Problem 5: Determine a) the weight of the water contained in the conical nozzle and b) the anchoring force required to hold in place the nozzle attached to the end of a lab sink faucet, when the water flowrate is 10 gal/min. The nozzle weight is 0.2 lb. The nozzle inlet and exit inside diameters are 0.6 and 0.2 in., respectively. The nozzle axis is vertical and the axial distance between sections (1) and (2) is 1.2 in. The pressure at section (1) is 68 psig and water exits as free jet from section-2. Neglect viscous effects. Given: pwter = 1.94 slugs/ft'; 1 gallon = 0.1336 ft’; Assume: Steady, incompressible flow; y axis vertically upward; uniform velocity distribution at (1) and (2);

Problem 5: Determine a) the weight of the water contained in the conical nozzle and b) the anchoring force required to hold in place the nozzle attached to the end of a lab sink faucet, when the water flowrate is 10 gal/min. The nozzle weight is 0.2 lb. The nozzle inlet and exit inside diameters are 0.6 and 0.2 in., respectively. The nozzle axis is vertical and the axial distance between sections (1) and (2) is 1.2 in. The pressure at section (1) is 68 psig and water exits as free jet from section-2. Neglect viscous effects. Given: pwter = 1.94 slugs/ft'; 1 gallon = 0.1336 ft’; Assume: Steady, incompressible flow; y axis vertically upward; uniform velocity distribution at (1) and (2);

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Exercise Problem No. 2: The water flow of 35,000 Liters/min was developed into a booster station with a pump installed rated as follows: Pressure at Discharge side= 4.18 bars, 850mm above the pump C.L. Suction Pressure= 220mmHg vacuum, 425mm below the pump C.L. Pipe Dia @ suction=16 inches and Pipe Dia @ Discharge 12 ½ inches. 1. Draw the illustrative diagram 2. Calculate the Head at discharge, Velocity Head, Elevation Head and the Total Head of the Pump.
A Huston turbine impeller with a diameter of 0.217 m is used in a tank with a diameter of 0.65 m filled with liquid to a height of 0.65 m. Four baffles (baffles) are used to avoid vortex, all with a width of 0.01 m. The turbine operates at 275 rpm with a liquid that has a density of 1000 kg/m³ and a viscosity of 0.020Pa.s. a) Considering that the mechanical efficiency is 50%, what is the power in HP of the commercial engine that you should specify?
A Huston turbine impeller with a diameter of 0.217 m is used in a tank with a diameter of 0.65 m filled with liquid to a height of 0.65 m. Four baffles (baffles) are used to avoid vortex, all with a width of 0.01 m. The turbine operates at 275 rpm with a liquid that has a density of 1000 kg/m³ and a viscosity of 0.020Pa.s. a) Calculate the power required in KWatts by the agitation system.
QUESTION 4 The figure below shows a fluid flow system that is designed to pump water at 20 °C from a lower vented reservoir to an elevated vented tank. Note that the drawing is not to scale as the dimensions of the reservoirs are very large relative to those of the piping system. The suction line entering the pump is specified as 20 m of 3½" schedule 40 commercial steel pipe; the discharge line from the pump is 180 m of 2%" schedule 40 commercial steel pipe. 15 m 3 m 31/2-in Schedule 40 steel pipe Fully open gate valve 21/2-in Schedule 40 steel pipe Flanged regular 90⁰ elbows Pump Flow Swing-type check valve valve Butterfly (K butterfly = 0.8) a. Starting from the Bernoulli equation (in 'head' form) for the situation where the liquid levels in the two reservoirs are reference points 1 and 2, derive the correct equation for pump head Hpump (m) in terms of volumetric flow rate Q (m³/s) and other process variables (e.g. z, f, L, D, K). b. Using Excel (or another suitable program), create…
2. A centrifugal pump installation has been designed to discharge 0.126 ?3/? of brine (sp.gr. = 1.2). The suction pipe is 305 mm and is at the same level as the discharge pipe which is 203 mm in diameter. At the centerline of suction flange, the vacuum is 154.2 mm Hg. The discharge pressure gauge reads 0.1379 MPa and is connected 1.22 m above the discharge flange centerline. The pump is driven by a 35 KW electric motor that will not carry overload and has an efficiency of 82%. There is no significant head loss. The design conditions have changed, and is now desired to increase the capacity of the pump by increasing the speed. The motor is so designed that its speed maybe increased but its power cannot exceed its design rating. Assuming the pump efficiency to remain constant, how much can the pump capacity be increased without overloading the motor?
Seven hundred gpm of water are being discharged by a centrifugal pump 5 ft. above the pump inlet. The inlet pressure is 4-in Hg above atmospheric and the discharge pressure is 29 psia. Assume the pump input is 8 hp, if the pump has an 8-inch diameter inlet and a 4-inch diameter discharge: 1.How much pressure loss in the pump? a. 28.4 ft-lbf/lb b. 5 ft-lbf/lb c. 4.7 ft-lbf/lb d. 38.1 ft-lbf/lb 2. How much is the velocity loss in the pump? a. 28.4 ft-lbf/lb b. 45.3 ft-lbf/lb c. 4.7 ft-lbf/lb d. 38.1 ft-lbf/lb 3. If the pump speed is increased from 1600 to 2400 rpm, what will be the new net flow rate in the pump? a. 800 gpm b. 1050 gpm c. 1400 gpm d. 1965 gpm 4. Find the new brake horse power if the pump speed in increased from 1600 to 2400 rpm. a. 64 hp b. 20.25 hp c. 8 hp d. 30.375 hp
Water at 5°C is to be pumped from the river to the bottom of a water tower. The pump is 5 m above the river (dimension "a" on the diagram below) and is supplied by a 6.00 inch schedule 40 pipe. The tank is 19.5 m above the pump (dimension "b" on the diagram below) and is supplied by a 4 inch schedule 40 pipe. The water level in the tank is 4.3 m above the inlet (dimension "c" on the diagram below). The pump delivers 0.021 m/s. Losses are estimated to be 1.2 m between the river and the pump, and 4.2 m between the pump and the tank. Discharge line Suction line Pump River a) Calculate the losses in the suction line in kPa, based on the given head loss in m. kPa b) Calculate velocity in the suction line in m/s. m/s c) What is the pressure at the inlet to the pump in kPa? kPa
2. A perfect venturi with the throat diameter of 1.8 inches is placed horizontally in a pipe with a 5 in inside diameter. Eighty 80 lb of water flow through the pipe each second. What is the difference between the pipe and venturi throat static pressure in psi?
Q No. 5: The diameter of side of a pump is 6 inches and that of the intake pipe is 8 inches. The pressure gauge at discharge reads 30 psi and vacuumed gauge at intake reads 10 inches of Hg. If Q=3cfs of water and the brake horsepower is 35. Find the efficiency of the pump. There are no losses. Note : Please Solve as Per Question's Statement. Need a Neat and Clear Solution.See Attached Picture For Detail .
The total head of fan is 200 m and has a static pressure of 210 mm of water gage. What is the velocity of air flowing if density is 1.16 m3/s.
The total head of fan is 200m and has a static pressure of 201mm of water gage. What is the velocity of air flowing if density is 1.16kg/m3.
For Questions 3 to 5, consider the following conditions: a centrifugal pump has diameters d1 = 7 in, d2 = 13 in, blade widths b1 = 4 in, b2 = 3 in, blade angles B1 = 25° and B2 = 40°, and rotates at 1160 r/min. If the fluid is gasoline at 20°C (p = 1.319 slugs/ft^3) and the flow enters the blades radially, estimate the theoretical or "design" quantities.