300 lbB-24-24-ft6kNB4 ft45°2 m2m2 mB2 mㄱ2 mCQ3) Determine the components of reaction at the roller support A and pin support C. Joint B is fixed connected.3 ft2 kN

Answered: Image /qna-images/answer/29a1d771-96bc-4c17-af59-b91b7fb4cfaa.jpg

Answered: Q3) Determine the components of…

Q3) Determine the components of reaction at the roller support A and pin support C. Joint B is fixed connected. 2 m- 6 kN 2 m B 2 m 2 m 2 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the frame shown, members 'ACE' and 'BCD' are connected by a pin at 'C' and by the link 'DE'. For the loading shown, determine the: A 160 mm 449 N 60 mm 80 mm E -150 mm- 60 mm 100 mm 1) Reaction at 'B' in N. 2) Force in link 'DE' in N. 3) Horizontal component at 'C' on member 'BCD' in N. 4) Vertical component at 'C' on member 'BCD' in N. 5) Total force exerted at 'C' on member 'BCD' in N.
Q2-B- Fill in the blank with the correct answer. KS) 1. When the resultant of force system acting on a body is zero, the body is said to be in (a) rotating condition (d) dynamic condition (b) translation condition (c) equilibrium condition 2. Number of component of reaction at hinge support are (a) zero (b) one (c) two (d) three 3. The angle that the vector A-2i+3j makes with y-axis is 4. If angle made by the force with y and z axes are 0,= 60° and 0,= 45° then 0, 5. Force is completely defined by its (a) magnitude (b) direction (c) point of application (d) All of these
Q5/A) From the figure below, determine the reaction force at pin C. A 000 0.6 m 10 kN 0.6 m 0.8 m 60° 0.4 m 6 kN OB
4.8 m 2. The frame shown below is loaded with an unknown horizontal force, P. At point E, the surface exerts a force of 130 lb. on the roller. a) Draw and label all the reactions and forces acting on the frame and on the individual components, using the diagrams provided on the back of this handout. b) Determine the magnitude of the force, P, required for the frame to be in equilibrium. c) Determine the x- and y- components of the force acting at point C on member CDE, and specify the directions (→, +, t. 1). Note: For each calculation, state which diagram number (1, 2, 3, 4) you are using. Ans: P = 80 lb, C = 100 lb , C, = 75 lb 1 (by the way, FBC = 125 lb (T)) 4 in. 8 in. C 3 in. В 6 in. 1 3
(question 1) P = 75 lb. The pin at C is attached to member ABCD and passes through the smooth slot in member ECF. Part A) Determine the horizontal and vertical components of force that the pin A exerts on member ABCD. Part B) Determine the horizontal and vertical components of force that the pin B exerts on member ABCD. Part C) Determine the horizontal and vertical components of force that the pin C exerts on member ABCD.
Question 2 Find the value of The reaction force at the support A. (X,XX,XXX represents the last digits number pf your IC) 4m 400 KN 10 m B 60 KN 4m 10 m. 157KN 4m 17 m D
A) Determine the force in the spring with unstretched length 3 inches and a spring constant of 240 lb/ft. B) Determine the forces at A, B, C, D, and F. A 6 in. B 6 in. D 6 in. E G 8 in. 8 in.
4 in- 4 in- 20 lb 40 lb B 2 in. 3 in. 3 in. E 1. The bracket is supported by pegs at C and D and a roller at E. Ignore friction and use 0 = 30°. a) Replace the applied forces with a single equivalent applied force and specify the distance x from A along AB where the equivalent force must apply b) Draw the free body diagram for the bracket c) Solve for the reactions at C, D and E.
Take P = 840 lb A)Determine the horizontal and vertical components of force that the pin C exert on member ECD of the frame. B)Determine the horizontal and vertical components of force that the pin D exert on member ECD of the frame.
TRUSS PROBLEM Determine:a) The magnitude and direction of the reactions at 3 and 5b) The forces in each member of the truss and determine if the truss is being subjectedto a compressive or tensile force. answers: a)R3 = 75 vertically upwards, R5 = 25 vertically upwardsb)F1-2 = -29, F1-3 = -87, F1-4 = -29, F2-4 = +29, F2-5 = -29, F3-4 = +43, F4-5 = +14 please show all workings
The blade of the bulldozer shown below is rigidly attached to a linkage consisting of the arm AB, which is controlled by the hydraulic cylinder BC. There is an identical linkage on the other side of the bulldozer. Applied loads shown are for both linkages and F = 661 kN. a) Determine the magnitude of the pin reaction at A in kN. b) Determine the magnitude of the pin reaction at B in kN. c) Determine the magnitude of the pin reaction at C in kN. d) Determine the pressure in hydraulic cylinder BC in Pa if the cylinder has a diameter of 80 mm.
1. Figure Q1 shows an illustration of a bell crank mechanism that is in a state of static equilibrium. It is hinged at B and has a force of 200 N applied at the end c at 30° to the horizontal direction as shown in the Figure. The angle 0 made by the force F at the end A is 55°. a) Draw the free body diagram for the crank ABC b) Determine the force F at the joint A c) Determine the resultant force on the pin at B and its direction. d) Determine the magnitude of the force F and the angle 0 for which the resultant force at the joint B will be aligned along the vertical direction. 30° 30 A B 200 N 100 50 All dimensions in mm F