Determine the torque T that can be applied to the rectangular tube as shown in figure(5),if the average shear stress is not to exceed 12 ksi. The mean dimensions of the tube are shown and the tube has a thickness of 0.25 in.

Determine the torque T that can be applied to the rectangular tube as shown in figure(5),if the average shear stress is not to exceed 12 ksi. The mean dimensions of the tube are shown and the tube has a thickness of 0.25 in.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.3P: A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b...

See similar textbooks

Related questions

Q: The compound shaft shown in the figure consists of two steel [G = 80 GPa] pipe segments. The shaft…

A: Given Data: The modulus of rigidity of steel is, G=80 GPa=80 GPa×1000 MPaGPa=80000 MPa. The outside…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 216 mm and a…

Q: A cross section of the leading edge of an airplane wing is shown in the figure. The enclosed area is…

A: Given : A = 82 in2 T = 100 kip.in

Q: A motor driving a solid circular steel shaft transmits 40 kW of power at 500 rpm. If the diameter of…

Q: The Figure shows the motor A, which turns its connected pulley at 125 r.p.m. If the least safe…

A: Given data, turning of motor =125 rpm. diameter of shaft =30 mm =0.030m. shear stress =70…

Q: A solid circular shaft has a uniform diameter of 2" and is 10 ft long. At its midpoint, 65hp is…

Q: The thin walled cross-section, shown in figure, has an allowable shear stress of 2 ksi. Determine…

A: FOR THIN WALLED, τ×t=T2AA=MEAN AREA L=4-2×0.122=3.88inB=2.5-2×0.22=2.3inA=L×B= 3.88×2.3=8.924in2

Q: A tubular steel shaft transmits a power of P = 450 hp at a speed of 3000 rpm. Determine the maximum…

Q: A 250 hp motor turns a shaft at 2400 rpm. The shaft steps down in diameter 3.0-in to 2.5-in as shown…

A: Given:Power of motor, P=250 hpShaft speed, N=2400 rpmDmax=3.0 inDmin=2.5 in

Q: 2. A tube is made of aluminum (G = 24 GPa ) and has a rectangular cross section as shown in figure.…

Q: Circular solid ACB shaft is fixed supported between the wall at A and B. If the allowable shear…

A: Allowable shear stress τallowable=42 MPa=42×106 N/m2Let the maximum torque applied at section C be…

Q: 3.22 The compound shaft, composed of steel, aluminum, and bronze segments, carries the two torques…

Q: A hollow circular section shaft 2.5 m long is firmly supported at each end and has an inside…

Q: A solid shaft of 150 mm diameter is used to transmit torque. Find the maximum torque transmitted by…

A: Given, Diameter of shaft = d = 150 mm Maximum shear stress = τ = 45 N/mm2 Polar moment of…

Q: 11 A rectangular bar section of aluminium alloy has outside dimensions 100 mm x 50 mm, as shown in…

A: As illustrated in the image, a rectangular bar section of aluminium alloy has outer dimensions of…

Q: A flanged bolt coupling consist of six 10 mm diameter steel bolts on a bolt circle 300 mm. in…

Q: c) The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure…

A: Given Data: τ=80kPa (i) Shear stress is to be given by: Maximum torque that can be transmitted.

Q: A solid steel shaft A of 60 mm diameter rotates at 300 rev/min. Find the greatest power that can be…

Q: Lets consider a solid circuar shalt subjected to the torque loads as shown. Determine the minimum…

Q: A hollow steel shaft with an outside diameter of 80 mm and a wall thickness of 11 mm is subjected to…

Q: The dimensions of the cross section of an airplane fuselage are shown in figure 1. If the fuselage…

A: Given Data: The torque subjected to the fuselage is, T=8 MN·m=8 MN·m×1000 mmm=8×103 MN·mm. The…

Q: QUESTION The shaft consists of solid 160 mm diameter rod segment PQ and RS, and the tubular segment…

A: To find: The maximum allowable torque T can be applied to the shaft. Given: The inner diameter of…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm, a…

Q: Problem 3.15. A hollow aluminium tube of rectangular cross- section as shown in Fig. 3.27 is…

A: We know that a hollow aluminum tube with a rectangular cross section is subjected to a torque of…

Q: 2. A tube is made of aluminum ( G = 24 GPa ) and has a rectangular cross section as shown in figure.…

Q: Calculate the torque T: i. if the shear stress of the brass sleeve in section AB is limited to τb =…

A: Shear stress is defined as the intensity of force acting on the cross sectional area. Shear stress…

Q: Q.1: A shaft composed of segments AB, BC is fixed between the two walls at A and C and loaded as…

A: This is the case of statically indeterminate shafts... For this types of cases we would have no. of…

Q: Q.4) A composite shaft is subjected to two torques as shown below. Shaft ABC is a hollow…

Q: find the maximum shear stress induced in a solid circular shaft of diameter 150 mm when the shaft…

Q: A Compound Steel (G=80GPA) Shaft consists of a solid 90mm diameter (segment1) and a solid 70mm…

Q: Q4-A circular shaft consists of steel and aluminum segments is subjected to the torques shown in…

Q: If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross…

Q: 4) The thin walled cross-section, shown in figure, has an allowable shear stress of 2 ksi. Determine…

Q: Problem1: The entire composite shaft shown in the following figure is manufactured using steel with…

A: GivenG=80GPatorque =Tτa=75MPa

Q: 1. The 2.0 in diameter shaft shown in the figure below is supported by two bearings and is subjected…

A: Given data: The diameter of the shaft is, d=2 in. Draw the diagram of the beam.

Q: A solid circular shaft has a uniform diameter of 2" and is 10 ft long. At its midpoint, 65hp is…

Q: The solid 35-mm-diameter shaft is used to transmit the torques applied to the gears. The shaft is…

A: Given data: To determine the maximum torque, draw the torque diagram for the given system. Thus,…

Q: A composite shaft is made of slipping a bronze tube of 3-in. outer diameter and 2-in. inner diameter…

Q: . The shaft shown in the figure is made from a steel tube, which is bonded to a brass core. If a…

A: Let assume torque acting on steel is T1 and Torque acting on brass is T2 ,so T1+T2=227 , equation…

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

Q: The shaft consisting of steel and aluminum segments carries the torques T and 3T. Find the largest…

Q: roblem 2: The following solid shaft is loaded as shown in the figure. The 100 Nm/m distributed…

Q: 2. A tube is made of aluminum (G = 24 GPa ) and has a rectangular cross section as shown in figure.…

Q: Q2 / A solid steel [G= 80 GPa] shaft of variable diameter is subjected to the torques shown in…

A: (a) Draw the diagram for the problem.

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 12.25 in. and…

A: Given data: d1o=12.25 int1=0.365 ind2o=5.5 int2=0.28 inTB=69 kip-ftTC=12 kip-ft Need to determine…

Q: Maximum shear stress developed on the surface of a solid circular shaft under pure torsion is 240…

Q: The solid cast-iron shaft shown in Fig.a is subjected to a torque of T = 400 lb # ft. Determine its…

A: Maximum shear stress,τmax=TrJwhere,r=radius of shaftT=torque=400 lb.ftJ=Polar…

Question

I need answer within 5 minutes please please with my best wishes

Determine the torque T that can be applied to the rectangular tube as
shown in figure(5),if the average shear stress is not to exceed 12 ksi. The mean
dimensions of the tube are shown and the tube has a thickness of 0.25 in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

, Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14 kN/m, and L = L2 m.
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A long, thin-walled tapered tube AB with a circular cross section (see figure) is subjected to a torque T. The tube has length L and constant wall thickness t. The diameter to the median lines of the cross sections at the ends A and B are dAand dB, respectively. Derive the following formula for the angle of twist of the tube: Hint: If the angle of taper is small, you may obtain approximate results by applying the formulas for a thin-walled prismatic tube to a differential element of the tapered tube and then integrating along the axis of the tube.
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
When drilling a hole in a table leg, a furniture maker uses a hand-operated drill (see figure) with a bit of diameter d = 4.0 mm. If the resisting torque supplied by the table leg is equal to 0.3 N · m, what is the maximum shear stress in the drill bit? If the allowable shear stress in the drill bit is 32 MPa, what is the maximum resisting torque before the drill binds up? If the shear modulus of elasticity of the steel is G = 75 GPa, what is the rate of twist of the drill bit (degrees per meter)?