Traffic and Highway Engineering
5th Edition
ISBN: 9781305156241
Author: Garber, Nicholas J.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 18, Problem 5P
Given the specifications for an asphaltic concrete mixture and the results of a sieve analysis, determine the proportion of different aggregates to obtain the required gradation.
Coarse aggregates: 60%
Fine aggregates: 35%
Filler: 5%
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Laboratory specific gravity and absorption tests are run on two coarse aggregate sizes, which have to be blended. The results are as follows:Aggregate A: Bulk specific gravity = 2.814; Absorption = 0.4% Aggregate B: Bulk specific gravity = 2.441; Absorption = 5.2% a. What is the specific gravity of a mixture of 50% aggregate A and 50% aggregate B by weight? b. What is the absorption of the mixture?
Laboratory specific gravity and absorption tests are run on two coarse aggregate sizes, which have to be blended. The results are as follows:Aggregate A: Bulk specific gravity = 2.491; absorption = 0.8,Aggregate B: Bulk specific gravity = 2.773; absorption = 4.6,a. What is the specific gravity of a mixture of 60% aggregate A and 40% aggregate B by weight?b. What is the absorption of the mixture?
A portland cement concrete mix requires mixing sand having a gradationfollowing the midpoint of the ASTM gradation band (Table 5.4) and gravelhaving a gradation following the midpoint of size number 467 of the ASTMgradation band (Table 5.5) at a ratio of 2:3 by weight. On a 0.45 power gradation chart, plot the gradations of the sand, gravel, and the blend. Is the gradation of the blend well graded? If not, what would you call it?
Chapter 18 Solutions
Traffic and Highway Engineering
Ch. 18 - Prob. 1PCh. 18 - Prob. 2PCh. 18 - Prob. 3PCh. 18 - Prob. 4PCh. 18 - Given the specifications for an asphaltic concrete...Ch. 18 - Given the particle size distributions of two...Ch. 18 - Given the particle size distributions of two...Ch. 18 - Given four different types of aggregates to be...Ch. 18 - Prob. 9PCh. 18 - Prob. 10P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- Laboratory specific gravity and absorption tests are run on two coarse aggregate sizes, which have to be blended. The results are as follows: Aggregate A: Buck specific gravity = 2.395; absorption = 4.69% Aggregate B: Buck specific gravity = 2.601; absorption = 0.51% What is the specific gravity of a mixture of 50]% aggregate A and 50% aggregate B by weight?arrow_forwardQ1: Prepare mix design for given data • The 28-day compressive strength should be 34 MPa, The slump should be between 75 mm and 100 mm and the maximum aggregate size should not exceed 19 mm The properties of the materials are as follows: • Cement : Type I, specific gravity = 3.15 • Coarse Aggregate: Bulk specific gravity= 2.65; absorption capacity = 0.5%; dry-rodded unit weight = 1605 kg/m3, surface moisture = 1% • Fine Aggregate: Bulk specific gravity= 2.60; absorption capacity = 1.1%; fineness modulus = 2.70; surface moisture = 3%arrow_forwardDesign a Mix for the following Data. Specified strength = (99.5) MPa, Required Slump = 80 mmMaximum size of aggregate = 25 mm, FM of fine aggregate = 2.40Grading of aggregate as satisfied by ASTM C33 (American Society for Testing and Materials)SSD specific gravity of fine and coarse aggregate = 2.75Rodded bulk density of coarse aggregate = 1600 kg/cubic mAbsorption Capacity of coarse aggregate = 0.9 %Absorption Capacity of fine aggregate = 0.5 %Moisture Content of fine and coarse aggregate = 2 %Exposure Conditions = Normalarrow_forward
- 2.638, 2.514, 2.437 O 2.651, 2.472, 2.364arrow_forward46.5 kg of fine aggregate is mixed with 72.3 kg of coarse aggregate. The fine aggregate has a moisture content of 2.0% and its absorption is 3.4% whereas the coarse aggregate has a moisture content of 1.3% and its absorption is 3.0%. Determine the amount of water required to increase the moisture content so that there is 1% free moisture in the aggregate blend.arrow_forwardA compacted asphalt concrete specimen has the following propertiesAsphalt Content = 5% by total weight of the mixBulk specific gravity of the mix = 2.485Theoretical maximum specific gravity = 2.595Bulk specific gravity of the aggregate = 2.715Absorption = 1.5%Compute the percent's VTM, VMA, and VFAarrow_forward
- 500 gm oven dry fine aggregate was tested to find its physical properties. The output from the test was as follows: SSD = 510 gm, mass of the vessel full of water = 1200 gm, mass of vessel plus sand and topped up with water= 1500 gm, mass in wet condition 518 gm, Apparent specific gravity= 2.5 . The grading of the fine aggregate is in the table below. Answer the followings: 1-Moisture content % is 2- The mass of oven dried sand isarrow_forwardThe mix design for an asphalt concrete mixture requires 2 to 6% minus 0.075 mm. The three aggregates shown in Table P.5.34 are available. TABLE P5.34 Minus 0.075 mm Coarse 0.5% Intermediate 1.5% Fine Aggregate 11.5% Considering that approximately equal amounts of coarse and intermediate aggregate will be used in the mix, what is the percentage of fine aggregate that will give a resulting minus 0.075 mm in the mixture in the middle of the range, about 4%?arrow_forwardDiscuss five different desirable characteristics of aggregate used in asphalt concrete.arrow_forward
- According to ACI 211 we require a mix with a mean 28-day compressive strength (measured on standard cylinders) of 40MPa and a slump of 25 mm, Q1 ordinary Portland cement being used. The maximum size of well-shaped, angular aggregate is 10 mm, its bulk density is 1700 kg/m3, and its specific gravity is 2.7. The available fine aggregate has a fineness modulus of 2.60 and a specific gravity of 2.58. No air entrainment is required.arrow_forwardThoroughly mix the aggregate sample and reduce it to an amount suitable for testing, using a sample splitter or by quartering. The minimum sample size should be as follows: Minimum Mass, kg Fine aggregate with at least 95% passing 2.36-mm sieve 0.1 Fine aggregate with at least 85% passing 4.75-mm sieve 0.5 Coarse aggregate with a nominal maximum size of 9.5 mm 1 Coarse aggregate of a nominal maximum size of 12.5 mm 2 Coarse aggregate of a nominal maximum size of 19.0 mm Coarse aggregate of a nominal maximum size of 25.0 mm 10 Coarse aggregate of a nominal maximum size of 37.5 mm 15arrow_forwardIn proportioning a concrete mix, the coarse and fine aggregates had the following properties respectively; Coarse: Dry weight: 800lb, 3,2% MC, 2.0% AC, Fine: Dry weight 350 lb, 1.2% MC, 2.9% AC. How much should the water be adjusted to account for the agregate moisture?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Traffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning
Aggregates: Properties; Author: nptelhrd;https://www.youtube.com/watch?v=49yGZYeokKM;License: Standard YouTube License, CC-BY