Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 9, Problem 9.43SP
A short timber post of Douglas fir is subjected to an axial compressive load of 40,000 Ib. The nominal dimensions of the post area are 8 in. by 8 in. Its length is 8 ft-6 in. Assume a proportional limit of 6000 psi. Using dressed dimensions, compute
(a) stress
(b) strain
(c) total deformation
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
In constructing a large mobile, Jude hangs an aluminum sphere of mass 6.0kg from a vertical steel wire 0.50m long and 2.5x10^−3 cm^2 in cross-sectional area. On the bottom of the sphere, he attaches a similar steel wire, from which he hangs a brass cube of mass 10.0kg. For each wire, compute:
(a) The tensile strain and(b) The elongation
In constructing a large mobile, Jude hangs an aluminum sphere of mass 6.0kg from a vertical steel wire 0.50m long and 2.5 x10−3 cm2 in cross-sectional area. On the bottom of the sphere, he attaches a similar steel wire, from which he hangs a brass cube of mass 10.0kg. For each wire, compute:(a) The tensile strain and(b) The elongation
A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 m is under tension. If the wire length extension is 2.5 mm, calculate the stress in the wire. Give your answer in N/m2to 2 decimal places. (show all work)
Chapter 9 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 9 - Write the direct stress formula in its three forms...Ch. 9 - A 6-in-diameter concrete test cylinder is loaded...Ch. 9 - Determine the tensile stress in each segment of...Ch. 9 - Calculate the stress developed in the following...Ch. 9 - The following members are subjected to axial...Ch. 9 - Determine the stresses in the two segments of the...Ch. 9 - A bin weighing 8 tons is supported by three steel...Ch. 9 - Diameters of small commercially available steel...Ch. 9 - A No. 32 (metric designation) reinforcing bar for...Ch. 9 - In the bolted connection of Figure 9.12 , assume...
Ch. 9 - Compute the force required to punch a...Ch. 9 - The 34 — in. — diameter bolt shown is subjected to...Ch. 9 - Why is strain unitless (or dimensionless)?Ch. 9 - (a) Given =1.2in. and L=100ft calculate (b) Given...Ch. 9 - A short compression member 2 in. by 2 in. in cross...Ch. 9 - A 100-ft-long rod is suspended from one end. The...Ch. 9 - Compute the total elongation of a steel bar,...Ch. 9 - A steel rod 34 in. in diameter and 25 ft long is...Ch. 9 - An aluminum rod 25mm in diameter and 4m long is...Ch. 9 - A steel rod 10 ft long is made up of two 5 ft...Ch. 9 - A titanium alloy bar elongates 0.500 in. when...Ch. 9 - Write a program that will calculate the allowable...Ch. 9 - Write a program that will compute stress, strain,...Ch. 9 - The Viking Bin Company manufactures suspended bins...Ch. 9 - Write a computer program that will calculate the...Ch. 9 - The joint between a diagonal and a chord in a...Ch. 9 - In Problem 9.26, find the required length of the...Ch. 9 - A column is supported by a base plate, pedestal,...Ch. 9 - If the soil pressure under the footing of Problem...Ch. 9 - A hopper weighing 75 kN is supported by three...Ch. 9 - A steel bar has a rectangular cross section 25 mm...Ch. 9 - A steel wire is suspended vertically from its...Ch. 9 - A W1240 shape is subjected to a tensile load of...Ch. 9 - Calculate the required diameter of steel tie rods...Ch. 9 - A 30-ft-long steel rod of circular cross section...Ch. 9 - Consider the bolted lap joint shown in Figure...Ch. 9 - An inclined member is braced with a glued block,...Ch. 9 - Calculate the force a punch press must exert if it...Ch. 9 - A 34 - in. - diameter punch is used to punch a...Ch. 9 - A control arm is keyed to a 1-in. -diameter shaft...Ch. 9 - Calculate the required width b for the key of...Ch. 9 - A 25-mm-diameter aluminum rod, 3 m long, is...Ch. 9 - A short timber post of Douglas fir is subjected to...Ch. 9 - A 1 00-ft surveyor’s steel tape with a...Ch. 9 - An 18-in-long steel rod is subjected to a tensile...Ch. 9 - Compute the magnitude of the tensile load that...Ch. 9 - A 5-mm-diameter steel wire, 18 m in length, is...Ch. 9 - A structural steel rod 112 in. in diameter and 20...Ch. 9 - A rectangular structural steel eyebar 34 in. thick...Ch. 9 - 9.50 A
in. — diameter steel rod, 100 ft long, is...Ch. 9 - For the truss shown, compute the total deformation...Ch. 9 - A steel bar with a cross section of 12 in. by 12...Ch. 9 - Rework Problem 9.52 , changing the second load...Ch. 9 - In the structure shown, the tie-back BC is a round...Ch. 9 - A hook is suspended by two steel wires, as shown....Ch. 9 - The trolley of a small hoist is supported on a...Ch. 9 - The steel piston rod to the master cylinder has a...Ch. 9 - A stranded steel brake cable is composed of 7...Ch. 9 - The piston of a steam engine is 400 mm in diameter...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- (a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressurearrow_forwardCalculate the smallest area of each cable if the stress is not to exceed 76 000 KPa in bronze and 118 MPa in steel if a homogeneous 778 000 g bar AB is supported at either end by a cable.arrow_forwardA slab of granite countertop is subjected to a tensile force of 3.3 kN, as illustrated below. What are the changes in the axial (2075 mm), width (500 mm), and thickness (16 mm) direction? Assume n = 0.25. E = 53,000 MPa.arrow_forward
- A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 mis under tension. If the wire length extension is 2.5 mm, calculate the stress in thewire. Give your answer in N/m2to 2 decimal places.arrow_forwardA rosette consisting of 3 gages forming, respectively, angles of θa, θb and θc with the x-axis is attached to the free surface of machine components made of material with a given Poisson’s ratio v and Modulus of elasticity E as shown in Fig. 6. Take note that strain values given above are the gage readings and not principal strains.arrow_forwardFor a steel circular cantilever beam, 10mm in diameter, 700mm in length with an applied load of 7.848N in the free end, produce a sketch showing the distribution of stresses across the beam section for an applied moment of M=(3/4My+1/3Mp). Where My=24543.5 N.mm and Mp=41666.66667 N.mm and yeild stregth of material is 250Mpa. Cheersarrow_forward
- a copper-rolled wire 10 m long and 1.5mm in diameter when supporting a weight of 35.7 kg, elongates 1.36 cm. Compute the stress (kg/cm^2), strain, and the value of the Young's modulus of elasticity for this wire.arrow_forwardCalculate the resulting stress in an aluminum wire, 4-m long and 2.6 mm in diameter, if a 12.5 -kg fixture is hung from the wire? Young's modulus for aluminum is 7.0 × 10^10 N/m^2. Express the answer in Pa and as a whole number.arrow_forwardA rosette consisting of 3 gages forming, respectively, angles of θa, θb and θc with the x-axis is attached to the free surface of machine components made of material with a given Poisson’s ratio v and Modulus of elasticity E as shown in Fig. 6. Take note that strain values given above are the gage readings and not principal strains. PLEASE ANSWER I,G,Harrow_forward
- Find stress of a aluminum cylinder of diameter 12.8mm and gauge length 50.8mm. The force applied is 47,500N.arrow_forwardA short rectangular-sectioned timber post has one side of its section twice the other. When 9.542 kN is applied axially to the post, it contracts by 0.174 mm per metre length. Calculate the maximum cross-sectional dimension in mm of the post if the Young's modulus for timber is 8.176 GPaarrow_forwardTake E 200 GPa for bar material,A conical tapering bar u from a diameter of 4 cm to 15 cm is given, It has a length of 40 cm. If an axial force of 80 KN is applied at each end of the bar, calculate the elongation of the bar.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
EVERYTHING on Axial Loading Normal Stress in 10 MINUTES - Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=jQ-fNqZWrNg;License: Standard YouTube License, CC-BY