Problem 5: Given a Crucible with a base diameter (Din)of 8 mm and the length (L) of the attached half pipe is 10 mm and the height (H) of the crucible is 16 mm. If initially the Crucible is filled to the half with water and we tilt or incline this crucible with angle a until it begins to flow out of the shown structure. Calculate the volume flowrate of the water and the time to be empty. Note: if there is any missing parameter or information you can Assume it and solve the problem. Din Upright position tilted position

Problem 5: Given a Crucible with a base diameter (Din)of 8 mm and the length (L) of the attached half pipe is 10 mm and the height (H) of the crucible is 16 mm. If initially the Crucible is filled to the half with water and we tilt or incline this crucible with angle a until it begins to flow out of the shown structure. Calculate the volume flowrate of the water and the time to be empty. Note: if there is any missing parameter or information you can Assume it and solve the problem. Din Upright position tilted position

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Show the step by step solution. Thank you. 3. A pump draws water from reservoir A and lifts it to reservoir B as shown in Figure 4-10. The loss of head from A to 1 is 3 times the velocity head in the 150-mm pipe and the loss of head from 2 to B is 20 times the velocity head in the 100-mm pipe. Compute the horsepower output of the pump and the pressure heads at 1 and 2 when the discharge is: (a) 12 L/s (b) 36 L/s
URGENT Please answer this problem in 30minutes. I need correct answers with complete and step by step solution. Box the final answers. Do not shortcut your solution. I will give an upvote if it satisfies. Thank you! If the velocity of water is 8 m/s and the pressure is 140 kPa on the discharge side of a pump. a. What is the head of the pump if the velocity is 4 m/s and the pressure is 90 kPa on the suction side of the pump? b. How much power is required to drive it if the diameter of the suction side is 600mm? c. If the pump is rated at 120hp, what is the efficiency of the pump neglecting energy losses in the system?
At a certain temperature, water rises inside 0.10in diameter capillary tube. How high will it rise if the wetting angle is zero and the surface tension is 0.005 lb/ft? Select the correct response: O 0.832 in 0.654 in O 0.426 in O 0.232 in
Transcribed Image Text:As part of a processing of biofuels, water is pumped into a circular tank with a diameter Dt. as shown in Figure Q3. The flowrate into the tank is Q₁ and the flowrate out is Q₂. When the vessel is heated, water evaporates. The average velocity at which the vapour rises across the entire tank is vevap- You may assume that water has a density of Pw, and vapour has a density of Pv. Acceleration due to gravity is g. 2₁ Vevap Q₂ => D₂ Figure Q3: Water being pumped through a heated evaporation tank. Find anexpressio for the rate of chnage of the mass of water in the tank At time t= 0 the height of water in the tank is h0. Find an expression for the height as a function of time h(t) An alarm is triggered when the pressure at the bottom of the tank exceeds P alarm. Find an expression for the time at which the alarm goes off
1. A pump (Figure 4-07) takes water from a 200-mm suction pipe and delivers it to a 150-mm discharge pipe in which the velocity is 2.5 m/s. At A in the suction pipe, the pressure is -40 kPa. At B in the discharge pipe, which is 2.5 m above A, the pressure is 410 kPa. What horsepower would have to be applied by the pump if there were no frictional losses?
1. A pump (Figure 4-07) takes water from a 200-mm suction pipe and delivers it to a 150-mm discharge pipe in which the velocity is 2.5 m/s. At A in the suction pipe, the pressure is -40 kPa. At B in the discharge pipe, which is 2.5 m above A, the pressure is 410 kPa. What horsepower would have to be applied by the pump if there were no frictional losses? 2. A pump (Figure 4-07) takes water from a 200-mm suction pipe and delivers it to a 150-mm discharge pipe in which the velocity is 3.6 m/s. The pressure is -35 kPa at A in the suction pipe. The 150 mm pipe discharges horizontally into air at C. To what height h above B can the water be raised if B is 1.8 m above A and 20 hp is delivered to the pump? Assume that the pump operates at 70 percent efficiency and that the frictional loss in the pipe between A and C is 3 m.
The piping system shown in the figure is to move ethylene glycol at a flow rate of 50 gpm. Follow the suggested design procedure and select a suitable pipe size and pump for the system. A B A: Globe valves (2 of them) B: Union fittings (4 with 2 not shown) C: Plate welded to tank to suppress air entrainment in pump inlet D: Elbows: there are five 90° elbows and two 45° elbows The pipe is all wrought iron, with threaded fittings, schedule 40. Pipe lengths total 35.36 m. Total inlet pipe length from tank to pump is 1.22 m. z1 = 1.22 m and z2 = 3.66 m.
Draw the right diagram for the problem. Show complete solution. Water at 60 F from a lake through 500 ft if 4in ID cast iron pipe at a water turbine 250 ft below the surface of the lake. After flowing from the turbine, the water is discharged into the atmosphere through a horizontal 50 ft section of the same pipe. The turbine power output is 10hp when the water in the discharged pipe is flowing at 5 ft/s. a. What is the turbine efficiency defined as the actual power output of the turbine divided by the power output that would be withdrawn if there are no friction within the turbine? b. If the turbine were by passed, what would be the flow rate of water through the 500 ft of 4in pipe?
QUESTION 4 The figure below shows a fluid flow system that is designed to pump water at 20 °C from a lower vented reservoir to an elevated vented tank. Note that the drawing is not to scale as the dimensions of the reservoirs are very large relative to those of the piping system. The suction line entering the pump is specified as 20 m of 3½" schedule 40 commercial steel pipe; the discharge line from the pump is 180 m of 2%" schedule 40 commercial steel pipe. 15 m 3 m 31/2-in Schedule 40 steel pipe Fully open gate valve 21/2-in Schedule 40 steel pipe Flanged regular 90⁰ elbows Pump Flow Swing-type check valve valve Butterfly (K butterfly = 0.8) a. Starting from the Bernoulli equation (in 'head' form) for the situation where the liquid levels in the two reservoirs are reference points 1 and 2, derive the correct equation for pump head Hpump (m) in terms of volumetric flow rate Q (m³/s) and other process variables (e.g. z, f, L, D, K). b. Using Excel (or another suitable program), create…
A horizontal 150 mm diameter pipe gradually reduces its section to 50 mm diameter, subsequently enlarging into 150 mm section. The pressure in the 150-mm pipe at a point just before entering the reducing section is 140 kPa and in the 50 mm section at the end of the reducer, the pressure is 70 kPa. If 600 mm of head is lost between the points where the pressures are known, compute the rate of flow of water through the pipe.
Basements that are prone to flooding are generally equipped with a sump pump, as illustrated in the image. (For purposes of illustration, the house above the basement has been removed, and dimensions have been distorted.) Water is diverted from the foundation, or wherever it seeps into the basement, to a small well in the floor. When needed, the submerged pump automatically switches on, pumping the water a height H above the pump through a pipe with diameter d. The pipe carries the water over the basement wall where it loses height hℎ and connects to a wider pipe, with diameter D, parallel to the ground. (Note the use of both lower-case and upper-case letters.) When the pump is operating, the flow rate is 0.929 L/s with an output pressure of 1.17×10^5 Pa. a. The water enters the pipe with an inside diameter d = 3.53 cm and rises to a maximum height H = 2.24m above the pump. What is the pressure, in pascals, at the maximum height? (Neglect frictional losses.) b. The pipe carries the…
8.61 cally through a 200-ft-long, 1.0-in.-diameter drawn tubing at a rate of 0.060 ft'/s if the pressures at the inlet and outlet are the same? What horsepower is added to water to pump it verti- Pump