9. If we have AX-8A3C H, CL-02 H. the result of performing SAL AX,CL is: a. C51E H c. 451E H b. E28F H d. 228F H 10. If you have a data of size byte stored in DL. I ask you to use the instruction ROL DL,0D H then the number of rotation will be: a. 5 times b. 10 times c.14 times d. Neither a,b nor c

Q: 5. When two words are multiplied (one in BX), the most significant word of result will be in…

A: 5)The multiplication result is taken by the registers DX and AX respectively.so the answer is d.…

Q: Q) 2. Answer the following: A. What happens if AL=20h and AH= 10h. When each of the following…

A: START:MOV AX,DSEG MOV DS,AX MOV CX, 04H MOV BX,0000H BACK: MOV AL,ST1[BX] CMP AL,ST2[BX] JNZ UNEQ…

Q: Q) 3. Answer the following: A. What is result of executing the following instruction sequence? MOV…

A: Answer : Result: 00C0H

Q: What is result of executing the following instruction sequence? MOV BX, 100H MOV [ BX], 0C0ABH MOV…

A: Answer:

Q: What is result of executing the following instruction sequence? MOV BX, 100H MOV [BX] , 0C0ABH MOV…

A: Answer:

Q: 4. We have the following data for a branching instruction, where T = branch is taken, and N = the…

A: Branch Prediction: Requires three things to be predicted at fetch stage- Whether the fetched…

Q: Q 2/A- Write a program to add the following five data bytes stored in data segment offset starting…

A:

Q: 1. Verify each instruction starts from these values: AL = 85H , BL = 35H a) MUL BL b) IMUL BL c) DIV…

A: This Question comes from the portion of Control and systems from microprocessor all the given…

Q: Two word-wide unsigned integers are stored at the physical memory address 00A0016 and 00A0216 ,…

A: Given: Two word-wide unsigned integers are stored at the physical memory address 00A0016and 00A0216…

Q: a. What will be the contents of AX, BX, CX and DX registers after the execution of the following…

A: I have explained below every step of the above query. I hope you can understand easily.

Q: Suppose that a C++ int variable x is associated with register $t1. Write the MIPS I instruct…

A: Actually, register is a used to store small amount of data.

Q: We wish to execute a single LC-3 instruction that will subtract the decimal number 33 from R1 and…

A: we need to write LC-3 instruction that will subtract the decimal number 33 from R1 and put the…

Q: Two word - wide unsigned integers are stored at the memory addresses OA00 H and 0A02 H respectively,…

A:

Q: Considering the following MIPS code: begin: addi $t0, $zero, 22 li $a0, 1 move $t1, $zero loop: $t0,…

A: Question (a) :- #Label beginbegin:   #Set register t0=22   addi $t0,$zero,22   #Set t1=0   move…

Q: Consider the following instruction format and the list of opcodese Opcode 4 bits (15 – 12) Addresse…

A: 1) Running the Program Line by Line for 1.  PC =    500       Content = 5800.      Here at 500 the…

Q: Implement the following high-level code segments. Assume the integer variables g ,h ,m ,and r are in…

A: Assume that “g”, “h”, “m”, and “r” are stored in registers “$s0”, “$s1”, “$s2”, and “$s3”…

Q: B- Write a single instruction that loads AX from address 0200 H and DS from address 0202H.

A:

Q: Question 4: What will be the final result in memory, the shown register, and the various flag bits…

A: MVI A,03 ---> This will load 03 to A register. So A=03 ADI 02--->This will perform A=A+02. SO…

Q: Execute the following instruction. What will be the new value of the lowest byte of memory content…

A: Problem Statement: Execute the following instruction. What will be the new value of the lowest byte…

Q: .ORIG X3000 ADD R7, R6, #-5 LEA R6, Y BRz B LDR RO, R2, #2 HALT A B .BLKW .FILL 2 .FILL 1 5 Y .FILL…

A: Given : Given the set of instructions with the starting address as X3000. The task is to find the…

Q: Implement the following high-level code segments .Assume the integer variables g ,h ,m ,and r are in…

A: Given that the integer variables g, h, m, and r are stored in registers $s0, $s1, $s2, and $s3…

Q: Implement the following high-level code segments .Assume the integer variables g ,h ,m ,and r are in…

A: Given that the integer variables g, h, m, and r are stored in registers $s0, $s1, $s2, and $s3…

Q: Implement the following high-level code segments .Assume the integer variables g ,h ,m ,and r are in…

A: Given: Given that the integer variables g, h, m, and r are stored in registers $s0, $s1, $s2, and…

Q: What will be the value of AX (in Hexadecimal) after execution of the following instructions: STC…

A: What will be the value of AX (in Hexadecimal) after execution of the following instructions: STC MOV…

Q: 7. Using the following list file, verify the forward and backward jumps address calculation. Line PC…

A: As for our rules we can answer only one question at a time please post remaining questions…

Q: 1. Neatly work out the following bitwise operations. Show the work step by step. Give the answers in…

A: Answer: Our instruction is answer the first three part from the first part and . I have given…

Q: What are contents of R5 after execution to each of the following instruction? (Assume R2 contains…

A: We have different Arithmetic and logical instructions here, we have  to find out the contents of R5.

Q: -Write a single instruction that will load AX from address [1F22 H] and DS from address [1F24 H].

A: TO load AX from address [1F22 H] using MOV instruction:- MOV AX, [1F22H]

Q: Assume that you are given the following MIPS code fragment: Label01: instruction1 instruction2…

A: suppose that the first instruction is located 10000, then the value of offset field of the…

Q: Write a short program that uses the XLAT instruction to convert the BCD numbers 0–9 into ASCII-coded…

A:

Q: Using emu8086 (a) RUN this code, (b) identify & Fix the error (c) Show output. (e)Explain the…

A: $nasm -f elf *.asm; ld -m elf_i386 -s -o demo *.omain.asm:1: error: parser: instruction expected…

Q: below. a. Assume the accumulated count of counters C5:0 and C5:1 to be 148 and 36, respectively.…

A: Consider the program shown in Figure 11-36 in the text book in which the two counters accumulated…

Q: Consider the following y86-64 program: .pos 0x0 irmovq $128,%rdx irmovq $3,%rcx rmmovq %rcx,…

A: It is defined as a type of program which has a lot more instructions. IA32 has a lot of quirks. Y86…

Q: What are the values stored in memory address [1200] and [1400] after execution, respectively ? MOV…

A: Solution: MOV AL,[1200] will load 25h value in AL register MOV AH,AL ​​​​​​​will load 25h value…

Q: (e) What is the effect of executing the following two 8051 instructions MOV C, PSW.0 MOV 13H, С

A: The effect of executing the following two 8051 instructions is: MOV C, PSW.0 MOV 13H, C

Q: Write a program in assembly language using the MIPS instruction set to calculate the nth Fibonacci…

A: The MISP instruction for the calculation of nth Fibonacci number would be as follows .text…

Q: What would be the final value of BX after the bitwise AND instruction executes? MOV BX, OFFFFH AND…

A: Please refer to the following step for the complete solution of the problem above.

Q: Write a MIPS program that executes the statement: s = (a + b) – (c + 101), where a, b, and c are…

A: please find the code in step 2. please comment if you need any help. Happy Learning!

Q: Write a MIPS program that executes the statement: s = (a + b) – (c + 101), where a, b, and c are…

A:

Q: 2. Study this program then answer the questions that follow: MOV DX, 1234 H MOV BX , 3099 H MOV AL,…

A: The registers AX,BX,CX,DX stores the 16 bit values. The AL and AH are the registers that store the…

Q: 2. Study this program then answer the questions that follow: MOV DX , 1234 H MOV BX, 3099 H MOV AL,…

A: 1)here , the given code is of addition operation. Where two numbers are being added using AX…

Q: After the bitwise AND instruction is executed in the code sequence below, the final value of BX…

A: BX=91BAh AND BX,91B2h Source 0010 1001 1101 0110 Destin 1000 0001 1000 0001 Result 1010 1000 0101…

Q: Question// if AX=7272h and CX= 127F, what the value of both flag PF and AC after execute the…

A: AC(Auxiliary Carry Flag) is set to 1 if there is a carry from B7 to B8 PF(Parity Flag) : If…

Q: please solution with explain Question 4: What will be the final result in memory, the shown…

A: Answer: I have given answered in the handwritten format in brief explanation.

Q: 4) Write an ALP for 8086 microprocessor to solve the following equation Y = (A x B) + C. A, B and C…

A: Answer is in DX register

Q: 4) Write an ALP for 8086 microprocessor to solve the following equation Y = (A x B) + C. A, B and C…

A: The 8086 code with comments is given in step 2.

Q: Using matalab H.W 2: Write a piece of assembly code that can program PPI 8255 as port A as I/P,Port…

A: the answer is given below :

Q: Using matalab H.W 2: Write a piece of assembly code that can program PPI 8255 as port A as I/P,Port…

A:

Q: Q2/ Two byte -sized BCD integers are stored at the symbolic offset addresses NO1 and NO2…

A: First number stored at NO1 address Second number stored at NO2 address Subtraction and to store the…

Q: 9. a) Write a simple assembly program to store values ex25 and ex86 into locations ex40000030 and…

A: Part A) LDR R0,=0x40000030   ; load memory location to R0 LDR  R1, =0x40000025   ; load memory…