A 1N4748A zener diode has a ZZ of 23 Ω. Taking the data from the datasheet VZ = 22 V with a test current, IZ, of 11.5 mA. What is the voltage across the zener terminals when the current is 6 mA? When the current is 20 mA? Make the representation of the values by means of their curve characteristic.

A 1N4748A zener diode has a ZZ of 23 Ω. Taking the data from the datasheet VZ = 22 V with a test current, IZ, of 11.5 mA. What is the voltage across the zener terminals when the current is 6 mA? When the current is 20 mA? Make the representation of the values by means of their curve characteristic.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 3RQ: Diodes and rectifiers allow current to _________. flow in one direction only flow in both...

See similar textbooks

Similar questions

Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
What is the difference between a diode and rectifier?
Given the following circuit with VDD= 9.2 V, R=2.3 k2, then the current Iis: Use the CVD model for the diode, with VD = 0.65 V. I VDD a. 0.004000 A O b. 3.717391 A OC. 0 A d. 4.000000 A e. 0.003717 A R + VD -
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A RL VL-DC =20V 220V omsb O 001 F O 0.02 F O 0.0167F O None of the above Activate
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
Assuming an ideal diode model for all the diodes in the circuit below, chose the correct state (bias) for each diode. R1 ww 9kQ 1N1199C R2 D1 18kQ 1N1199C V2 12 V R3 1kQ D3 1N1199C R4 D3: On (Forward Bais) D3: Off (Reverse Bais)
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
A zener diode exhibits a certain change in VZ for a certain change in IZ on a portion of the linear characteristic curve between IZK and IZM as illustrated in Figure 5. Calculate the zener impedance.
I ln. l. . :D docs.google.com/forms/d/e/1l Diode clippers are wave-shaping circuits in that they are not used to prevent signal voltage from going above or below certain * .levels TO F like that of the clipper, the shape of the .input signals of a clamper is changed F The clamping circuit clamps or shift the * .input sinusoidal signal up or down FO II
Q4) Determine and sketch the output voltage across the load resistor (RL) for the circuit shown below. (assume Si diodes) V_DC 0.75 0.25 V_SIN Y SIN as RL -1 v SOR V_SQR 0.75 -0.75 V_TRI V TRI as
Determine which diodes are forward-biased and which are reverse-biased in the configurations shown in Figure 4. Assuming a 0.7-V drop across each forward-biased diode, determine the output voltage. O+5 V -10 V R DI +s vOK D, -SVOKH D3 +s vOK D4 -5 voK DI -5VOK Dz OVout OVout +5 voK Figure 4.
In the Figure as shown below the current (I) will be equal to: ---- Assume that all diodes are silicon -practical diode model 4 KUZ lovt 32 KSL 2.2 mA O 2.3 mA O 2.4 mA O 1.1 mA O