A pipe (diameter = 50 cm) carries water at a rate of 1 m/s. A pump in the pipe, as shown in the below Figure, is used to move the water from an elevation of 10 m to 30 m. The pressure at Section 1 is 50 %D kPa gage and the pressure at Section 2 is 300 kPa gage. Assume h = 4 m. What power must be supplied to the flow by the pump? Report your final answer in Horsepower (HP). Z2 30 m p2= 300 kPa gage Z1 10 m pi= 50 kPa gage Pipe D=50 cm Head loss in pipe, ht=4 m Pump Water Q=1 m/s

A pipe (diameter = 50 cm) carries water at a rate of 1 m/s. A pump in the pipe, as shown in the below Figure, is used to move the water from an elevation of 10 m to 30 m. The pressure at Section 1 is 50 %D kPa gage and the pressure at Section 2 is 300 kPa gage. Assume h = 4 m. What power must be supplied to the flow by the pump? Report your final answer in Horsepower (HP). Z2 30 m p2= 300 kPa gage Z1 10 m pi= 50 kPa gage Pipe D=50 cm Head loss in pipe, ht=4 m Pump Water Q=1 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2- Water density =1000 kg/m and viscosity is 0.001 Ns/m², is pumped between two reservoirs at 0.2m/s through a 400 m of 8 cm diameter Cast Iron pipe and several minor losses as shown in the figure. Compute the pump power required in kW. Use the last one digit of your ID number for Z1 level in meter. Screwed Z2= 50 m regular 90° elbow Sharp exit Z;= ID m Sharp entrance Half-open gate valve `bend radius Pump Open globe valve 8 cm diameter
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. ( WITH FREE BODY DIAGRAM ) CHOIECES: A.2.56 B.-2.72 m C.12.74 m D.-4.67 m
Problem (3) Find the rate of change of h(t) (mm/s) if water is the fluid at all locations. Use V₁ = 7.1 m/s and Q = 1000 L/min. m₂ = 10 kg/s 4 cm dia. V₁ Answer: 120 cm h(t) 8
A water supplying pipe of diameter 14 cm, is used to pump the water to the house in the Tanuf hill at the height of 60 m above the ground. The flowrate at the end of the pipe is 180 lit/s. The pressure gauge is connected at the inlet of the pipe in the ground and measured as 35.5 N/cm2. Find the following: (i) The kinetic energy per unit weight at the entry of pipe (in m) (ii) Pressure head at the inlet (in m) (iii) Total available energy per unit weight of the water at the pipe entry (unit in m)
Water flows inside a solid cylindrical pipe, which narrows as it goes up to a height h (see diagram below). The lower horizontal section has circular cross-sectional diameter d, whereas the upper horizontal section has diameter d/2. Let us denote A to be a point at the lower horizontal section and B to be a point at the upper horizontal section. The flow speed at A and B is uд and u, respectively. The pressure at A and B is PA and PB, respectively. РА UA Oom Ja d d/21 1 UB h (a) Assuming water to be incompressible, show that the flow speed at B is four times the flow speed at A. (b) Use Bernoulli's equation to find the drop in the water pressure from A to B. Express the result in terms of h, uд, the density of water p, and the acceleration of gravity g. (c) Above certain critical height h, vapour bubbles start to appear at the top horizontal section, which hinders water flow through the pipe. Explain why this happens.
Water (p 1.96- slug) flows through the pipe system below. Data is given below: = ft³ Pipe 1: V₁=1.8 ft, D₁ =2.4 inches, p₁ =24.9 psi Pipe 2: V₂=1.4 t, D₂=1.9 inches 2 Pipe 3: D3=0.7 inches Assume no energy is lost to friction. Find the pressure p3. Report your answer in psi. V₂ V₁ P₁ D₁ D₂ P2 D3₁ V3 P3
In the figure shown below the water comes out of a tank and runs through pipe 1 (D1=10cm) that splits into two smaller pipes open to atmosphere (D2=3cm D3=6.5cm). The pressure shown in the tank manometer is 10kPa. Deermine the flow velocity in pipe 1 considering a perfect fluid.
A room has a volume of 349 m3. An air-conditioning system is to replace the air in this room every 81.5 minutes, using ducts that have a square cross section. Assuming that air can be treated as an incompressible fluid, find the length of a side of the square if the air speed within the ducts is (a) 2.00 m/s and (b) 7.00 m/s. a: b:
The water is flowing through a pipe having diameters 30 cm and 21 cm at sections land 2 respectively. The rate of flow through pipe is 40 litres/s. The section 1 is 7 m above datum and section 2 is 3 m above datum. If the pressure at section 1 is 37 N/cm? , find the following by neglecting losses: (ENTER ONLY THE VALUES BY REFERRING THE UNIT GIVEN IN BRACKETS) ) Area of cross section of section1 (unit in m?) = Area of cross section of section2 (unit in m?) = velocity at section 1 (unit in m/s) = velocity at section 2 (unit in m/s) = (ii) difference in datum head (Unit in m) = Pressure head at section 1 (Unit in m) = pressure head at section 2 (unit in m) =
Water in a vertical (i.e., gravitational force of the fluid in the nozzle plays a role, and the elevation change in the Bernoulli's Equation, if needed, should be considered) pipe is charging from an attached bend nozzle into the atmosphere as shown in Fig. 5. The nozzle's weight is 20 kg. The pipe and the nozzle are connected by a flange. The gage pressure of the flow at the flange is 35 kPa when the discharge rate is 0.1 m³/s. The volume of the bending nozzle is 0.012 m³. Calculate the vertical component of the anchoring forcing required to hold the nozzle in place and determine its direction. G= 9.81 m/s². The density of water is 1000 kg/m³. ChatGPT solution: Nozzle 1 Area -0.01 m² P-35 kPa Area -0.025 m² 0.10 ms Figure 5: Q5 35 degree
A pipe of diameter 18 cm, is used to pump the water to the house in the Hamra hill at the height of 50 m than the ground. The discharge at the end of the pipe is 220 lit/s. The pressure gauge is fitted at the entry of the pipe in the ground is 35 N/cm². Find the following: (i) The velocity head at the entry of pipe (in m) (ii) Pressure head at the inlet (in m) (iii) Total available energy per unit weight of the water at the pipe inlet (unit in m) (Enter only the values by referring to the units given in brackets & DO NOT write the unit & do not send the handwritten answers to my mail id....) velocity head at the entry of the pipe is = (unit in m) pressure head at inlet = (unit in m) Total available energy per unit weight of the water at inlet of the pipe (unit in m) ,
Water flows through a Venturi meter, as shown in the figure. The pressures of the water at locations a and b in the pipe support columns of water that differ in height by L = 12 in. The atmospheric pressure is 14.7 Ibf/in?, the specific volume of water is 0.01604 ft/lb, and the acceleration of gravity is g = 32.0 ft/s?. Patm = 14.7 Ibr/in.? g = 32.0 ft/s² Water v = 0.01604 ft/lb Determine the difference in pressure between points a and b, in Ibf/in2?. Does the pressure increase or decrease from point a to point b? Sten 1