Considering the following MIPS code: begin: addi $t0, $zero, 22 li $a0, 1 move $t1, $zero loop: $t0, $t1, finish $t1, $t1, $a0 addi $a0, $a0, 1 addi $t0, $t0, -3 loop beq add j finish: a. Explain the meaning of each instruction by inserting (inline) comments b. Give a possible high-level pseudo-code for the above MIPS code. c. What is the value of $t0 when the program reaches "finish"? d. What is the value of $a0 when the program reaches "finish"?

Considering the following MIPS code: begin: addi $t0, $zero, 22 li $a0, 1 move $t1, $zero loop: $t0, $t1, finish $t1, $t1, $a0 addi $a0, $a0, 1 addi $t0, $t0, -3 loop beq add j finish: a. Explain the meaning of each instruction by inserting (inline) comments b. Give a possible high-level pseudo-code for the above MIPS code. c. What is the value of $t0 when the program reaches "finish"? d. What is the value of $a0 when the program reaches "finish"?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

25: . Find the time delay in the following program if the crystal frequency is 1 MHz. Do not ignore the time delay due to the first and last instruction. DELAY: LDI R16, 30 AGAIN: LDI R17, 35 HERE: NOP NOP DEC R17 BRNE HERE DEC R16 BRNE AGAIN RET 26: Write a program to display 2 on 7 segment. A 7 segment is connected to PortD.
Read the following code carefully to answer what it does: START: MOV SI, 0300 MOV DI, 0302 ADD (DI), AX STOP: MOV AX, (SI) HLT Select one: O a. None of the above O b. CLC instruction should be added to the beginning of the program O c. Adding two words. Result in 0302H & 0303H O d. Adding two words. Result in 0301H & 0302H Oe. The content of destination word does not change
The instruction that is not possible among the following is a) MOV AX, BX b) MOV AX, [BX]. c) MOV 55H, BL d) MOV AL, 55H
-Two word wide unsigned integers are stored at the physical memory addresses 00A00 and 00A02, respectively. Write an instruction sequence that computes and stores their sum, difference, product, and quotient. Store these results at consecutive memory locations starting at physical address 00A10 in memory. To obtain the difference, subtract the integer at 00A02 from the integer at 00A00. For the division divide the integer at 00A00 by the integer at 00A02. Use the register indirect relative addressing mode to store the various results.
Computer Science Encode the following instruction from MSP430 assembly to MSP430 machine code. You will have to put Byte 0 in the first blank, byte 1 in the second, and so on. Note you do not need to write 0x, it is assumed the entered values are hex bytes. mov #17794, r14 Byte 0 Byte 1 Byte 2 Byte 3 0x 1. 0x 2. 0x 3. 0x 4.
Q2. In The following, the instructions are dependent on each other, if A B8 H. and Cy 1, next to each instruction write down the content of the Accumulator IN hex and the Carry after the instruction has been executed: %3D 1. RR A 2. RRC A 3. RL A 4. RLC A 5. RR A 6. RL A 7. SWAP A
Memory 12200 12201 12202 12203 12204 Content %D AA EE FF 22 What result is produced in the destination operand by execution the following instruction? a- LEA SI[DI+Bx+5] b- LDS SI.[200]
9. Write a sequence of LEGV8 instructions to do the following: set X8 to 100 if the contents of X1 is an odd number and set X9 to 200 otherwise. Do not use division instruction in you code. Instead, you use an AND instruction to test if a number is even or odd. Comment your assembly code. 10. Write the corresponding LEGV8 code for the following fragment of C code for (int i=0; i<50; ¡++) C=C[i-1]-C[i+1]*9; Assume that the index i is in register X0, C is an integer array and the base address of C is in X2. Comment your assembly code. How many instructions are executed? How many data memory references have been made? I
1. In the following instruction sequence, show the value of AL for each line of code. Write the value in hexadecimal. Instructions Value of AL (H) MOV AL, 01100001B AND AL, 00011101B MOV AL, 12H AND AL, 3BH MOV AL, 00001111B OR AL, 72H MOV AL, 83H XOR AL, 26H
:Q1: Answer the following Write equivalent instruction sequences • using string instruction for the following: MOV AL, [DI] CMP AL, [SI] DEC SI DEC DI إجابتك Write equivalent instruction sequences • using string instruction for the following: MOV AL, [SI] MOV [DI], AL INC SI INC DI إجابتك State the purpose of the instructions CLD, • .STD, CLI, and STI إجابتك
Microprocessor Fundamentals AVR please solution with explain 7) Write a program to do the following: 1- Make all pins of Port C to be Output pins. 2- Make all pins of Port D to be Input pins. 3- Make pin PB5 of Port B to be output pin using SBI or CBI. 4- Make pin PB6 of Port B to be input pin using SBI or CBI. 5- Output the value $25 to Port C. Q8) Write a Main Program to do the following (place it at address $0204): 1- Enable INTO interrupt and disable INT1 interrupt. 2- Make INTO ot be triggered by a rising edge. 3- Set the Global Interrupt Enable flag.
26. Find the time delay in the following program if the crystal frequency is 1 MHz. Do not ignore the time delay due to the first and last instruction. DELAY: LDI R16, 30 AGAIN: LDI R17, 35 HERE: NOP NOP DEC R17 BRNE HERE DEC R16 BRNE AGAIN RET