An air compressor is driven by a 7.5 HP electric motor with a speed of 1750 rpm with A-60 V-belts of length 73.65 in. The pitch diameter of the small pulley is 110mm and the larger pulley is 224mm. Service factor is 1.2. Determine the arc of contact of the (a) smaller pulley and (b) larger pulley in degrees. Express your answer in 3 decimal places.

An air compressor is driven by a 7.5 HP electric motor with a speed of 1750 rpm with A-60 V-belts of length 73.65 in. The pitch diameter of the small pulley is 110mm and the larger pulley is 224mm. Service factor is 1.2. Determine the arc of contact of the (a) smaller pulley and (b) larger pulley in degrees. Express your answer in 3 decimal places.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A machine shaft turning at 600 rpm is supported on bearings 20" apart. Twenty HP is supplied to the shaft through a 20" pulley located 10" to the right of the right bearing. The power is transmitted from the shaft through an 8" spur gear located at the middle of the two bearing. The pulley weighs 300 lb to provide some flywheel effect. The forces acting on the pulley and the gear are given in the diagram. The shaft material selected has an ultimate strength of 70,000 psi and a yield stress of 46,000 psi, determine: Reactions at the bearings b. Bending moment diagrams in the horizontal and vertical directions а. C. The necessary diameter in accordance with the ASME Code using Kb =1.5 and Kt = 1.5. %3D Pulley Mt 525 lb Gear 191 lb Mt 10" 10" 10" Forces on Gear 348 lb W=300 lb 116 lb
Two parallel shaft 6 m apart are provided with 900 mm and 300 mm diameter pulleys and are connected by means of a cross belt .The Direction of rotation of the follower Pulley is to be reversed by changing over to an open belt drive. How much length of the belt has to be reduced.
A shaft turning 200 RPM is to drive another shaft at 250 RPM connected in open belt. Find the diameters of the two pulleys, using integral number of inches for each diameter, to give as nearly as possible a belt speed of 3500 FPM.
Determine the belt length of a V-Belt drive used to connect the 8 cm and 14 cm pulley at a center distance of 50 cm
Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and the output shaft should be capable of running at speeds of 950 rpm, 650 rpm, 450 rpm, 250 rpm, and 150 rpm. If the diameter of the smallest pulley on the driven shaft is 2 inches, calculate the length of the belt and the diameters of each pulleys attached at the shafts.
A 220 mm diameter of 14.5 degrees involute gear is used to transmit 50 kW at 580 rpm Find the total force transmitted on the gear.
Two shafts 30 in. apart, each carrying a four-step pulley, are to be connected by a cross belt. The driving shaft is to turn 180 rpm while the driven shaft is to turn 50, 150, 250, and 600 rpm. The smallest step of the driver is 10 in. in diameter. Find (a) the diameters of all the steps, (b) angle of contact for each pair of pulleys, and (c) belt length.
An electric motor drives a flat-belt pulley at a shaft speed of 1750 rpm. The 600 mm wide Polyamide F-2 belt driven at a speed of no more than 17.5 m/s is used to drive a second shaft over a distance of 5 m at a maximum shaft speed of as close to 900 rpm as possible. The system requires a service factor of 1.2. Using the abovementioned information to calculate the following and submit the answers online. a. the configuration required to satisfy the speed requirements using commercial pulleys b. the maximum nominal power rating of the motor when driving the belt under light shock conditions c. the pre-tension required to prevent slippage d. the required belt length and e. the dip in the belt.
Please solve ellaborately using the equation provided in the figure and include the untis in every step, show diagram and write your solutions clearly and readable if your solution is in written form. Your work will be appreaciated much. Thank You. Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and the output shaft should be capable of running at speeds of 950 rpm, 650 rpm, 450 rpm, 250 rpm, and 150 rpm. If the diameter of the smallest pulley on the driven shaft is 2 inches, calculate the length of the belt and the diameters of each pulleys attached at the shafts.
Compute the torque (Nm) on a shaft transmitting 750 W of power while rotating at 1750 revolutions per minute.
The diagram below shows a shaft with spur gear (B), bevel gear(D), and two supporting bearings (A and C). All dimensions are in millimeters and all shoulder fillets (at points where diameter changes) have a radius of 4.4 mm. The pressure angle for the spur gear at B is 16 °. The pressure angle for the bevel gear at D is 18° and the bevel angle is 45°. Note that the shaft is designed so that only bearing A takes thrust. The shaft is made of steel with Su= 1060 MPa. All the critical surfaces are ground. The shaft rotates at 1820 rpm. A motor with a power of 650 kW is connected at the bevel gear through another bevel gear. This drives the shaft. A load is connected through another spur gear at the output spur gear at B. The standard deviation on the power is 60 kW. (a) Determine the forces acting on the gears. Recall that for a spur gear, the relation between the tangential component of the force and the radial component of the force and the pressure angle is given by F₁ = F₂.tan(o). For…
4. A machine shaft turning at 600 rpm is supported on bearings 30" apart. Twenty HP is supplied to the shaft through an 18" pulley located 10" to the right of the right bearing. The power is transmitted from the shaft through an 8" spur gear located 10" to the right of the left bearing. The pulley weighs 200 lb to provide some flywheel effect. The forces acting on the pulley and the gear are given in the diagram. The shaft material selected has an ultimate strength of 70,000 psi and a yield stress of 46,000 psi, determine: Reactions at the bearings b. Bending moment diagrams in the horizontal and vertical directions a. The necessary diameter in accordance with the ASME Code using Kh=1.5 and Kt = 1.0. points) с. Pulley Mt 525 lb Gear 191 lb Mt Forces on Gear 10" 20" 10" 348 lb W-200 lb 116 lb