Vector Mechanics for Engineers: Statics and Dynamics
12th Edition
ISBN: 9781259638091
Author: Ferdinand P. Beer, E. Russell Johnston Jr., David Mazurek, Phillip J. Cornwell, Brian Self
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Question
Chapter 10.1, Problem 10.49P
To determine
Derive the expression for the
Show that the mechanical efficiency cannot exceed 1/2 if the block is to remain in place when the force P is removed.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A block with weight W is pulled up a plane forming an angle a with the horizontal by a force P directed along the plane. μ If is the coefficient of friction between the block and the plane, derive an expression for the mechanical efficiency of the system. Show that the mechanical efficiency cannot exceed 1/2 if the block is to remain in place when the force P is removed.
A 150lb man stands on a 60lb bar to which a cable is fixed at B. The cable passes over two fixed pegs with coefficients of friction indicated. Assume that the arrangement of the pegs permits the cable to contact each peg over a total angle of 90-degrees (90-degrees per peg). Assume that the normal force exerted by the man on the bar acts downward through A. Find the largest force the man can exert on the cable and maintain the bar horizontal.
.A belt 200 mm wide and 7 mm thick drives a pulley at belt speed of 25 m/s. The density of the belt is 980 kg/m3 and the coefficient of friction between the belt and pulley is 0.23. Given that the angle of contact of pulley is 2π/3 and the allowable stress of the belt is 1.8 MPa, determine the tension on the slack side of the belt (T2) in N
Chapter 10 Solutions
Vector Mechanics for Engineers: Statics and Dynamics
Ch. 10.1 - Determine the vertical force P that must be...Ch. 10.1 - Determine the horizontal force P that must be...Ch. 10.1 - Prob. 10.3PCh. 10.1 - Prob. 10.4PCh. 10.1 - Prob. 10.5PCh. 10.1 - A spring of constant 15 kN/m connects points C and...Ch. 10.1 - The two-bar linkage shown is supported by a pin...Ch. 10.1 - Determine the weight W that balances the 10-lb...Ch. 10.1 - Prob. 10.9PCh. 10.1 - Prob. 10.10P
Ch. 10.1 - Solve Prob. 10.10, assuming that the force P...Ch. 10.1 - Prob. 10.12PCh. 10.1 - Prob. 10.13PCh. 10.1 - Prob. 10.14PCh. 10.1 - Prob. 10.15PCh. 10.1 - 10.15 and 10.16 Derive an expression for the...Ch. 10.1 - Prob. 10.17PCh. 10.1 - Prob. 10.18PCh. 10.1 - Prob. 10.19PCh. 10.1 - Prob. 10.20PCh. 10.1 - Prob. 10.21PCh. 10.1 - A couple M with a magnitude of 100 Nm isapplied as...Ch. 10.1 - Rod AB is attached to a block at A that can...Ch. 10.1 - Solve Prob. 10.23, assuming that the 800-N force...Ch. 10.1 - In Prob. 10.9, knowing that a = 42 in., b = 28...Ch. 10.1 - Determine the value of corresponding to...Ch. 10.1 - Prob. 10.27PCh. 10.1 - Determine the value of corresponding to...Ch. 10.1 - Prob. 10.29PCh. 10.1 - Two rods AC and CE are connected by a pin at Cand...Ch. 10.1 - Solve Prob. 10.30 assuming that force P is movedto...Ch. 10.1 - Prob. 10.32PCh. 10.1 - Prob. 10.33PCh. 10.1 - Prob. 10.34PCh. 10.1 - Prob. 10.35PCh. 10.1 - Prob. 10.36PCh. 10.1 - Prob. 10.37PCh. 10.1 - Prob. 10.38PCh. 10.1 - Prob. 10.39PCh. 10.1 - Prob. 10.40PCh. 10.1 - Prob. 10.41PCh. 10.1 - The position of boom ABC is controlled by...Ch. 10.1 - Prob. 10.43PCh. 10.1 - Prob. 10.44PCh. 10.1 - Prob. 10.45PCh. 10.1 - Prob. 10.46PCh. 10.1 - Denoting the coefficient of static friction...Ch. 10.1 - Prob. 10.48PCh. 10.1 - Prob. 10.49PCh. 10.1 - Prob. 10.50PCh. 10.1 - Prob. 10.51PCh. 10.1 - Prob. 10.52PCh. 10.1 - Prob. 10.53PCh. 10.1 - Prob. 10.54PCh. 10.1 - Prob. 10.55PCh. 10.1 - Prob. 10.56PCh. 10.1 - Prob. 10.57PCh. 10.1 - Determine the horizontal movement of joint C if...Ch. 10.2 - Using the method of Sec. 10.2C, solve Prob. 10.29....Ch. 10.2 - Prob. 10.60PCh. 10.2 - Prob. 10.61PCh. 10.2 - Prob. 10.62PCh. 10.2 - Prob. 10.63PCh. 10.2 - Prob. 10.64PCh. 10.2 - Prob. 10.65PCh. 10.2 - Using the method of Sec. 10.2C, solve Prob. 10.38....Ch. 10.2 - Prob. 10.67PCh. 10.2 - Prob. 10.68PCh. 10.2 - Prob. 10.69PCh. 10.2 - Prob. 10.70PCh. 10.2 - Prob. 10.71PCh. 10.2 - Prob. 10.72PCh. 10.2 - Prob. 10.73PCh. 10.2 - Prob. 10.74PCh. 10.2 - A load W of magnitude 144 lb is applied to...Ch. 10.2 - Solve Prob. 10.75, assuming that the spring...Ch. 10.2 - Bar ABC is attached to collars A and B that...Ch. 10.2 - Solve Prob. 10.77, assuming that the spring...Ch. 10.2 - Prob. 10.79PCh. 10.2 - Prob. 10.80PCh. 10.2 - Prob. 10.81PCh. 10.2 - A spring AB of constant k is attached to two...Ch. 10.2 - Prob. 10.83PCh. 10.2 - Prob. 10.84PCh. 10.2 - Prob. 10.85PCh. 10.2 - Prob. 10.86PCh. 10.2 - Prob. 10.87PCh. 10.2 - Prob. 10.88PCh. 10.2 - Prob. 10.89PCh. 10.2 - Prob. 10.90PCh. 10.2 - Prob. 10.91PCh. 10.2 - Prob. 10.92PCh. 10.2 - Prob. 10.93PCh. 10.2 - Prob. 10.94PCh. 10.2 - Prob. 10.95PCh. 10.2 - Prob. 10.96PCh. 10.2 - Bars AB and BC, each with a length l and of...Ch. 10.2 - Solve Prob. 10.97 knowing that l = 30 in. and k =...Ch. 10.2 - Bars AB and CD, each of length l and of negligible...Ch. 10.2 - Solve Prob. 10.99, assuming that the vertical...Ch. 10 - Determine the vertical force P that must be...Ch. 10 - Determine the couple M that must be applied...Ch. 10 - Prob. 10.103RPCh. 10 - Prob. 10.104RPCh. 10 - Prob. 10.105RPCh. 10 - Prob. 10.106RPCh. 10 - Prob. 10.107RPCh. 10 - Prob. 10.108RPCh. 10 - Prob. 10.109RPCh. 10 - Prob. 10.110RPCh. 10 - Prob. 10.111RPCh. 10 - Prob. 10.112RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.arrow_forwardA 20 kg block is held in place on an incline plane as shown by a rope that passesover a frictionless pulley at B and then over a fixed cylinder at C where thecoefficient between the rope and the fixed cylinder is 0.2. Given an angle ofincline, A = 25°, if a force of P = 200 V is applied to the end of the rope,(a) Will the block move if the coefficient of static friction between the block and theinclined surface is M, = 0.56?(b)If impending motion exists, will the block tip or slip?arrow_forwardA 20 kg block is held in place on an incline plane as shown by a rope that passes over a frictionless pulley at B and then over a fixed cylinder at C where the coefficient between the rope and the fixed cylinder is 0.2. Given an angle of incline, 0 = 25°, if a force of P = 200 N is applied to the end of the rope, (a) Will the block move if the coefficient of static friction between the block and the inclined surface is μ = 0.56? (b)lf impending motion exists, will the block tip or slip? Enter the magnitude of force in the rope that will cause tipping of the block as the answer in the Respondus answer-box. 0.4 m 0.8 m Ө MA 0.5 m C B Parrow_forward
- A 20 kg block is held in place on an incline plane as shown by a rope that passes over a frictionless pulley at B and then over a fixed cylinder at C where the coefficient between the rope and the fixed cylinder is 0.2. Given an angle of incline, 0 = 25°, if a force of P = 200 N is applied to the end of the rope, (a) Will the block move if the coefficient of static friction between the block and the inclined surface is μ = 0.56? (b)lf impending motion exists, will the block tip or slip? Enter the magnitude of force in the rope that will cause tipping of the block as the answer in the Respondus answer-box. 0.4 m 0.8 m MA 0.5 m C B Parrow_forwardA 400-N cabinet is being pushed by a man on a concrete floor with a coefficient ofstatic friction of 0.37 and a coefficient of kinetic friction of 0.12. He exerts a force, F, of100 N at an angle of θ = 20° on the cabinet.Determine:i. The normal force, N (draw the FBD)ii. The characteristic of friction or the state of motion (static or kinetic)iii. The value of the actual friction force, Ff (show the equations of equilibrium)iv. The value of F if the motion is impending (show the equations of equilibrium)arrow_forwardA block with mass of m, = 2 kg is placed on top of a block with a mass m2 = 4 kg. A horizontal force of F=60 N is applied to the block m2, and the block m, is tied to the wall. The coefficient of kinetic friction between all surfaces is 0.400. (a) Draw a free-body diagram for each block and identify the action-reaction forces between the blocks. (b) Determine the tension in the string and the magnitude of the acceleration of the block m2.arrow_forward
- 2. The 100 – Ib force acts as shown on a 300 - Ib block placed on an inclined plane. The coefficients of friction between the block and the plane are us = 0.25 and Hk = 0.20. Determine whether the block is in equilibrium, and find the value of the friction for the friction force. 300 Ib 100 lbarrow_forwardA flat belt connects pulley a, which drives a machine tool, to pulley b, which is attached to the shaft of an electric motor. the coefficients of friction are μs = 0.25 and μk = 0.20 between both pulleys and the belt. knowing that the maximum allowable tension in the belt is 600 lb, determine the largest torque that the belt can exert on pulley aarrow_forwardA 60-kg cabinet is mounted on casters that can be locked to prevent their rotation. The coefficient of static friction between the floor and each caster is 0.35. 1. If h = 600 mm, determine the magnitude of the force P (in N) required to move the cabinet to theright, if all the casters are locked. (ANSWER: 206) 2. If h = 600 mm, determine the magnitude of the force P (in N) required to move the cabinet to the right if the casters at B are locked and the casters at A are free to rotate. (ANSWER: 178)arrow_forward
- • Draw a free body diagram of the box on the incline. . Determine the weight (W) of the box on the incline surface. Determine the normal force (N) acting on the inclined box. Determine the friction force (F) acting on the inclined box. ● 7. A box of unknown weight is being pulled on a = 39 degree inclined surface by a frictionless pully system attached to a 540 pound box hanging off the pully. The coefficient of static friction between the box and the inclined surface is μ = 0.33 and both boxes are not moving. Answer the questions below: ● W= N = Ff= 0 W lbs lbs lbs 540 lbsarrow_forwardA block with mass of m, = 2 kg is placed on top of a block with a mass m2 = 4 kg. A horizontal force of F=60 N is applied to the block m2, and the block m, is tied to the wall. The m1 coefficient of kinetic friction between all surfaces is F 0.400. (a) Draw a free-body diagram for each block and identify the action-reaction forces between the blocks. (b) Determine the tension in the string and the magnitude of the acceleration of the block m2 m2.arrow_forwardA 60-kg cabinet is mounted on casters that can be locked to prevent their rotation. The coefficient of static friction between the floor and each caster is 0.35. 3. If h = 600 mm, determine the magnitude of the force P (in N) required to move the cabinet to the right if the casters at A are locked and the casters at B are free to rotate. (ANSWER: 72.5)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
How to balance a see saw using moments example problem; Author: Engineer4Free;https://www.youtube.com/watch?v=d7tX37j-iHU;License: Standard Youtube License