Which among the following is a key process adopted for the laser beam formation as it undergoes the light amplification? А. spontaneous Emission, В. stimulated Emission, С. both A and B, D. none of the above. In Stimulated Emission, which among the following parameters of generated photon is/are similar to the photon of incident wave? A. phase, B. frequency, C. polarization & direction of travel, D. all of the above. In a LASER structure, the existence of standing waves is possible at frequencies for which the distance between the mirrors is an integral number of . А. 2/2, В. 2/4, С. 2/6, D. 2/8. In a full wave rectifier, if the input frequency is 50 Hz, then output frequency will be A. 50 Hz, В. 75 Hz, C. 100 Hz, D. 200 Hz. In a bridge type full wave rectifier, if Vm is the peak voltage across the secondary of the transformer, the maximum voltage coming across each reverse biased diode is A. Vm, В. 2 Vm. C. Vm/2, D. Vm/V2. A circuit that removes positive or negative parts of waveform is called A. clamper, B. clipper, C. diode clamp, D. limiter.

Which among the following is a key process adopted for the laser beam formation as it undergoes the light amplification? А. spontaneous Emission, В. stimulated Emission, С. both A and B, D. none of the above. In Stimulated Emission, which among the following parameters of generated photon is/are similar to the photon of incident wave? A. phase, B. frequency, C. polarization & direction of travel, D. all of the above. In a LASER structure, the existence of standing waves is possible at frequencies for which the distance between the mirrors is an integral number of . А. 2/2, В. 2/4, С. 2/6, D. 2/8. In a full wave rectifier, if the input frequency is 50 Hz, then output frequency will be A. 50 Hz, В. 75 Hz, C. 100 Hz, D. 200 Hz. In a bridge type full wave rectifier, if Vm is the peak voltage across the secondary of the transformer, the maximum voltage coming across each reverse biased diode is A. Vm, В. 2 Vm. C. Vm/2, D. Vm/V2. A circuit that removes positive or negative parts of waveform is called A. clamper, B. clipper, C. diode clamp, D. limiter.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the diagram of a halfwave power supply circuit and a full wave supply circuit. Aside from the difference between the number of diodes utilized in both circuits, state the main advantage of the full wave power against the halfwave circuit for the following scenario . When there is a defective diode (open anode- cathode ) When the filter capacitor is defective (capacitor is open)
Explain stimulated emission in a lasing media. Simply assume that the lasing media has only 2 energy levels.
4 (a) “There are three types of optical fibers available for optic communication”. What are these three types and describe each. You may use diagrams to help you with your answers. (b) Pin diodes and Avalanche photodiodes (APD) are detectors which are used to convert the transmitted light back into an electrical signal I. Describe the operating principles of a PIN diode and an Avalanche photodiode II. The quantum efficiency of APD is 80% for the detection of radiation at a wavelength of 0.9 μm. When the incident optical power is 0.5 μW, the output current from the device (after avalanche gain) is 11 μA. Determine the multiplication factor of the photodiode under these conditions. (c) A silica optical fibre with a core diameter large enough to be considered by ray theory analysis has a core refractive index of 1.480 and a cladding refractive index of 1.44. Determine: I. The critical angle at the core–cladding interface II. The acceptance angle in air for the fibre.
Q2//Answer Any Two 1. State the applications of Clamper.2- What are the disadvantages of LED? 3- Why Si & Ge are not used in LED? Q3/ Write in brief on Avalanche diode. Q4/Does Clamper circuit change the peak-to-peak (l.e., rms value)? Justfy Q5/ State the applications of the photodiode.
10. The is a two-terminal semiconductor device whose terminal resistance will vary ........... (linearly) with the intensity of the incident light. 11. There are four modes of Triac operation, depending on
5) An LED light is powered by a 20V DC (low:0V to high:20V) square wave source in frequency of 1.2KHZ. Find the power delivered (average) to the LED light when the square wave is in 30%, 50%, and 80% duty-cycle respectively.
a. Why high energy electron beam (instead of visible light) is used in microscope to increase its resolution? b. In optical fiber communication, why wavelengths ~ 1310 nm and 1550 nm are often preferred? c. What are the conditions for laser oscillation?
What is the action of a capacitor in a Power Supply Circuit?* a. To de-couple DC component of the rectified AC input b. To increase the DC component of the output wave. c. To remove DC component of the AC wave. d. None of the above.
a) (i) Draw the electrical model of a piezoelectric crystal. (ii) Over what portionof the reactance curve do we desire oscillations to take place when the crystal isused as part of a sinusoidal oscillator? Explain. b) An N-channel JFET has IDSS = 16 mA and VP= -6 volts. Calculate the draincurrent and VDS (sat) when VGS = -4 volts.
The waveform given below is observed on the screen of a CRO. If the time/div switch is set at 10 µsec and the volt/div at 200 mV, the frequency and peak to peak voltage are, respectively. -1.5 -1 -1- -2- 2 1 1 1.5 2
6. What do you understand by Ferranti effect?
derive forirer components of square wave signal