c) The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure Q2(c). If the allowable shear stress of the shaft is 80kPa. (iii) Determine the maximum torque T that can be transmitted by the shaft. (iv) What would be the maximum torque T’ if a 25 mm diameter hole is bored through the shaft? Sketch the shear-stress distribution along a radial line in each case. (v) T

c) The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure Q2(c). If the allowable shear stress of the shaft is 80kPa. (iii) Determine the maximum torque T that can be transmitted by the shaft. (iv) What would be the maximum torque T’ if a 25 mm diameter hole is bored through the shaft? Sketch the shear-stress distribution along a radial line in each case. (v) T

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.12P

See similar textbooks

Similar questions

A shaft required to transmit 50kW of power will be running at 100rev/min. The maximum twist in 3m length of the shaft is limited to 1.5 degree. If the maximum torque is 30 percent more than mean or average torque. Assume entirely elastic action and take modulus of rigidity for the shaft material G = 135 GN/?2. Determine the following:a. Diameter of the shaft.b. Maximum shear stress developed in the shaft. I need answer ASAP. Thank you!
A solid 1.750-in.-diameter steel [G= 13,000 ksi] shaft is subjected to torques TB = 265 lb-ft and TD 90 lb-ft, acting in the directions shown. Assume a = 48 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 16 ksi, determine the maximum torque Tc that can be applied to the shaft. (1) Answer: Tc i B (2) b Tc (3) Tp lb-ft D
The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure Q2(c ). If the allowable shear stress of the shaft is 81kPa (i) Determine the maximum torque T that can be transmitted by the shaft. (ii) What would be the maximum torque T' if a 25 mm diameter hole is bored through the shaft? (iii) Sketch the shear-stress distribution along a radial line in each case. T T' Figure Q2(c)
A solid 14 mm diameter steel shaft is fixed to a wall at E. Torques are applied to gears A, C and D as shown. Determine the maximum shear stress in the shaft and the rotation angle for gear A. G = 80 GPa 40 N•m 280 N m 0.5 m 150 N-m B 0.3 m P. 100 mm 0.4 m (a)
Q2(c) The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure Q2(c). If the allowable shear stress of the shaft is 80kPa, i)Determine the maximum torque T that can be transmitted by the shaft. ii)What would be the maximum torque T' if a 25 mm diameter hole is bored through the shaft? Figure Q2(c.) |Q2 c) (i) T c The torsion formula :7 = J Т (0.019) T (0.019)^4 ; Therefore, the max torque T = x10 Nm 80 2 Q2 c) (ii) For point lying on the outside suurface of the shaft: x10 ="(0.019) * (0.019*-0.0125 ) ; Therefore the max torque T' Nm 80 2 Q2 c) (iii) The shear stress at point located at inner surface of shaft, T'c T = -= J ) (0.0125) = 7 (0.019*-0.01254) T'c kPa 4. 2 2.
What is the minimum diameter of a solid steel shaft that will not twist through more than 3.18 degrees in a 6 m length when subjected to a torque of 14KN-m. What maximum shearing stress is developed? Use G=83GN/m^2.
Q2/ A hollow shaft has to transmit 6MW at 150rev/min. The maximum allowable stress is not to exceed 60 MN/m? nor the angle of twist 0.3° per meter length of shafting. If the outside diameter of the shaft is 300 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN/m?
The rotation or twist in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 20 mm in diameter and shear modulus G of 80,000 MPa is:
Power transmitted by a hollow shaft at 300 rpm is 800 kW. The ratio of outer diameter to the inner diameter of the shaft is 1.5. The maximum torque transmitted exceeds the mean torque by 40%. What is the outer diameter of the shaft if the maximum permissible shear stress of the shaft material is 80 Mpa. (B) 213 mm (D) 426 mm (A) 142 mm (C) 95 mm
A shaft of uniform solid circular section is subjected to a torque of 1500 N m. Determine distribution of shear stress in the shaft and its resulting angle of torsion (i.e. deflection), When the shaft's diameter is 0.06 m, the shaft's length is 1.2 m, and the rigidity modulus, G = 77 x 10° N/m². a) When the shaft is replaced with a similar hollow (i.e. the same outer diameter) but the wall thickness 10 mm. b) Determine the material of a circular bar form experimental data of angle of twist obtained from a torsion test in a lab.
A solid constant-diameter circular shaft is subjected to the torques of TA = 480 lb-ft, TB = 1060 lb-ft, Tc= 860 lb-ft, and Tp = 280 lb-ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in %D Section 6.6. (b) If the allowable shear stress in the shaft is 5800 psi, what is the minimum acceptable diameter for the shaft? TB TA Tc (1) Tp (3) В C D Answer: (a) T1 = Ib-ft T2 = Ib-ft T3 = Ib-ft (b) d = in.
Micro Bh Micros Bb Micros - с * Question Completion Status: Question 2 2.0 d=1.50 in. dia. 1.9 1.8 Class r = 0.08 in. The figure below show a stepped shaft in torsion. Compute the maximum shear stress at the step when it rotates at 100 rad/s and transmits 5000 lb-in/s. Use CamScanner app or Notes app of iPhone to scan all hand-written pages into one PDF file. Attach the PDF file here to answer in this question. Class ( bbhosted.cuny.edu/webapps/assessment/take/take.jsp?course_assessment_id=_2374 Class D = 2.00 in. dia. r= Fillet radius Class G Cuent Projec suntur Et WA AS hp