In an R-L-C series circuit a maximum current of 0.5 A is obtained by varying the value of inductance L. The supply voltage is fixed at 230 V, 50 Hz. When maximum current flows through the circuit, the voltage measured across the capacitor is 350 V. What are the values of the circuit parameters?

In an R-L-C series circuit a maximum current of 0.5 A is obtained by varying the value of inductance L. The supply voltage is fixed at 230 V, 50 Hz. When maximum current flows through the circuit, the voltage measured across the capacitor is 350 V. What are the values of the circuit parameters?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 7RQ: An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a...

See similar textbooks

Related questions

Q: Evaluate the gain coefficient for a laser amplifier that is 0.5 m long. The amplifying medium genera...

A: "Since you have asked multiple question, we will solve the first question for you. If you want any s...

Q: 1. Sketch the following CT functions: (a) g(t) = 2u(4-t) (d) x(t) = 68(31 +9) (e) y(t) = 5 sine(t /2...

A: We are authorized to answer one question at a time, since you have not mentioned which question you ...

Q: 2. For the following signal a (t) = e" u (-t) nlanlace transform integral to find the s-domain repre...

A: Note: As per the guide lines of the bartleby we are supposed to solve one question, when they are ...

Q: 10.31 a) Find the average power dissipated in the line in Fig. PI0.31. b) Find the capacitive reacta...

Q: An electrical device has a resistance of 30 Q and is supplied with a 5-ampere constant current sourc...

Q: 2) A0-250 mA range ammeter has an accuracy of 2% of full-scale reading. The ammeter measures 150 mA....

Q: a. What is the mechanism for the occurrence of Self Potential (SP)? b. What are the applications of ...

A: Self Potential (SP) is a geophysical formulation based on the proportion of automatic or natural ene...

Q: A coil of wire having a value of (6 + j9) ohms is connected in series with a capacitive reactance Xc...

Q: The PT of a 220kV transmission line has a ratio of 100kV: 300V. A voltmeter connected line to ground...

Q: 1) The required sampling frequency to get ten samples/cycle for a signal that has a baseband of 15 k...

A: Note: We are authorized to answer the first question since the exact one wasn’t specified. Please su...

Q: need the correct solves asap plz

A: In this answer we will find the answer to each of the questions above using the formula and concepts...

Q: 4) After the switch has been closed for a very long time, it is then opened. What is I3(topen), the ...

Q: Reduce the block diagram shown in the Figure below, and find the transfer junction C(s)/R(s). G4 R(s...

Q: Use picture below fo

Q: (a) Find the charge delivered to the device between t = 0 and t = 2 s. (b) Calculate the power absor...

Q: Three resistors are connected in series across a 12-V battery. The first resistor has a value of 10,...

A: Given that R1=1ΩV2=4VP3=12W

Q: :Find the values of VA, VB, Vo in the circuit, also determine I, I1, I2, load voltage, and load powe...

Q: Ży = 69 + 36j ohms Zw = 9 + 6j ohms Line to line Voltage = 420V Assume positive sequence and Van wit...

A: The solution is given below

Q: in a series circuit the voltage in every element is equal and follow the law of conservation of ener...

Q: Part B): Use mixed logic to design an implementation for FABiL using only NAND and NOT gates. Comple...

A: The NAND and NOT based design can be implemented by converting the basic gates into NAND gate.

Q: The impedance seen from the relay side in a distance relay is 10 ohms. Given that the CT ratio is 10...

A: Given: CT ratio is 1000 : 1 PT ratio is 100,000 : 110 Line has a resistance of 1 milliohm per km and...

Q: The conductors of a 66 kV, 50 Hz three phase transmission line are suspended horizontally as shown b...

Q: For the given circuit diagram a) Calculate I, I4, I6 ve I10 currents. b) Calculate the voltage drops...

A: Given circuit:

Q: Evaluation Question comparing the original equation with the minimization: Q1: Manually evaluate the...

A: The truth table can be obtained by using the given boolean expression and the same may be used to ob...

Q: Find the voltages using nodal analysis

A: Given circuit :

Q: Find the velocity of charge leading to 1 A current which flows in a copper conductor of cross-sectio...

Q: electric field

A: Electric field- The force at a unit charge particle which is positively charged at a particular poin...

Q: Zy = 69 + 36j ohms Zw = 9 + 6j ohms %3D Line to line Voltage = 420V Assume positive sequence and Van...

Q: Using Mason's Formula, Find the T.F. Y(s)/X(s) A В

A: In this question, We need yo determine the transfer function of the block diagram using the Mason g...

Q: Question : Get a state space model for the following electrical system. Make sure to clearly define ...

A: GIVEN: R1=5R2=3C1=10C2=7L1=4L2=1 FIND: space modal for electrical system

Q: Q3: A full-wave bridge rectifier with a 100V ms sinusoidal input has a load resistor of 1 k. a. If s...

A: Solve for the peak value of the input voltage. Vm=2Vrms=2100 V=141.42 V

Q: Vab = 220 angle 20 deg. Z-delta = 20 + 10j ohms Assuming positive sequence Van A LAB Von B Isc CA Ve...

A: The solution is given below

Q: 3 phase system V = 240kv supply to 2 sets of balanced loads connected in Y type Load 1: P=30kw,PF=0....

Q: Solve for the Laplace transform of sint sin 2t cost OF s(s?+16) 4(s +16) 4s 4(s?+16) 2s(s2+16)

Q: If you make a circuit with R1 6 KOhm and R2 = 9 KOhm, and your %3D %3D UIN UOUT GND

A: Solution

Q: Explain what is meant by forward and inversion modeling in the 2D/3D DC-resistivity geoelectric meth...

A: In 3-D direct current resistivity (DCR) modelling, we used an unique multi-resolution grid technique...

Q: Provide the transfer function of the system

Q: Q2: Find the values of VA, VB, Vo in the circuit, also determine 1, I1, Iz, load voltage, and load p...

A: We need to find out current and voltage for given circuit

Q: Use Mixed Logic to design a circuit to implement the expression given by the instructor using only t...

Q: A circuit has 3 resistors connected in parallel each having 15 ohms of resistance. What is the condu...

A: Conductance =1/resistance. If there are n resistors of equal resistors R are in parallel then their ...

Q: Two resistors, R1 = 100 Q and R2 = 200 N are connected in parallel. If the current through R1 is 1 A...

Q: R= 0.15 * 40 = 62 tor Yo km -3. XL=(27FL)* Yo = 2 (3,14) Cho) (l;3263x16) C40) XL 2on for 40 km 2: R...

A: In the given question the receiving end power is calculated by the formula: P=Scosθ Once we get its ...

Q: R1 C2 Vị Vo R2 a) For the second-order filter shown above, calculate the transfer function symbolica...

A: Given filter circuit is a second-order filter as there are two energy storing elements and the op-am...

Q: (-2 t² , f (t) = -π<t<0 2t2, 0 <t<n find the Fourier series of the following function in the form : ...

Q: amplitude spectrum for positive frequencies in the vicinity of the major lobe, and label important f...

A: The amplitude spectrum describes the signal components' amplitude as a function of component frequen...

Q: A 15 V source is connected across a 12-0 resistor. How much energy is used in three sec?

Q: The following information is given in connection with three loads connected to a 240-V source: load ...

Q: Determine the critical frequencies associated with low frequency response in the circuit given below...

Q: A 6A current source drives a load consisting a parallel combination of R1 = 60 N and R2 = 10N. Deter...

A: The correct answer is Option E. Explanation provided below. Please go through it.

Q: Two point charges (point 1 = +30 uC) and (point 2 = +40 uC) are located on the x axis in free space,...

A: Given,

Concept explainers

Capacitor

The capacitor is an element used to store electrical energy in the electrical field. A capacitor is a form of passive energy.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
An inductance coil consumes 500W of power at 10A and 110V and 60HZ. Determine the resistance and the inductance of the coil
A resistor & a capacitor are connected in series across 230V, ac supply. The current taken by the circuit is 4 A for 50 Hz frequency. The current is reduced to 2 A, when the frequency of supply is decreased to 40 Hz. Determine the value of resistor & the capacitor.
1. Enumerate five formulas for series-parallel capacitances across Vt source and draw the circuit. 2. Enumerate five formulas for parallel-series capacitances across Vt source and draw the circuit.
A capacitor in series with a 20-KO resistance across a 10 V ac source. What size C is needed for equal voltage across R and Xc at frequency of 100 Hz and 100 KHz.
A series R–L–C circuit comprises a 5µF capacitor, a 4ohm resistor and a variable inductance L. The supply voltage is 10∠0◦ V at a frequency of 159.1 Hz. The inductance is adjusted until the p.d. across the 4 ohm resistanceis a maximum. Determine for this condition (a) the value of inductance, (b) the p.d. across each component and (c) the Q-factor of the circuit.
Describe the behavior of the voltage across the resistor with time as thecapacitor charges. Explain the reason for this behavior.
What is the equivalent resistance ?? and what is the total inductance ??