Q2/ Two byte -sized BCD integers are stored at the symbolic offset addresses NO1 and NO2 respectively, Write an instruction sequence to generate their difference and store it at NO3. The difference is to be formed by subtracting the value at NO1 from that at NO2. Assume that all storage locations are in the current data segment.

Q2/ Two byte -sized BCD integers are stored at the symbolic offset addresses NO1 and NO2 respectively, Write an instruction sequence to generate their difference and store it at NO3. The difference is to be formed by subtracting the value at NO1 from that at NO2. Assume that all storage locations are in the current data segment.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
- The stack memory is addressed by a combination of the plus offset. The PUSH and POP instructions always transfer between segment -bit number the stack and a register or memory location in the 8086 microprocessors. For string instructions, DI always addresses data in the segment. The 8086 LOOP instruction decrements register for a 0 to decide if a jump occurs and tests it
Using a K-map, simplify the output expression for the circuit in the figure. Draw the logic diagram for the simplified logic expression derived in the previous procedure. Construct the simplified circuit in the previous procedure. Use a DIP switch for each input.
1. Design a logic circuit with four inputs A,B,C,D as shown in figure1 and one output Y and whose output will be high if only the input is evenly divisible by 3. A B LY D Figure1 I. Find the SOP Boolean expression of the output Y. I. Draw logic circuit using basic gate and verify the result by using any simulation tools. II. Draw a logic circuit by using NAND gate only. |
20. Suppose we have just found yet another representation for floating point numbers. Using this representation, a li2-bit floating point number has 1 bit for the sign of the number, 4 bits for the exponent and 7 bits for the mantissa, which is normalized as in the Simple Model so that the first digit to the right of the radix points must be a 1. Numbers in the exponent are in signed 2's complement representation. No bias is used and there are no implied bits. Show the representation for the smallest positive number this machine can represent using the following format (simply fill in the squares provided). What decimal number does this equate to? : SIGN EXPONENT MANTISSA
8085 microprocessor went through its manipulation operation in the ALU, the results was transferred on the data bus and status of the results was stored in the flag register for indications . With your knowledge and understanding illustrate a complete bit configuration of 8085 flag register and show the functions of the represented bits in the register.
1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
The ASM chart shown in Figure 4 specifies a synchronous sequential logic circuit. Derive a suitable state table from the ASM and design the circuit for the state table using JK flip-flop and logic gates.
How to build this circuit? (on Digital or Logisim) Binary-coded decimal is an alternative method of representing integers using binary. In it, each base-10 digit is represented by four bits, thus each nibble takes one of 10 values (0000 through 1001). Therefore, using BCD, 42 (decimal) is represented as 0100 0010 (binary) and 196 (decimal) is represented as 0001 1001 0110 (binary). Create a circuit in Logisim that accepts as input a pair of two-digit integers represented as BCD and outputs their sum in BCD. Any and all Digital components are fair game. You can assume that all inputs will be valid BCD-encoded numbers.
1. Convert the following 32-bit IEEE single precision floating point number to base-10 representation. (01000011000011001000000000000000)2 = ?
Sketch a circuit to represent the logic AB’C’D using a. a conventional symbol b. an array logic symbol.
Solve the following question. You must show your work. a) What does 962F000016 represent in an IEEE single-precision floating-point number? b) Convert -151o to a 16-bit sign-magnitude representation. c) Convert-151o to a 16-bit two's complement representation. d) Define the system status register value after an instruction execution resulted the following: a. Result was a non-zero value, a negative value, had a carry and extended bits. b. Trace mode was not on and was executed in supervisor mode. C. Any higher interrupt priorities higher than level 3 will be recognized.