A 50 mm X 80 mm rectangular steel plate subjected to the uniaxial stress condition is shown in the figure below. The modulus of elasticity of the steel is 200 GPa and the Poisson's ratio is 0.30. Determine the new length of: I) Side AB 2) Side BC 3) Diagonal AC 80 mm A G=200 MPa G= 200 MPa C D ww os

A 50 mm X 80 mm rectangular steel plate subjected to the uniaxial stress condition is shown in the figure below. The modulus of elasticity of the steel is 200 GPa and the Poisson's ratio is 0.30. Determine the new length of: I) Side AB 2) Side BC 3) Diagonal AC 80 mm A G=200 MPa G= 200 MPa C D ww os

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. b C NANTSELEINE Steel: A = 900 mm² E = 200 GPa L=1.5m Bronze: A=1200 mm² E=83 GPa L=2.0m What is the ratio of the elongation of steel to bronze? O 0.367 O 0.433 O 0.467 0.333
Sketch the idealized stress-strain curve for A36 Steel. Label and provide the appropriate values for Fy, Fu, E and ey, and eu. Note: Use the “rule of thumb” that eu =200ey . Explain in detail what each value physically represents in the material.
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. a b C Steel: A-900 mm E = 200 GPa L=1.5m Bronze: A 1200 mm E=83 GPa L=2.0m What is the ratio of the elongation of steel to bronze? 0.367 0.433 0.467 0.333
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. b C P Steel: A=900 mm² E = 200 GPa L=1.5m Bronze: A 1200 mm E=83 GPa L=2.0m What is the value of P without exceeding the allowable stress of bronze, in kN? 174 145 161 124
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b I Steel: A 900 mm Bronze: A E 200 GPa E 83 GPa L-2.0m L=1.5m What is the value of P without exceeding the allowable stress of steel, in KN? 230 250 280 340 1200 mm
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b C P Steel: A-900 mm² Bronze: A=1200 mm² E = 83 GPa L=2.0 m E = 200 GPa L=1.5m What is the value of P without exceeding the allowable stress of bronze, in kN? O 161 O 174 O 145 124 4
2. The bronze bar 3 m long with a cross-sectional area of 350mm2 is placed between two rigid walls. At a temperature of -20 oC, there is a gap of 2.2 mm. Find the temperature atwhich the compressive stress in the bar will be 30 MPa ifthe bar will experience:a. No tensile.b. With an tensile of 5,000 N.Use α = 18.0 x 10-6 /oC and E = 80 GPa.
SITUATION. A steel plate ABCD of thickness t = 5mm is subjected to uniform stresses: = 100 MPa 0₂ = -60 MPa. Ox E =200GPa, v= 1/3 a = 160mm and b = 200 mm Calculate the change in thickness (mm). -0.0023 mm 0.0023 mm O O 0.0045 mm - 0.0045 mm Ł B AL C D X
q7 A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load of 30 kN. If Poisson's ratio is 0.25 and Young's modulus is 200 GPa, an increase in volume will be (b) 150 mm3 (d) 130 mm3 (a) 160 mm3 (c) 140 mm3
X Your answer is incorrect. Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.42 in.? and an elastic modulus of 2180 ksi. Bar (2) has a cross-sectional area of 1.139 in.? and an elastic modulus of 4150 ksi. Assume L;-23 in., L2-41 in., Q-6.7 kips, P-3.7 kips, and R-14.1 kips. Determine the horizontal deflection of end Crelative to end A. R (1) (2) P L1 L2 Answer: UCIA - i 0.0725 in.
One of the following values is a possible for possion ratio for steel ? a. Zero b. one c. 0.3 d 0.9
A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial load of P = 31,025 lb. produced a deformation of 0.115 inch over a gauge length of 2.10 inches and a decrease of 0.0080 inch in the 0.60-inch thickness of the bar. a. Determine the lateral strain. b. Determine the axial strain. c. Determine the Poisson’s ratio v. d. Determine the decrease in the 4.05-in. cross-sectional dimension (in inches).