Physics for Scientists and Engineers
6th Edition
ISBN: 9781429281843
Author: Tipler
Publisher: MAC HIGHER
expand_more
expand_more
format_list_bulleted
Question
Chapter 12, Problem 60P
(a)
To determine
To Find:The ratio of
(b)
To determine
To Show:
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
In the figure, the inclined surface is smooth, the cable is tangent to the wheel. Determine the frictional force between the wheel and the horizontal plane required to stabilize the system, assuming the friction between, the horizontal, the plane and the wheel, is adequate.
The given values in the figure are 100kg. 3m. 8m. dim and 60 degrees
During steady motion of a vehicle on a level road, the power delivered to thewheels is used to overcome aerodynamic drag and rolling resistance (the product of the rollingresistance coefficient and the weight of the vehicle), assuming that the friction at the bearingsof the wheels is negligible. Consider a car that has a total mass of 950 kg, a drag coefficient of0.32, a frontal area of 1.8 m2, and a rolling resistance coefficient of 0.04. The maximum powerthe engine can deliver to the wheels is 80 kW. Use the air density of 1.20 kg/m3.a. Determine the speed at which the rolling resistance is equal to the aerodynamic drag force.b. Determine the maximum speed of this car.
he figure shows an outstretched arm (0.61 m in length) that is parallel to
the floor. The arm is pulling downward against the ring attached to the
pulley system, in order to hold the 98-N weight stationary. To pull the arm
downward, the latissimus dorsi muscle applies the force M in the figure,
at a point that is 0.069 m from the shoulder joint and oriented at an angle
of 29°. The arm has a weight of 42 N and a center of gravity (cg) that is
located 0.28 m from the shoulder joint. Find the magnitude of force M.
Axis at
houlder
joint
29°
M
0.28 m
0.069 m
0.61 m
cg
98 N
Chapter 12 Solutions
Physics for Scientists and Engineers
Ch. 12 - Prob. 1PCh. 12 - Prob. 2PCh. 12 - Prob. 3PCh. 12 - Prob. 4PCh. 12 - Prob. 5PCh. 12 - Prob. 6PCh. 12 - Prob. 7PCh. 12 - Prob. 8PCh. 12 - Prob. 9PCh. 12 - Prob. 10P
Ch. 12 - Prob. 11PCh. 12 - Prob. 12PCh. 12 - Prob. 13PCh. 12 - Prob. 14PCh. 12 - Prob. 15PCh. 12 - Prob. 16PCh. 12 - Prob. 17PCh. 12 - Prob. 18PCh. 12 - Prob. 19PCh. 12 - Prob. 20PCh. 12 - Prob. 21PCh. 12 - Prob. 22PCh. 12 - Prob. 23PCh. 12 - Prob. 24PCh. 12 - Prob. 25PCh. 12 - Prob. 26PCh. 12 - Prob. 27PCh. 12 - Prob. 28PCh. 12 - Prob. 29PCh. 12 - Prob. 30PCh. 12 - Prob. 31PCh. 12 - Prob. 32PCh. 12 - Prob. 33PCh. 12 - Prob. 34PCh. 12 - Prob. 35PCh. 12 - Prob. 36PCh. 12 - Prob. 37PCh. 12 - Prob. 38PCh. 12 - Prob. 39PCh. 12 - Prob. 40PCh. 12 - Prob. 41PCh. 12 - Prob. 42PCh. 12 - Prob. 43PCh. 12 - Prob. 44PCh. 12 - Prob. 45PCh. 12 - Prob. 46PCh. 12 - Prob. 47PCh. 12 - Prob. 48PCh. 12 - Prob. 49PCh. 12 - Prob. 50PCh. 12 - Prob. 51PCh. 12 - Prob. 52PCh. 12 - Prob. 53PCh. 12 - Prob. 54PCh. 12 - Prob. 55PCh. 12 - Prob. 56PCh. 12 - Prob. 57PCh. 12 - Prob. 58PCh. 12 - Prob. 59PCh. 12 - Prob. 60PCh. 12 - Prob. 61PCh. 12 - Prob. 62PCh. 12 - Prob. 63PCh. 12 - Prob. 64PCh. 12 - Prob. 65PCh. 12 - Prob. 66PCh. 12 - Prob. 67PCh. 12 - Prob. 68PCh. 12 - Prob. 69PCh. 12 - Prob. 70PCh. 12 - Prob. 72PCh. 12 - Prob. 73PCh. 12 - Prob. 74PCh. 12 - Prob. 75PCh. 12 - Prob. 76P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A 5.00-kg block is on a level tabletop where the coefficient of kinetic friction between the block and the surface of the table is 0.500. The 5.00- kg block is connected to a vertically-hanging 4.00-kg block via a cable that passes over a 2.00-kg, 5.00-cm radius pulley fastened to the edge of the table. The portion of the cable directly over the surface of the table is also level. (See the diagram below.) What is the linear acceleration of the system? 5.00-kg block 0165 m² Ob-2.65 m/s² OC 194 m/s² Od 354 m/s² Oe-1.47 m/s² 2.00-kg, 5.00-cm radius pulley -4.00-kg blockarrow_forward(a) Calculate the force (in N) the woman in the figure below exerts to do a push-up at constant speed, taking all data to be known to three digits. (You may need to use torque methods from a later chapter.) m = 65 kg CG Freaction 0.86 m 1.44 m (b) How much work (in J) does she do if her center of mass rises 0.260 m? (c) What is her useful power output (in W) if she does 21 push-ups in 1 min? (Should work done lowering her body be included? See the discussion of useful work in Work, Energy, and Power in Humans.) Warrow_forwardA flat belt is used to transmit a couple from pulley to pulley B. The radius of each pulley is 60 mm, and a force of magnitude P = 900 N is applied as shown to the axle of pulley A. Knowing that the coefficient of static friction is 0.35, determine (a) the larg- est couple that can be transmitted, (b) the corresponding maximum value of the tension in the belt. 0000 240 mm BOarrow_forward
- a beam of wood with mass 13 kg is supported at two points. The distances from the center of mass of the bean of wood to the left support point and the right support point are 3.1m and 2.2 m respectively. Find the magnitude of the normal force in th eunit of N at the lef support point if the beam is at equilibrium. Use g=9.8 m/s^2 for the acceleration due to gravity. Answer to nearest tenth if necessary.arrow_forwardwhaT magnitude of (constant) force appliedhorizontally at the axle of thewheel is necessary to raise the wheelover a step obstacle of heighth = 3.00 cm? The wheel’s radius is r =6.00 cm, and its mass is m= 0.800 kg.arrow_forwardA large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 620 kg and an average gear-tooth force of 2.15 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assumer-110 mm, R-615 mm, 0 = 25° Detail of contact at B Answer: mmarrow_forward
- Trina is a gym goer with a leg length of 84 cm. Suppose that she is in the gym doing straight legraising with 10 lb weights. Compute for the force that the muscle should exert in order to (1) maintain it in the position and(2) lift the weight up given that the distance of the effort (muscle) from the joint is 54 cm,distance of the weight is 80 cm, and the COM is 45 cm from the joint. ANSWER THESE QUESTIONS: 1.) Compute for the force that will maintain the position. 2.) Compute for the force needed to lift the weight higher. 3.) Assuming that the hip flexion angle is at 60 degrees, compute for the lineardisplacement of the leg.arrow_forwardA bicycle wheel is at rest against a curb. if the wheel has a radius R, and a mass M and is at rest against a curb of height h=.14R, determine the minimum horizontal force in terms of M and g that must be applied to the axle to make the wheel start to rise up over the steparrow_forward(a) Calculate the force (in N) the woman in the figure below exerts to do a push-up at constant speed, taking all data to be known to three digits. (You may need to use torque methods from a later chapter.) m = 65 kg CG N 0.85 m 1.41 m W reaction (b) How much work (in J) does she do if her center of mass rises 0.260 m? (c) What is her useful power output (in W) if she does 21 push-ups in 1 min? (Should work done lowering her body be included? See the discussion of useful work in Work, Energy, and Power in Humans.) Warrow_forward
- The mine car and its contents have a total mass of 5 kg and a center of gravity at G. If th coefficient of static friction between the wheels and the tracks is 0.3 when the wheels an locked, find the normal force acting on the front wheels at B and the rear wheels at A whe the brakes at both A and B are locked. Does the car move? (g = 9.81 m/s²) 17 N 0.8 m B •G 0.5 m- -1.2 m- 0.1 marrow_forwardThe figure below shows an outstretched arm (0.61 m in length) that is parallel to the floor. The arm is pulling downward against the ring attached to the pulley system, in order to hold the 98 N weight stationary. To pull the arm downward, the latissimus dorsi muscle applies the force M in the figure, at a point that is 0.069 m from the should joint and oriented at an angle of 29°. The arm has a weight of 47 N and a center of gravity (cg) that is located 0.28 m from the shoulder joint. 0.61 m 0.28 m 0.069 m Axis at 98 N shoulder joint cg 29 Aldentify all the forces on the arm and draw an accurate and complete free body diagram on both the arm and the 98 N weight. You may draw on the figure if you wish. B Write down the correct equation of motion ON THE 98 N WEIGHT by summing all the forces acting on it using Newton's 2nd Law of Motion. You must identify and draw your chosen coordinate system. ( Write down the correct equation of motion ON THE ARM by summing all the forces acting on it…arrow_forwardBlock B, in the figure below, weighs 100 kg. The coefficient of friction () between Block B and the floor is 0.4. Pulley A has a radius of gyration (k) of 0.5 m, it has a mass of 300 kg (I-mk-) and a diameter of 15m. The system starts from rest. Neglect the weight of the cable. A constant force (P) of 1000 N is applied. Using the incrtia method of Chapter 13 determine: a) the angular acceleration of Pulley A b) the tension in the cable 100 kg B. 30 300 kg k-0.5m Dia-1.5 marrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- University Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice University
University Physics Volume 1
Physics
ISBN:9781938168277
Author:William Moebs, Samuel J. Ling, Jeff Sanny
Publisher:OpenStax - Rice University
Rotational Kinetic Energy; Author: AK LECTURES;https://www.youtube.com/watch?v=s5P3DGdyimI;License: Standard YouTube License, CC-BY