2. Suppose a voltage v(t) = A sin (300t + A1°) volts is applied to a single phase load and the resulting current is i(t) = B sin (300t - B1°) amperes. Find complex power S, average power P, reactive power Q and circuit power factor. (ii) Find a simple series circuit which exhibits this behavior. (iii) Find a simple parallel circuit that will exhibit this behavior. Activate Windows Go to Settings to activate Wi

2. Suppose a voltage v(t) = A sin (300t + A1°) volts is applied to a single phase load and the resulting current is i(t) = B sin (300t - B1°) amperes. Find complex power S, average power P, reactive power Q and circuit power factor. (ii) Find a simple series circuit which exhibits this behavior. (iii) Find a simple parallel circuit that will exhibit this behavior. Activate Windows Go to Settings to activate Wi

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.
1) Two identical voltage waveforms of difference phase angles are shown in Figure B. Write down the expression of waveforms A and B clearly. HUS Voltage (V) 8 0 K/N B 7: ST ot
Which cannot be said since Z is an inductive load in the circuit given below? A) load voltage period is 0.02sec. B) Load voltage peak value is 311V. C) Load voltage frequency is 50Hz D) Load voltage average value is 220V.
244. The apparent power drawn by an a.c. circuit is 20 kVA and reactive power is 12 kVA. The real power in the circuit in kW will be
Use 3 decimal places and box the final answer. A 4-ohm resistor is in series with a 7.96-mH inductor connected across a 110-V 60-Hz source. Determine : a) the impedance b) the input current c) the voltage across the resistor and the inductor d) Draw the phasor diagram showing the current and the voltages. e) The power factor and the power input to the circuit.
Two impedances consist of resistance of (15 ohms and series connectedinductance of 0.04 henry) and (resistance of 10 ohms, inductance of 0.1 henryand a capacitance of 100 microfarad, all in series) are connected in series andare connected to 230 volts, 50 – Hz AC source. Find: (a) current drawn, (b) voltageacross each impedance, (c) individual and total power factor. Draw the phasordiagram.
A 400 MVA synchronous machine has H, = 4.6 MJ/MVA and a 1200 MVA machine has H₂=3.0 MJ/MVA. The two machines operate in parallel in a power plant. Find out H relative to a 100 MVA base.
Calculate the value of capacitance in the following figure that must be connected in parallel with the load to correct the source power factor to 0.94 lagging. The frequency f = 60 Hz
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation
1 Calculate average and RMS value of the voltage waveform given in Figure. 4V %3D t(ms)- 4V
A Star 3Phase source with phase voltage of 400V at 50HZ is connected to a delta connected 3Phase AC Motor. The transmisson line resistance from source to load terminal is 1 Ohm. The internal resistance of each winding of motor is 9 Ohm and the inductance of each coil is 38.2 mH. What is the true power delivered to load? O A) 15999 B) 14999 C) 13999 O D) None