A 0.2 m wide (out of plane) gate in a sea wall is hinged at A and bolted at B. Given the density of sea water is 1,025 kg/m3 and the depth of water hA = 4.2 m, determine the magnitude of the reactions at A and B that act normal to the gate. 1.0 m A B RA= (magnitude only; tolerance 5 N) RB = (magnitude only; tolerance 5 N) 数字单位单位 * * 0.6 m

A 0.2 m wide (out of plane) gate in a sea wall is hinged at A and bolted at B. Given the density of sea water is 1,025 kg/m3 and the depth of water hA = 4.2 m, determine the magnitude of the reactions at A and B that act normal to the gate. 1.0 m A B RA= (magnitude only; tolerance 5 N) RB = (magnitude only; tolerance 5 N) 数字单位单位 * * 0.6 m

Name: A 0.2 m wide (out of plane) gate in a sea wall is hinged at A and bol
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A 0.2 m wide (out of plane) gate in a sea wall is hinged at A and bolted at B. Given the density of sea water is 1,025 kg/m³ and the depth of water hA = 4.2 m,determine the magnitude of the reactions at A and B that act normal to the gate.1.0 mABRA=

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2.) Given the two-compartment vessel shown in the figure. Gage A reads 85 psig: gage B inside compartment X reads 25 psig. If the barometer (outside compartments X & Y) reads 30.61 in Hg, determine the reading of gage C in psi. Ans: 60 psia B Y
Problem 1. The gauge pressure of the air in the tank shown in the figure below is meası red to be 65 kPa (fluids’ densities as follows: PH20 = 1000 Kg , Poil = 742 Kg/m³, Phg = 13650 Kg/m³). Determine the differential height а) h of the mercury column Oil 65 kPa Determine the resultant force per b) unit depth acting on the quarter of circumference (radius R=15 cm) at the left bottom corner of the tank. 75 cm Air Water |30 сm h - Mercury H%3D75 cm
Three liquids of different densities fill connected tubes as shown in the figure below (not drawn to scale). The specific weights of two of the liquids are related by y2 = 3y1. Find y3 in terms of y1. Y1, 40 mm Y2 = 3Y1 60 mm 30 mm Y3
80 min 200 mm 11. The figure shows a high-pressure hand pump used for boosting oil pressure in a hydraulic line. When the handle is in equilibrium at theta=15 deg under the action of a force P-120 N, determine the oil pressure p which acts on the 46 mm diameter piston. (Pressure on the top of the piston is atmospheric). 200 mm piston. Ans: P=0.27 MPa mm
A manometer is installed in a vertical pipeline. Determine the difference in pressure in PSI between point A and point B if the gauge liquid has a specific gravity of 1.50 and shows a deflection of 80cm. A SG= 1.50 Water 80cm
Q4//Determine the required vertical force F to be applied at the lower edge to open the square gate (2.8m*2.8m) as shown in figure below: Negative pressures 8250Pa 1.8m Gasoline s-0.7 hinge gate
A conical tank having a height of 5ft and base of 12 in radius contains 0.7ft3 of water. How much additional water is needed to fill the tank? Select the correct response: 0.554 in3 0.594 in3 0.184 in3 O 0.784 in3
3.6 m R 1m 1.2 m 2.5 m Oa 3m The banner has a density of 670 kg/m and is 6mm-thick. The pipe has the linear weight of 9N/m. Which of the following completes the force diagram? A. Foy, Foz, Moy, Moz B. Fox. Foy, F oz, Mox, Moy, Moz C. Fox, Foy, Foz, Moy, Moz D. Foy, Foz, Mox, Moy, Moz Р 1.25 m 1.5 m WOR 1.25m Wanner Fo WpQ 3.6 m Oo 2.5 m R 1 m
Ocean Marsh d = 9 ft 5.79 A freshwater marsh is drained to the ocean through an automatic tide gate that is 4 ft wide and 3 ft high. The gate is ħeld by hinges located along its top edge at A and bears on a sill at B. At a given time, the water levels in the marsh and in the ocean are h = 6 ft and d = 9 ft, respectively. Determine the force exerted by the sill on the gate at B and the hinge reaction at A. (Specific weight of salt water = 64 lb/ft³.) h =6 ft 3 ft B Fig. P5.79
. The gate shown is hinged through a point A and is restrained from opening by a fixed ridge at point B. For a gate width of 7 feet, 45° SG = 0.86 20" A Hinge 32" SG = 1.23 B
1- A 60 cm square gate has its top edge 12 m below the water surface. It is on a 45 angle and its bottom edge is hinged as shown Water in Fig. What force P is needed to just open the gate and its location? Hinge 45° 2- A tank containing water is shown in Fig. E Calculate the total resultant force acting on side ABCD of the container and the 6 ft location of the center of pressure. y = 62.4 Ib/ft3 Water -20 ft
The figure below represents the working principle of an industrial pressure gauge. The cylinders and tubing are filled with an oil whose density is 0.780 g/cm3. The sections transverse pistons have an area of 40 cm² and 4000 cm² (a) Calculate, in N, the value of the force F to be applied to the smaller piston of the press shown in the figure, required to balance the load F’ of 4400 kgf on the larger plunger. (1 kgf = 9,80665 N) (b) what must be the relationship between F and F’ for h = 0 m?