What is the threshold torsion (kN-m) of a rectangular beam with a width of 410 mm and an over-all depth of 573 mm? The distance of the tension reinforcements from the bottom fiber of the beam is 67 mm. The specified compressive strength of concrete is 27.00 MPa. The yield strength of tension reinforcements and stirrups are 402 MPa and 325 MPa respectively.

What is the threshold torsion (kN-m) of a rectangular beam with a width of 410 mm and an over-all depth of 573 mm? The distance of the tension reinforcements from the bottom fiber of the beam is 67 mm. The specified compressive strength of concrete is 27.00 MPa. The yield strength of tension reinforcements and stirrups are 402 MPa and 325 MPa respectively.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Similar questions

The following data of a pre-stress concrete are given: Beam dimension ; bxh = 300 mm x 600 mm Loads Super imposed dead load 7 KN/m Live load = 20 KN/m Unit Weight of concrete 23 KN/cubic meter The beam is simply supported on a span of 15 meters and are pre tensioned with total initialpre tensioned with total initial force of 1750 KN from low-relaxation strand with centroid 220 mm below neutral axis throughout the beam length .There is a 15% loss of stress at service loads. The concrete covering of the pre-stressed concrete is _____mm., the total dead load is _____ KN/m.
2. Tensile strength of concrete is about: (20-35)% of compressive strength (45-70)% of compressive strength None of the above. Tension controlled section Balanced section Compression-controlled section 4- The reduction factor (0) is equal to 0.9 if the: Es 2 Ety + 0.003 Es S Ety + 0.003 Es Ety 5- The design method which use the factored loads is - Working stress method - Ultimate design Method - None of above 6- If p< Po therefore the section is - Under reinforced - Over reinforced - None of above
SIT. B: Determine the tensile steel ratio of a given conditions if concrete strength f'. = 28 MPa and steel yield strength fy 4. if the tensile strain is Es = fy/Es upon crushing of concrete at a strain of 0.003. C. 0.02833 A. 0.01567 B. 0.02161 D. 0.02125 if the tensile strain is limited to 0.004 upon crushing of concrete at a strain of 0.003. A. 0.01567 B. 0.01548 5. 6. Minimum as required by NSCP 2015. C. 0.00313 D. 0.00405 A. 0.00333 B. 0.00276 = 420 MPa. C. 0.02778 D. 0.02064 uniformly
9. If the value of the fc' of concrete is 30 MPa, and the actual stress of the concrete subjected to a force is 12 MPa, at what stage is the concrete at?
If the compressive strength of the concrete is 4 ksi and the yield strength of steel is 60 ksi, the value of that should be used in computing the design moment strength oMn for the beam section should be 23.5 in 1.5424 0.65 0.48 0.9 3#9 14 in 26 in
The concrete in the core of a spiral column is sub- jected to a uniform confining stress o, of 680 psi. What will the compressive strength o be? The un- confined uniaxial compressive strength is 5000 psi.
A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive bending moment of 78 kip, in psi (neglect steel reinforcement) B. If fc= 3200 psi and normal weight of concrete is used, does cracking occurs? What is the maximum uniformly distributed load the beam can carry if it is used as a simple beam with a 26 ft span without exceeding the modulus of rupture of the concrete, in lb/ft? 250 mm 80 mm 130 mm 80 mm 80 mm
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars. Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPA. 640 mm 800 mm 6 #32 C 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
Assuming the concrete is uncracked, compute the flexure stresses in the extreme fibers of the beam as shown in the figure for a bending moment of 34 kN-m. The concrete has an f' of 27.60 MPa; determine also the cracking moment of the section. (Use 0.62 1 = 0.70 in calculating the modulus of rupture). Dimensions are in millimeter. 380 455 3 #9 bars (A, = 3.00 in.2) 75 300
The flexural tensile strength of M25 grade of concrete, in N/mm², as per IS:456-2000 is A 0.5 B 5 C 2.25 D 3.5
A pre stressed concrete beam has a width of 200 mm and an overall depth of 400 mm. The permissible stresses in tension and compression due to pre- stressing alone are 4 N/mm and 25 N/mm respectively. Find the required pre- stressing force in the tendon and the eccentricity of the tendon, if a straight tendon with a constant eccentricity is to be provided in the beam. No external load or self weight effect is to be considered.
Item 5 Column AB is made from high strength pre-cast concrete and reinforced with four in diameter A-36 steel rods. The allowable normal stress for the high strength concrete and the steel are (allow) con = 2.6 ksi and (allow) st = 24 ksi, respectively. The modulus of elasticity for high strength concrete is 4.2 x 10³ ksi and for A-36 steel is 29 x 10³ ksi. (Figure 1) Figure 1 ▾of 1 10 ft a P B9 in. 9 in. Section a-a Part A Determine the magnitude of the maximum allowable floor loading P. Express your answer to three significant figures and include the appropriate units. μA Pmax= 158.91 kips Submit My Answers Give Up Incorrect; Try Again; 2 attempts remaining ? Provide Feedback Continue