4. In a distillation of a mixture of acetone (bp. 56°C and dichloromethane bp. 40°C), a fraction averaging 48°C was collected that never exhibited a plateau temperature. Show using temperature as an indicator of purity what the % of acetone is in this fraction. (Hint: this is similar to the question of refractive index in the last assignment) Please answer very soon will give rating surely

4. In a distillation of a mixture of acetone (bp. 56°C and dichloromethane bp. 40°C), a fraction averaging 48°C was collected that never exhibited a plateau temperature. Show using temperature as an indicator of purity what the % of acetone is in this fraction. (Hint: this is similar to the question of refractive index in the last assignment) Please answer very soon will give rating surely

Macroscale and Microscale Organic Experiments

7th Edition

ISBN:9781305577190

Author:Kenneth L. Williamson, Katherine M. Masters

Publisher:Kenneth L. Williamson, Katherine M. Masters

Chapter4: Recrystallization

Section: Chapter Questions

Problem 1Q

See similar textbooks

Similar questions

In a distillation of a mixture of acetone (bp. 56°C and dichloromethane bp. 40°C), a fraction averaging 48°C was collected that never exhibited a plateau temperature.Show using temperature as an indicator of purity what the % of acetone is in this fraction.(Hint: this is similar to the question of refractive index in the last assignment)
1a. Use the given table to construct a temperature-composition diagram for cyclohexane Toluene mixture. Based on the plot, what is the composition of the distillate obtained by Simple distillation 20 mole percent cyclohexene and 80 mole percent toluene? Show your Work on the plot. 1b. Estimate the composition of the distillate of 20 mole percent of cyclohexane if the Distillation column had three theoretical plates.
in fractional distillation, how do you tell which liquid is in which fraction and which fraction has a mix of liquids if you are trying to seperate cyclohexane and toluene?? what would the density and boiling point of the first fraction be
List and describe two methods that can used to improve the separation of a liquid mixture by fractional distillation
A three-component mixture containing compounds A, B, and C is separated by simple distillation. A fraction from that distillation is collected and analyzed by gas chromatography. The resulting chromatogram is overlaid on a ruler in the figure shown below. Using this figure and the data contained therein, determine the percentage composition of each component in this fraction by the triangulation method (i.e. determine the percentages of A, B, and C in this fraction). Be sure to show the setup for your calculations. 15 10 AAA 5. B 10 15 20 25 30 35 (both axes are in mm)
The liquid-liquid extraction is the classical technique in chemistry to isolate a target component from a mixture. Organic Solvent is the usual solvent being used along with water. TRUE or FALSE
The separation and purification processes given below and the method used against them are given. Which or which of these pairings are correct? Brewing the tea - Extraction Purification of water from impurities-Chromatography Separating olive pomace from oil while olive oil is being produced - Decantation Obtaining oil fractions - Ordinary distillation Obtaining essential oils and using them in perfume making - Water-steam distillation A. I, IV, V B. I, II, III, IV, V C. I, II, V D. I, II, III, V E. I, II, III, IV
Temperature - distillate volume plot for fractional distillation of benzene (b. pt. 80°C) and toluene (b. pt. 110°C ) The area where toluene is being distilled from the mixture. a. cannot be determined. b. FR1 c. FR3 d. FR2
Temperature - distillate volume plot for fractional distillation of benzene (b. pt. 80°C) and toluene (b. pt. 110°C ) The area where benzene is being distilled from the mixture. O a. FR1 b. cannot be determined. c. FR2 d. FR3
IDENTIFICATION OF THE COMPONENTS OF THE MIXTURES. 1. A. Sodium Chloride - naphthalene -'Food Color Mixture 1. Sublimation 2. Adsorption with activated carbon 3. Dissolution with water then evaporation B. Sodium chloride - Sulfur - Sand Mixture 1. Dissolution with water then evaporation 2. Dissolution with toluene then decantation 3. Dissolution with toluene the evaporation
Which statement about liquid-liquid extraction is not correct? * A- A solvent must be available that is miscible with the solution containing the substance to be extracted. B- The solvent used for extraction must have a good ability to dissolve the desired substance. C- The denser solution forms the bottom layer in the extraction funnel. D- The extraction funnel must be vented during the extraction procedure to prevent excessive build-up of pressure inside the extraction funnel. E- All these statements are correct.
In a sample of 90mL of Acetone and 130 mL of Chloroform, What is XAcetone? Please provide detailed explanation, if you can . Also, as a bonus( not required), Is there a relationship between Refractive Index of a Liquid with the mole ration of the liquid.