Which of the following ratings (PIV- Peak Inverse Voltage and temperature) is true? Si diodes have lower PIV and narrower temperature ranges than Ge diodes. O Si diodes have lower PIV and wider temperature ranges than Ge diodes. Si diodes have higher PIV and narrower temperature ranges than Ge diodes. O Si diodes have higher PIV and wider temperature ranges than Ge diodes. To increase the electrical conductivity of an intrinsic semiconductor, we need to O add impurity increase the resistivity apply heat None of the them

Which of the following ratings (PIV- Peak Inverse Voltage and temperature) is true? Si diodes have lower PIV and narrower temperature ranges than Ge diodes. O Si diodes have lower PIV and wider temperature ranges than Ge diodes. Si diodes have higher PIV and narrower temperature ranges than Ge diodes. O Si diodes have higher PIV and wider temperature ranges than Ge diodes. To increase the electrical conductivity of an intrinsic semiconductor, we need to O add impurity increase the resistivity apply heat None of the them

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
a) What is n-type semiconductor materials? What are the majority and the minority cariers? b) What is p-type semiconductor materials? What are the majority and the minority cariers? c) What is depletion region of a p-n junction diode? d) Describe in your own words the forward-bias and reverse- bias conditions of a p-n junction diode. e) Draw a Diode Symbol and label the anode and the cathode. Si Ge 2 ka f) Find V, in the circuit shown in +20 V 2 k2 15V Fig. Fuad Al-Mannai EENG261 Page 1
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
Calculate the currents passing through the diodes D1 and D4 in the circuit given below. (All diodes are silicon).
How many valence electrons does a semiconductor has? a. 2 b. 3 c. 6 d. 4 When pure semiconductor is heated, its conductance a. Goes up b. Goes down C. Remains the same d. Can't say When a trivalent impurity is added to a pure semiconductor, it becomes a. A conductor b. An intrinsic semiconductor C. P-type semiconductor d. N-type semiconductor
A diode circuit is given in the below figure, in which two diodes are connected in series and their saturation currents are Is1 =10-¹6 A and Is2 =10-¹4 A. If the applied source voltage is 1 V, calculate the currents IDI and ID2 and the voltage across each diode VDI and VD2. IDI Ī Vpl + D₂ VD2
For the circuit shown in the Figure, if the diodes are silicon diodes with VD(on)=0.7 V, and VIn=50 sin wt V, V1 =7 V and V2 =13 V, then the value of VOUT (p-p) is: R1 D, D2 VIN VOUT vi E v2= Ca. 19.4 V Ob. 17.4 V Cc. 15.4 V Cd. 21.4 V
All pn diodes shown below have a voltage drop of 0.3 V when they are "ON". +4V DIA 5k2 D2 VOUT VA 5k2 V8 D1B -2V Indicate in the table whether the diodes D1A, D1B and D2 are ON/OFF with the given VA and VB values. Also give the corresponding VOUT numerical values. DIA (ON/OFF) DiB(ON/OFF) Dz(ON/OFF) VoUT (sign and numerical value) VA |V8 OV +4V OV +3V ov +4V
C. In the circuit shown below the knee current for the ideal Zener diode is 10 mA Calculate the minimum value of load resistance RL in order to maintain 5 volts across the load resistance RL 2. WW-
points) For the circuit shown below, sketch to scale the output V, waveform and draw the transfer characteristic (V. versus Vi), Assume the diodes are ideal. V₁ =15-sin wt Zloks www loks # HIF 4V + Vo
Draw the characteristics of Ideal and practical diodes. A semiconductor has electron and hole mobilities as Hn = 7500 cm³ /V. sec, Hp = n = 3.6 x 1012 cm-3. Find (i) The hole concentration when conductivity is minimum. (ii) The minimum conductivity. 300 cm /V.sec and
Q2:- Find the level of Vo for each circuit shown in the Figure below. Also, determine the status of each diode; if it is forward or reverses biasing. Assume all diodes are silicone with 0.7v drop. +5 V +15 V -10 V (12 Marks) R DI +5 VoK D +5 VoK DI -5 VoH -5 Vo4 D2 D2 D2 +5 VoH D3 +5 Vo4 D3 -10 VoK D4 V. -5 Vo K (a) (b)