If r0 = 0x20000000 and r1 = 0xC3B2A, after STR r1, [r0], #4 instruction is executed, which of the following is the data in memory address 0x20000002 (data layout big endian)?
Q: Assume the following initial values of registers r1-r5: re= 0x0 r1= 0x0 r2= 0x0000000A r3=…
A: Please check the step 2 for solution
Q: The hexadecimal data 36AB4CFD4CA2 is located in the real mode memory within Little Endian format…
A: Option b correct.
Q: Q1) If BX=1000, DS=0200, SS=0100, CS=0300 and AL=EDH, for the following instruction: MOV [BX] +…
A: Given Values are:- BX= 1000, DS= 0200, SS=0100, CS=0300, AL=EDH The instruction is MOV [BX]+1234H,…
Q: For this assignment, you are to write a MIPS assembly language program using the MARS IDE and assume…
A: Answer :
Q: If the first instruction "LXI H, 1100H" is positioned at address 7000H in memory, at what address…
A:
Q: Q2/ The following program have been executed by an 8085 Microprocessor. Write down the sequence of…
A: Let see the solution below.
Q: CPU Datapath The following figure shows the overall datapath of the simple 5-stage CPU we have…
A: ANSWER: a) MUX 1 Input 1: Register A input 2:Register B b) MUX 2 Input 1: Register C input…
Q: Assume that two numbers: dividend and divisor are saved in memory address M1 and M2 respectively.…
A: Given that Assume that two numbers: dividend and divisor are saved in memory address M1 and M2…
Q: Let R15=0x0000 00FF. The contents of the memory location at an address equal to the last 5 digits of…
A: R15 =0x0000 00FF. The contents of the memory location at an adress equal to the last digits of your…
Q: Location 600 contains 601, 601 contains 607 and 607 contains 613. What are the contents of register…
A: The correct answer is D. 613
Q: Assume the following contents of registers and quadwords in memory: Location Value %rax Ox8 %rbx Ox1…
A: leaq s,d Here, “s” denotes source, “d” denotes destination. This instruction loads the address of…
Q: Q1) Write a program to add 3 numbers ( 2 bytes each), The 1" one is stored in memory locations…
A: Note: As per our guidelines we can able solve only three question. So, please repost the remaining…
Q: 3. Assume the following 64b register contents: x5 O×0000000OODEADFAD, x6 = 0×BADBEEF011223344 For…
A: Answer is given below .
Q: Question Write an assembly code to implement the y = (x1+x2) * (x3+x4) expression on 2-address…
A: The assembly code for 2-address machine is given by Load R1,x1 // loads x1 to R1 Load R2,x2…
Q: Q3. Suppose $10 stores the base address of word array A and $1 is associated with h, convert to the…
A: Here, I have to provide a solution to the above question.
Q: 1) Write simple instructions (simple program) that will add two consecutive bytes of data storied…
A: Ans 1) CMP and SUB, both the instructions subtract one from the other. But the difference is, CMP…
Q: Assume the following values are stored at the indicated memory addresses and registers: Address…
A: Firstly movl moves a long (32-bits) from source to destination. Here we are given :
Q: At the start "STKPTR = 0x40" and then the following assembly code is executed. Address Instruction…
A: Given that STKPTR is 0x40 in decimal is 64 then executed the code line by line push means add pc…
Q: Loop: sll $t1, $s3, 2 0x[a] add $t1, $t1, $s6 0x[b] lw $t0, 0($t1) 0x[c] bne $t0, $s5, Exit 0x[d]…
A: The answer is an given below :
Q: Q. All instructions of Register Direct Addressing Mode generated by the above template are bytes…
A: Q 1: D) Either 3 or 4 Q 2: E) Cannot be calculated from the above template Q 3: D) MOV DL,…
Q: 8.3 An Acc-ISA CPU executes the following instructions using 3-bit op-codes and 5-bit address or 2's…
A: Here is the answer:-
Q: ' please solution with explain MICROPROCESSOR FUNDAMENTALS HW 3 Q1. Execute the following program…
A: Here we take : 1.FA + F4:…
Q: 10- Execute each instruction below and show the result of the registers. MOV AX, 453ЕН MOV BX, 1234H…
A: According to the information given:- We have to find the register values of after execution.
Q: Q:Find the value of SP address if SP= (2000) hex after execute the following instructions SP= PUSH A…
A: Stack Pointer: The stack pointer in the 8085 microprocessor is a 16-bit register that stores the…
Q: PLACE .FILL X45A7 LDI R3, PLACE The assembler puts the translated version of the LDI instruction…
A: Consider the instructions,PLACE .FILL x45A7LDI R3, PLACE• Here, the LDI instruction follows into the…
Q: If R0 = 0x8000 and memory data layout is as below, what are the r1 and r0 register values,…
A: LDR r1, [ro], #4 Here LDR stands for load data from memory into register. [Ro] means the content of…
Q: Assume the following register contents: $t0 = 0x01234567, $t1 = 0x56781234. Set back to these values…
A: The value of $t1, $t2, $t3, $t4 after the above instructions are given below
Q: 12. The ret instruction modifies the A. base register B. bp register C. flags register D.…
A: We know that there is nothing you can directly inject into the instruction pointer that will cause a…
Q: the available space list of a computer memory is specified as follows: 9 start address block address…
A: Collection of information and data is called memory. The operating system contains some of the…
Q: 1. The hypothetical machine of figure 3.4 also has two I/O instructions: 0011= Load AC fro I/O 0111=…
A: Given:
Q: Which statement is correct for the memory segments in 8086 microprocessor? a. For Stack segment,…
A: The memory segments in the 8086 microprocessor will have the stack point register which will have…
Q: 1- Write an assembly language program to search for data 44 in 9 memory locations start at (8000) if…
A: First Step: An assembly language program to search for data 44 in 9 memory locations start at…
Q: : . Find the time delay in the following program if the crystal frequency is 1 MHz. Do not ignore…
A:
Q: NAME: Registers A = 07H B = 16H D = ACH H = 34H C = FFH E = EDH L = 55H Quiz #5 Memory Map Write…
A: We need to write an assembly program using 8085 for the given scenario. * Since particular memory…
Q: If DS=7F0OH, BX=37EH and AX=1F05H, find the value of (AL) after executing (XLAT) instruction, if you…
A: 1)Used to translate a byte in AL using a table in the memory.XLAT changes the AL register from the…
Q: Part A For each byte sequence listed, determine the Y86 instruction sequence it encodes. If there is…
A: According to the information given:- We have to choose the correct option to satisfy the…
Q: Write the following in LC3 code: Write a program that compares two values stored at memory…
A: LC3 ASSEMBLY LANGUAGE It is a Case-sensitive Language with more…
Q: 3. Suppose M8=x and M9=y. After each instruction has been executed, what is the content of the…
A: Suppose M8-X And M9=Y. After Each Instruction Has Been Executed:
Q: If DS=7F0OH, BX=37EH and AX=1F05H, find the value of (AL) after executing *:(XLAT) instruction, if…
A: DS - Data segment register store the upper 16-bits of the address of two segments registers. BX-…
Q: 2. Use the following data definitions for the following questions: myBytes BYTE 10h, 20h, 30h, 40h…
A: Step 1:- Given:- myBytes BYTE 10h,20h,30h,40h myWords WORD 8Ah,3Bh,72h,44h,66h
Q: b) An 8051 subroutine is shown below: MOV RO, #20OH MOV @RO, #0 LOOP: INC RO CJNE RO, #80H,LOOP RET…
A: a) This subroutine is to clear the RAM locations 20H to 7FH b) total machine cycles: MC Bytes…
Q: If DI content equal 3000H then Instruction MOV AX, (DI) does the followings: Select one: Oa. Moving…
A: The DI instruction means “Disable Interrupts”. . It is a 1-Byte guidance. At the point when this…
Q: Write at most two instructions to move ONLY the fourth byte value in the register ($s1) into the…
A: This is how you can do this easily. Note: We are given the data in bytes so de defined the variable…
Q: below. a. Assume the accumulated count of counters C5:0 and C5:1 to be 148 and 36, respectively.…
A: Consider the program shown in Figure 11-36 in the text book in which the two counters accumulated…
Q: 6. What is the address of executing the following instruction: MOV CX, [FEH] if you know that DS=…
A: The instruction given :- MOV CX, [FEH] And DS = DC00H
Q: 1. Which type of JMP instruction (short, near, or far) assembles for the following: a. distance is…
A: Since you are asking multiple questions, we are doing first question for you. If you want solution…
Q: The first two bytes of a 4M x 16 main memory have the following Hex values: Byte 0 is FE Byte 1 is…
A: Hey, since there are multiple questions posted, we will answer first question. If you want any…
Q: Segment registers are:Select one: a. Define the logical address b. All the given options here C c.…
A: 1. Segment registers are: option b) is correct As segment registers define the logical address.…
Q: Øx20000012 Øxcd Ox20000011 Øxa3 Øx20000010 Øxfd OX2000000F Ox12 According to the memory view given…
A: Dear Student, Here register r3= memory content of r0 to r0 + 4 written in opposite order, as in…
If r0 = 0x20000000 and r1 = 0xC3B2A, after STR r1, [r0], #4 instruction is executed, which of the following is the data in memory address 0x20000002 (data layout big endian)?
Step by step
Solved in 2 steps
- Memory 12200 12201 12202 12203 12204 Content %D AA EE FF 22 What result is produced in the destination operand by execution the following instruction? a- LEA SI[DI+Bx+5] b- LDS SI.[200]Calculate the number of memory cycles required for the instructions "LDRH" in the below mentioned code snippet. Also write the data in the register R2 after the execution of each of the “LDRH" instructions. LDR R1,=0x8000000C LDR R3,-0XF31E4598 LDR R4,=0X1A2B3D4F STR R3, [R1] STR R4, [R1, #4] LDRH R2, [R1] LDRH R2, [R1, #1]! LDRH R2, [R1, #2]! LDRH R2, [R1, #3]Q1- Write a program in assembly language for the 8085 microprocessor to send 10 bytes of data located at the memory address (3000H to 3009H) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When sending each of the required bytes, you must adhere to the following: The two high bits of the start bits must be sent, after that the data bits are sent, after that the low bit of the stop bit is sent. The following flowchart will help you, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes. The solution must be integrated and include the calculation of the baudrate delay time Transmit No Set up Character Bit Counter Send Start Bit Wait Bit Time Get Character in Accumulator Output Bit Using Do Wait Bit Time Rotate Next Bit in Do Decrement Bit Counter Is It Last Bit? Yes Add Parity if Necessary • Send Two Stop Bits Return (a)
- Q1- Write a program in assembly language for the 8085 microprocessor to send one byte of data located at the memory address (3000H ) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz . When sending the required byte, you must adhere to the following: The two high bits of the start bits(1 1) must be sent, after that the data bits are sent, after that the low bit of the stop bit (0) is sent. The following flowchart will help you. The solution must be integrated and include the calculation of the baudrate delay timePlease in assembly to 8086 processor and registers is 16 bit please write an assembly code to fill the memory with the multiple of tens as following:o The first row of memory multiple of A (10 in decimal)oand the second row multiples of 14 (20 in decimal) and so on till 46(100 in decimal)********* . (Note that the length of each row is 16 byte)After executing the code display the content of the memory using:For each question usef range to fill the buffer by your name. for me my name needs 12letter so i use the range from 400 to 40C5. Load the register (CL) from the memory location [0500H] then subtract the content of this register from the accumulator (AL). Correct the result as a (BCD) numbers . Let [0500H] = 12H & AL = 3FH %3D
- Q1- Write a program in assembly language for the 8085 microprocessor to send one byte of data located at the memory address (3000H) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When sending the required byte, you must adhere to the following: The two high bits of the start bits must be sent, after that the data bits are sent, after that the low bit of the stop bit is sent. The following flowchart will help you. The solution must be integrated and include the calculation of the baud rate delay time Transmit Set up Character Bit Counter • Send Start Bit No Wait Bit Time Get Character in Accumulator Output Bit Using Do Wait Bit Time Rotate Next Bit in Do Decrement Bit Counter Is It Last Bit? Yes • Add Parity if Necessary Send Two Stop Bits Return (a)* Direction flag can reset to be zero by CLC True O False O ADD is a data transfer instruction which is used to add byte to byte/word to .word true O False O instruction is used to loon a set of instructions till zero flag becomesGiven a memory load instruction, "mov R0; [R1+1000]," please give the input that should be selectedat each multiplexer. You can write "none" for the multiplexers that are not used for this instruction.(a) MUX1:(b) MUX2:(c) MUX3:(d) MUX4:
- Microprocessor assembly code: There are 25 1-band numbers stored in memory starting from 1000H address. Write the program that shows the numbers greater than 50 with LEDs connected to port 2 with 2s intervals Tips: If the numbers are 01-03-55-21-51-34 ...... 66-FF 55-51 -..... 66-FF will be sent to Port 2 at 2s intervals. It should be assumed that the numbers were pre-entered into memory with the C 1000 command.Which of the following registers is used by the REP prefix to determine the number of times the string instruction is to be repeated? RAX RBX RCX RDX This flag determines whether the index registers are to be incremented or decremented. Parity flag Adjust flag Direction flag Sign flag6. What is the address of executing the following instruction: MOV CX, [FEH] if you know that DS= DC00H? OCL: DCOFEH, CH: DCOFFH OCL: DCFEH, CH: DCFFH CL: DCFFH, CH: DCFFH CL: DCOFFH, CH: DCOFFH