Applied Fluid Mechanics (7th Edition)
7th Edition
ISBN: 9780132558921
Author: Robert L. Mott, Joseph A. Untener
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 17, Problem 17.13PP
A bulk liquid transport truck incorporates a cylindrical tank
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A bulk liquid transport truck incorporates a cylindrical tank 3m in diameter and 10m long. For the tank alone, calculate the pressure drag when the truck is traveling at 80km/h in air at 0°C
a smooth flat plate of length 5 m and width 2 m is moving with a velocity of 4 m/s in stationary air of density as 1.25 kg/m³ and kinematic viscosity 1.5 x 10-5 m²/s. determine thickness of the boundary layer at the trailing edge of the smooth plate. find the total drag on one side of the plate assuming that the boundary layer is turbulent from the very beginning.
A flagpole 16 m high has the shape of a
cylinder 100 mm in diameter. The air temperature is 30°C
and the atmospheric pressure is 101 KPaa. With what
speed is the air blowing against the pole if the moment
developed at the base is 2.7 KN.m? The drag coefficient is
1.3.
Chapter 17 Solutions
Applied Fluid Mechanics (7th Edition)
Ch. 17 - A cylinder 25 mm in diameter is placed...Ch. 17 - As part of an advertising sign on the top of a...Ch. 17 - Determine the terminal velocity (see Section 2.6.4...Ch. 17 - Calculate the moment at the base of a flagpole...Ch. 17 - A pitcher throws a baseball without spin with a...Ch. 17 - A parachute in the form of a hemispherical cup 1.5...Ch. 17 - Calculate the required diameter of a parachute in...Ch. 17 - A ship tows an instrument in the form of a 30...Ch. 17 - A highway sign is being designed to withstand...Ch. 17 - Assuming that a semitrailer behaves as a square...
Ch. 17 - A type of level indicator incorporates four...Ch. 17 - Prob. 17.12PPCh. 17 - A bulk liquid transport truck incorporates a...Ch. 17 - A wing on a race car is supported by two...Ch. 17 - Prob. 17.15PPCh. 17 - The four designs shown in Fig. 17.16 for the cross...Ch. 17 - Prob. 17.17PPCh. 17 - Prob. 17.18PPCh. 17 - An antenna in the shape of a cylindrical rod...Ch. 17 - Prob. 17.20PPCh. 17 - Prob. 17.21PPCh. 17 - Prob. 17.22PPCh. 17 - Assume that curve 2 in Fig. 17.5 is a true...Ch. 17 - Prob. 17.24PPCh. 17 - Prob. 17.25PPCh. 17 - A small, fast boat has a specific resistance ratio...Ch. 17 - Prob. 17.27PPCh. 17 - Assume that Fig. 17.11 shows the performance of...Ch. 17 - Calculate the total drag on an airfoil that has a...Ch. 17 - Prob. 17.30PPCh. 17 - Prob. 17.31PPCh. 17 - Prob. 17.32PPCh. 17 - Prob. 17.33PP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A rotary mixer is constructed from two circular disks as shown. The mixer is rotated at 60 rpm in a large vessel containing a brine solution (SG = 1.1, μbrine=1.07×10-3 Pa-s). Determine the appropriate coefficient of drag using Low Reynolds Drag Coefficient. Neglect the drag on the rods and the motion induced in the liquid. Estimate the minimum torque and power required to drive the mixer. only HANDWRITTEN answer needed ( NOT TYPED)arrow_forwardAir flows parallel to the surface of a smooth flat plate 10 m long. The boundary thickness at the leading edge. The Reynolds number at the trailing edge of the plate is 107. Calculate the total drag force due to skin friction on one side of the plate per unit width. Assume that for laminar boundary layer, up to Re, = 5 x 105, the skin friction coefficient is Gr 1.328(Re)-1/2 and for turbulent boundary layer 0.078(Re)-1/5. Take the density of air as 1.2 kg/m³ and Its dynamic viscosity as 1.8 x 10-5 kg/msarrow_forwardTwo large fixed parallel planes are 12 mm apart. The space between the surfaces Example is filled with oil of viscosity 0.972 N.s/m². A flat thin plate 0.25 m² area moves through the oil at a velocity of 0.3 m/s. Calculate the drag force: (1) When the plate is equidistant from both the planes, and (ii) When the thin plate is at a distance of 4 mm from one of the plane surfaces. Fixed parallel plane 6 mm Plate 0.3 m/s F 6 mm 12 mmarrow_forward
- Atmospheric air at 20°C flows at 10 m/s on both sides over a 2-m long by 4-m wide flat plate. Calculate the maximum boundary layer thickness and the drag force if the plate is smooth and if rough.arrow_forwardplate 450 mm x 150 mm has been placed longitudinally in a stream of crude oil (specific gravity 0.925 and kinematic viscosity of 9.0 x 10-5 m2/s) which flows with velocity of 6 m/s. Calculate: (i) the friction drag on the plate; (ii) the thickness of the boundary layer at a distance 215 mm from the trailing edge;(iii) the thickness of the boundary layer at the trailing edge; (iv) shear stress at the trailing edge.arrow_forwardA helicopter is hovering at an altitude where the density of air is 1.165 kg/m³. The helicopter rotor disc has a diameter of 9 m and is rotating at 466 rpm, with the blades having a chord of 0.16 m. Estimate the drag force in newtons per unit span along an elemental strip at the mid-span of the blade. You may assume the drag coefficient of the blade at the mid-span is 0.025.arrow_forward
- A square flat plate with sides of length L 2m and a negligible thickness (out of the page) is held stationary in a stream of air that is moving steadily at standard conditions past the plate with a speed U = 10 m/s that is uniform except for the boundary layers. Assume the plate is oriented so that only friction drag is important. Determine the drag coefficient for this plate. Answer: CD, ≈ 0.003 = U L-arrow_forwardIn the vertical wind tunnel used in paratrooper training, find the wind tunnel free speed required to keep a 75 kg person suspended in the air in a horizontal position. The height of this person is 1.7m and the width is 38cm and the front drag coefficient is around 1. Atmospheric pressure and temperature inside the tunnel are Patm = 85kPa and T = 25C, respectively.arrow_forwardQ1 A car is traveling at sea level at a constant speed. It weighs 2500-lbs, has a frontal area of 20 ft² and has a 90% drivetrain efficiency. Its engine runs at 4000 rev/min, producing 168 ft-lb of torque. The drive axle slippage of 2%, 14-inch-radius wheels, and an overall gear reduction ratio of 2.5 to 1. What is its drag coefficient?arrow_forward
- The two spheres stand with a stop element as in the figure. The spheres are connected with negligible weight rod. What is the minimum air velocity U (m/s] for rotating of the spheres? (Note: Take par=1.225 kg/m, Prater-998 kg/m and u=1.78*10 kg/ms. Spheres are made of steel material with SG=5,41. Take drag coefficient of spheres is 0,41). D=2 cm 10 cm Hinge Stop 45 10cm D-Icmarrow_forwardThe drag coefficient for a car with a frontal area of 26 ft? is being measured in an 8 ft x 8 ft wind tunnel. The density of air under the test conditions is 2.4 x 10 3 slugs/ft, When the air flow rate is, 500,000 ft/min, the drag force on the car was measured to be 170 lb. The drag coefficient under the test conditions is most nearly O 0.30 O 0.32 O 0.28 O 0.34arrow_forwardQuestion B3 – External Flow The rectangular wings of a microlight aircraft have a combined spanwise length of 9.144 m and streamwise (direction of air flow) width of 0.9144 m The wings have a coefficient of form drag of 0.01 and a lift coefficient of 0.3 in cruise. When cruising at a speed of 15Okm/h and altitude of 3,000 feet, the temperature and absolute pressure of the atmospheric air are 5°C and 90 kPa, respectively. a) Calculate the density of the air at cruising altitude. b) Calculate the form drag on the wings. c) Calculate the Reynolds number of the wings.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Ficks First and Second Law for diffusion (mass transport); Author: Taylor Sparks;https://www.youtube.com/watch?v=c3KMpkmZWyo;License: Standard Youtube License