QUESTION The shaft consists of solid 160 mm diameter rod segment PQ and RS, and the tubular segment QR which has an outer diameter of 200 mm and inner diameter of 160 mm in Figure 1. The tubular segment was applied an external torque 50 kN.m. If the material has an allowable 150 MPa. Determine the maximum allowable shear stress of Tallow torque T that can be applied to the shaft. T R Figure 1 50 kNm

QUESTION The shaft consists of solid 160 mm diameter rod segment PQ and RS, and the tubular segment QR which has an outer diameter of 200 mm and inner diameter of 160 mm in Figure 1. The tubular segment was applied an external torque 50 kN.m. If the material has an allowable 150 MPa. Determine the maximum allowable shear stress of Tallow torque T that can be applied to the shaft. T R Figure 1 50 kNm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A shaft is made of a steel alloy having an allowable shear stress of Tallow = 12ksi. IF the diameter of the shaft is 1.5 inches diameter the maximum torque T if a 1in, diameter hole is bored through the shaft? Sketch the shear stress distribution along a trial line in each case.
A1 m long and 35 mm diameter aluminum shaft is to be replaced by a steel hollow shaft of the same length and the same outside diameter. It is required to design the steel shaft to withstand double the shear stress that of aluminum shaft. Determine the inside diameter of the stee I shaft. Find the values of the shear stresses on each shaft if a torque of 3 kN.m is applied to both of d=20mm them.
The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the allowable stress in shear is 60 MPa, whatis the maximum permissible torque Tmax that may beexerted with the wrench?Through what angle f (in degrees) will the shafttwist under the action of the maximum torque?(Assume G = 78 GPa and disregard any bending ofthe shaft.)
Q-1 A. solid circular shaft of (100 )mm diameter is transmit (120 )KW at r.p.m . Find the shear stress in the shaft B. the lap joint shown is fastend by three (20 )mm diameter rivets . Assumming that P-50 KN .Determine a. the shear stress in each rivets b. the bearing stress in each plate c.the max average tensile stress in each plate 25mm IAAI 25mm 5¢ 130 Soler
Determne the snallest allowable diameter of the selded shuft ABCD, knowng that the allowable shear stress is "60mpa" and the radhvs of the dist 8* 50 mm is "r 80mm. ISO mn TGOONM
A solid brass shaft is loaded as shown below by two torques TB- segments are LAB = 700 mm and LBC 600 mm. A dBc = dAB mm LAB mm B Com dBC For brass, G = 41 GPa. Neglect the effect of any stress concentrations. LBC Determine the smallest diameters dAB and dBC for which an allowable shear stress of 50 MPa is not exceeded. Express each diameter as an integer in units of mm. dAB To 1100 Nm and Tc = 300 Nm. The lengths of the two Determine the magnitude of the total angle of twist in the shaft caused by the two applied torques for the diameters found previously Express your result in units of radians with five decimal places of accuracy. PAC = rad
Illustrate and completely solve the problem! Write legibly or type written the solutions. The shaft assembly is made from a steel tube 1 in. in diameter, which is bonded to a solid brass core 0.5 in. in diameter. If a torque of 250 lb-ft is applied at its end, determine the maximum shear stress in psi experienced by the assembly. Take G for steel at 11.4 x 103 ksi and G brass at 5.2 x 103 ksi.
Torsion. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which there are 12 bolts. The allowable shear stress is 55 MPa in the shafts and 23 MPa in the bolts. One shaft is hollow with outside diameter of 100 mm, while the other one is solid of diameter 50 mm. Determine the ratio of the outside and inside diameter of the hollow shaft and the bolt diameter so that both shafts and the flanged bolt coupling are having the same strength in torsion.
A sleeve made of AISI 1040 CD steel has inner and outer diameters 40mm and 50mm, respectively. It is press fit on a solid shaft of same material with diameter 42mm such that the nominal diameter between sleeve and shaft became 41mm. a. Find the pressure developed between shaft and sleeve. b. Draw the tangential, radial, and total stress as a function of radius, for both sleeve and shaft. c. Find the maximum shaft diameter that can be used before failure.
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
The same torque is applied to two tubes with identical metal sheets, determine the ratio of Tcircle/Tsquare of the shear stresses. Given: r = 15 mm, S = 22 mm, and t = 2.91mm.
A2000-in diameter solid shaft is subjected to an adal force of P- 560 Ib, a horizontal shear force of V-320 lh, and a concentrated torque of T- 900 Ib-in, acting in the directions shown. Assume that L-7.0 in Determine the normal and shear stresses at a) point H (b) point K For each point, show thesa stresses on a stress element. Answers (a) point H o, psi psi psi (b) point K o, - psi psi psi