Fluid Mechanics
8th Edition
ISBN: 9780073398273
Author: Frank M. White
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 5, Problem 5.41P
A certain axial flow turbine has an output torque M that is proportional to the volume flow rate Q and also depends on the density
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A one-fifth scale model of a water turbine is tested in a laboratory at T = 20°C. The diameter of the model is 8.0 cm, its volume flow rate is 17.0 m3 /h, it spins at 1500 rpm, and it operates with a net head of 15.0 m. At its best efficiency point, it delivers 450 W of shaft power. Calculate the efficiency of the model turbine. What is the most likely kind of turbine being tested?
A certain SSSF control volume with a single inflow and outflow
and has an inflow speed V₁ = 200 meters / sec and outflow speed Ve = 1000
meters / sec, with a mass-flow-rate m(dot) = 5 kg/ sec. Find the time rate of
change of the kinetic energy between the outflow and inflow streams in kW
(units must be correct).
In this question, assume the "additional displacement" is in the positive u direction.
A mass weighing 16 lbs stretches a spring 8 inches. The mass is in a medium that exerts a viscous resistance
of 1 lbs when the mass has a velocity of 2 ft/sec.
Suppose the object is displaced an additional 5 inches and released.
Find an equation for the object's displacement, u(t), in feet after t seconds.
u(t) =
Chapter 5 Solutions
Fluid Mechanics
Ch. 5 - Prob. 5.1PCh. 5 - A prototype automobile is designed for cold...Ch. 5 - P5.3 The transfer of energy by viscous dissipation...Ch. 5 - When tested in water at 20°C flowing at 2 m/s, an...Ch. 5 - P5.5 An automobile has a characteristic length and...Ch. 5 - P5.6 The disk-gap-band parachute in the...Ch. 5 - Prob. 5.7PCh. 5 - Prob. 5.8PCh. 5 - The Richardson number, Ri, which correlates the...Ch. 5 - Prob. 5.10P
Ch. 5 - Prob. 5.11PCh. 5 - The Stokes number, St, used in particle dynamics...Ch. 5 - Prob. 5.13PCh. 5 - Flow in a pipe is often measured with an orifice...Ch. 5 - The wall shear stress T in a boundary layer is...Ch. 5 - P5.16 Convection heat transfer data are often...Ch. 5 - If you disturb a tank of length L and water depth...Ch. 5 - Prob. 5.18PCh. 5 - Prob. 5.19PCh. 5 - Prob. 5.20PCh. 5 - Prob. 5.21PCh. 5 - As will be discussed in Chap. 11, the power P...Ch. 5 - The period T of vibration of a beam is a function...Ch. 5 - Prob. 5.24PCh. 5 - The thrust F of a propeller is generally thought...Ch. 5 - A pendulum has an oscillation period T which is...Ch. 5 - Prob. 5.27PCh. 5 - Prob. 5.28PCh. 5 - P5.29 When fluid in a pipe is accelerated linearly...Ch. 5 - Prob. 5.30PCh. 5 - P5.31 The pressure drop per unit length in...Ch. 5 - A weir is an obstruction in a channel flow that...Ch. 5 - Prob. 5.33PCh. 5 - Prob. 5.34PCh. 5 - Prob. 5.35PCh. 5 - Prob. 5.36PCh. 5 - Prob. 5.37PCh. 5 - Prob. 5.38PCh. 5 - Prob. 5.39PCh. 5 - Prob. 5.40PCh. 5 - A certain axial flow turbine has an output torque...Ch. 5 - When disturbed, a floating buoy will bob up and...Ch. 5 - Prob. 5.43PCh. 5 - Prob. 5.44PCh. 5 - P5.45 A model differential equation, for chemical...Ch. 5 - P5.46 If a vertical wall at temperature Tw is...Ch. 5 - The differential equation for small-amplitude...Ch. 5 - Prob. 5.48PCh. 5 - P5.48 A smooth steel (SG = 7.86) sphere is...Ch. 5 - Prob. 5.50PCh. 5 - Prob. 5.51PCh. 5 - Prob. 5.52PCh. 5 - Prob. 5.53PCh. 5 - Prob. 5.54PCh. 5 - Prob. 5.55PCh. 5 - P5.56 Flow past a long cylinder of square...Ch. 5 - Prob. 5.57PCh. 5 - Prob. 5.58PCh. 5 - Prob. 5.59PCh. 5 - Prob. 5.60PCh. 5 - Prob. 5.61PCh. 5 - Prob. 5.62PCh. 5 - The Keystone Pipeline in the Chapter 6 opener...Ch. 5 - Prob. 5.64PCh. 5 - Prob. 5.65PCh. 5 - Prob. 5.66PCh. 5 - Prob. 5.67PCh. 5 - For the rotating-cylinder function of Prob. P5.20,...Ch. 5 - Prob. 5.69PCh. 5 - Prob. 5.70PCh. 5 - The pressure drop in a venturi meter (Fig. P3.128)...Ch. 5 - Prob. 5.72PCh. 5 - Prob. 5.73PCh. 5 - Prob. 5.74PCh. 5 - Prob. 5.75PCh. 5 - Prob. 5.76PCh. 5 - Prob. 5.77PCh. 5 - Prob. 5.78PCh. 5 - Prob. 5.79PCh. 5 - Prob. 5.80PCh. 5 - Prob. 5.81PCh. 5 - A one-fiftieth-scale model of a military airplane...Ch. 5 - Prob. 5.83PCh. 5 - Prob. 5.84PCh. 5 - *P5.85 As shown in Example 5.3, pump performance...Ch. 5 - Prob. 5.86PCh. 5 - Prob. 5.87PCh. 5 - Prob. 5.88PCh. 5 - P5.89 Wall friction Tw, for turbulent flow at...Ch. 5 - Prob. 5.90PCh. 5 - Prob. 5.91PCh. 5 - Prob. 5.1WPCh. 5 - Prob. 5.2WPCh. 5 - Prob. 5.3WPCh. 5 - Prob. 5.4WPCh. 5 - Prob. 5.5WPCh. 5 - Prob. 5.6WPCh. 5 - Prob. 5.7WPCh. 5 - Prob. 5.8WPCh. 5 - Prob. 5.9WPCh. 5 - Prob. 5.10WPCh. 5 - Given the parameters U,L,g,, that affect a certain...Ch. 5 - Prob. 5.2FEEPCh. 5 - Prob. 5.3FEEPCh. 5 - Prob. 5.4FEEPCh. 5 - Prob. 5.5FEEPCh. 5 - Prob. 5.6FEEPCh. 5 - Prob. 5.7FEEPCh. 5 - Prob. 5.8FEEPCh. 5 - In supersonic wind tunnel testing, if different...Ch. 5 - Prob. 5.10FEEPCh. 5 - Prob. 5.11FEEPCh. 5 - Prob. 5.12FEEPCh. 5 - Prob. 5.1CPCh. 5 - Prob. 5.2CPCh. 5 - Prob. 5.3CPCh. 5 - Prob. 5.4CPCh. 5 - Does an automobile radio antenna vibrate in...Ch. 5 - Prob. 5.1DPCh. 5 - Prob. 5.2DP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Given and Solution A hydro turbine operates with a head of 50 m of water. Inlet and outlet conduits are 2 m in diameter. Estimate the mechanical power developed by the turbine for an outlet velocity of 5 m⋅s−1.arrow_forwardAn air fan has a bladed rotor of 12 in outside diameter and 10 in inside diameter. The height of each rotor blade is a constant 1.0 in from blade inlet to blade outlet, that flowrate is steady on a time average basis. At 230 ft3/min and the absolute velocity of the air at blade inlet V1 is radial, The blade discharge angle is 30 ° from the tangential direction. If the rotor rotates at a constant speed of 1725 RPM estimate the power required to run the fan. (ans: 0.0972 hp)arrow_forwardA Francis radial-flow hydro turbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 2 m, rı = 1.34 m, b2 = 0.8 m, and bi = 2.2 m. The runner blade angles are ß = 82° and Bi = 46° at the turbine inlet and outlet, respectively (Figure 3.1). The runner rotates at n = 120 rpm. The volume flow rate at design conditions is 300 m³/s. Irreversible losses are neglected in this preliminary analysis. i. Calculate the angle æ wicket gate should turn the flow, where æ is measured from the radial direction at the runner inlet. ii. Calculate the swirl angle, a, where a is measured from the radial direction at the runner outlet. iii. Does this turbine have a forward or reverse swirl? iv. Predict the power output (kW) and required net head (m).arrow_forward
- The 100 mm diameter pulley on a generator is being turned by a belt moving 20 m/s and accelerating 6m/s^2. A fan with an outside diameter of 150 mm is attached to the pulley shaft. What are the linear velocity and acceleration of the tip of the fan?arrow_forwardA piston moves with constant velocity U0 in a cylinder having radius R. A liquid having density leaves the open end with conical velocity proÖle V~ = V0(1-r/R)^k.Figure for problem 1.(a) If the exhaust port is closed, find the value of V0 in terms of U0. Be sure to define an appropriate control volume for solving this problem.(b) If V0 = U0, find the volume áow rate leaving through the exhaust port (in terms of U0 and R)arrow_forwardWater steam is running through the nozzle. Inlet pressure is P1=25 bars; T1=300C; V1=90m/s; A1=0.2m2. The exit parameters are: P2=11bars; T2=210C. The mass flow rate is m=2 kg/s. Determine: a.Exit velocity V2=?; b.Inlet and outlet diameters D1 and D2. show all stepsarrow_forward
- Q2/ An outward flow reaction turbine has tangential velocity at its inner rim as 20 m/s, and ratio of radii is 0.9. The turbine is placed 1 m below the water surface and blade angle are 90° and 20° at inlet and outlet respectively. The radial velocity of flow at inlet is 6 m/s. Neglecting frictional losses and taking the discharge as radial, draw velocity triangles at inlet and outlet and find: (a) guide vane angle (b) the velocity of water from the guides. (c) total head of water (d) hydraulic efficiencyarrow_forwardImagine the water level in the tank as shown in the Figure rises at a rate of 0.004579 ft³/sec. then find: i) The volume flowrate of water leaving the tank (Q3) in ft³/s from pipe 3. ii) The average velocity of water leaving the tank (V3) in ft/s from pipe 3. Pipe 1: Qi=0.0109 ft²/s Pipe 2: Q₂ = 0.025 ft³/s Pipe 3: dy = 1.5 in. V₁ = ?! Q₁ =?arrow_forwardA single-stage axial flow pump with outer radius r2 =0.240 m and inner radius r1=0.120 m is given. At a radius of r =0.090 m, absolute flow flows in from the axial direction just before the impeller inlet and relative flow flows out in the axial direction just after the impeller outlet. Assuming a flow rate Q = 0.265 m^3/s, a water density p = 1.000 x 103 kg/m^3, a rotation speed n=2.4 x 10^3 rpm, and a gravitational acceleration g = 9.81 m/s^2, and assuming that the theoretical head Hth = W/g (W: specific work) derived from Euler's law is constant at all impeller radii, answer the following questions. (1) Assuming that the flow is uniform, find the axial velocity. (2) Find the velocity triangles just before the impeller inlet and just after the impeller outlet at a radius of r =0.09 m.arrow_forward
- A single-stage axial flow pump with outer radius r2 =0.240 m and inner radius r1=0.120 m is given. At a radius of r =0.090 m, absolute flow flows in from the axial direction just before the impeller inlet and relative flow flows out in the axial direction just after the impeller outlet. Assuming a flow rate Q = 0.265 m^3/s, a water density p= 1.000 x 103 kg/m^3, a rotation speed n = 2.4 x 10^3 rpm, and a gravitational acceleration g = 9.81 m/s^2, and assuming that the theoretical head Hth = W/g (W: specific work) derived from Euler's law is constant at all impeller radii, answer the following questions. (1) Assuming that the flow is uniform, find the axial velocity. (2) Find the velocity triangles just before the impeller inlet and just after the impeller outlet at a radius of r =0.09 m. (3) From Euler's law, find the theoretical head Hth [m]. (4) Find the power P [W] required to rotate the impeller (drive the pump).arrow_forwardA single-stage axial flow pump with outer radius r2 = 0.240 m and inner radius r1=0.120 m is given. At a radius of r =0.090 m, absolute flow flows in from the axial direction just before the impeller inlet and relative flow flows out in the axial direction just after the impeller outlet. Assuming a flow rate Q = 0.265 m^3/s, a water density p = 1.000 x 103 kg/m^3, a rotation speed n = 2.4 x 10^3 rpm, and a gravitational acceleration g = 9.81 m/s^2, and assuming that the theoretical head Hth = W/g (W: specific work) derived from Euler's law is constant at all impeller radii, answer the following questions. (1) Looking at the following image, find all values of the velocity triangle just before the impeller inlet and just after the impeller outlet at radius r =0.09 m. impeller Figure 37.1 A propeller of an axial flow pump a₁ w1 U₁ Outlet guide vane B₁ Impeller α₂ Vw2 U₂=U₂=Uarrow_forwardAn artery reduces in area from 0.00034 m2 at its inlet to 0.00022 m2 at its outlet. Blood enters the artery at velocity 0.15 m/s and pressure 15,000 Pa. Blood leaves the artery at a pressure 10,000 Pa. Assuming that the artery may be modelled as a straight, circular tube and neglecting gravity what is the force exerted on the artery by the fluid. The density of blood is 1050 kg/m3. Give your answer in Newtons.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license