A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive bending moment of 78 kip, in psi (neglect steel reinforcement) B. If f'c= 3200 psi and normal weight of concrete is used, does cracking occurs? What is the maximum uniformly distributed load the beam can carry if it is used as a simple beam with a 26 ft span without exceeding the modulus of rupture of the concrete, in lb/ft? 250 mm 80 mm 130 mm 80 mm 80 mm

A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive bending moment of 78 kip, in psi (neglect steel reinforcement) B. If f'c= 3200 psi and normal weight of concrete is used, does cracking occurs? What is the maximum uniformly distributed load the beam can carry if it is used as a simple beam with a 26 ft span without exceeding the modulus of rupture of the concrete, in lb/ft? 250 mm 80 mm 130 mm 80 mm 80 mm

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Similar questions

The grade of the concrete is M25. Find the values of design strength in- 1. Direct Compression. 2. Bending Compression & 3. Flexural Tension.
2. Tensile strength of concrete is about: (20-35)% of compressive strength (45-70)% of compressive strength None of the above. Tension controlled section Balanced section Compression-controlled section 4- The reduction factor (0) is equal to 0.9 if the: Es 2 Ety + 0.003 Es S Ety + 0.003 Es Ety 5- The design method which use the factored loads is - Working stress method - Ultimate design Method - None of above 6- If p< Po therefore the section is - Under reinforced - Over reinforced - None of above
If the compressive strength of the concrete is 4 ksi and the yield strength of steel is 60 ksi, the value of that should be used in computing the design moment strength oMn for the beam section should be 23.5 in 1.5424 0.65 0.48 0.9 3#9 14 in 26 in
The following data of a pre-stress concrete are given: Beam dimension ; bxh = 300 mm x 600 mm Loads Super imposed dead load 7 KN/m Live load = 20 KN/m Unit Weight of concrete 23 KN/cubic meter The beam is simply supported on a span of 15 meters and are pre tensioned with total initialpre tensioned with total initial force of 1750 KN from low-relaxation strand with centroid 220 mm below neutral axis throughout the beam length .There is a 15% loss of stress at service loads. The concrete covering of the pre-stressed concrete is _____mm., the total dead load is _____ KN/m.
Item 5 Column AB is made from high strength pre-cast concrete and reinforced with four in diameter A-36 steel rods. The allowable normal stress for the high strength concrete and the steel are (allow) con = 2.6 ksi and (allow) st = 24 ksi, respectively. The modulus of elasticity for high strength concrete is 4.2 x 10³ ksi and for A-36 steel is 29 x 10³ ksi. (Figure 1) Figure 1 ▾of 1 10 ft a P B9 in. 9 in. Section a-a Part A Determine the magnitude of the maximum allowable floor loading P. Express your answer to three significant figures and include the appropriate units. μA Pmax= 158.91 kips Submit My Answers Give Up Incorrect; Try Again; 2 attempts remaining ? Provide Feedback Continue
CASE:A rectangular beam has the dimensions (see Fig.1) b = 15 in.,h = 30 in., and d = 27.37 in. and is reinforced with three No.9 bars. The concrete compressive strength fc' is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel fy is 60,000 psi, the stress-strain curves of the materials being those of Fig.2. Determine the stresses caused by a bending moment M = 45 ft-kips.Question1:Check this case, would the concrete of the beam crack? Please calculate the strengths of those two materials in this beam.Question2:Suppose the beam under this case is subject to a bending moment M = 110 ft-kips (rather than45ft-kips as previously). Calculate the relevant properties and stresses.Question3:Determine the nominal moment Mn at which the beam of this case will fail. Question4:Have a comparison of the calculation results with those of three questions.
The permissible bending compressive strength for M 25 grade of concrete is 8.5 N/mm². Its short-term and long-term modular ratios are, nearly
a. A split-tension test was conducted on a concrete cylinder with a 150 mm diameter and 300 mm length. Theload that split the cylinder is 268.5 KN. Calculate the splitting tensile strength (fct) of the concrete. b.The third-point flexural strength test was conducted on a flexural beam of 150 mm by 150 mm cross sectionand 450mm span. The maximum load at failure was 29.2 KN. Calculate the flexural strength of the conc c. The ultimate tensile strength of geogrid is 270 KN/m, and the combined reduction factor for reinforcementapplication is 3.0. Determine the allowable tensile strength. d.A compacted sample of Asphalt cement contains 5.3% asphalt binder by weight of total mix, and its bulkspecific gravity is 2.428. The theoretical maximum specific gravity of the mix is 2.592, and the bulk specificgravity of the aggregate is 2.703. Determine the VMA, VTM and VFA of the Asphalt Ce
The concrete in the core of a spiral column is sub- jected to a uniform confining stress o, of 680 psi. What will the compressive strength o be? The un- confined uniaxial compressive strength is 5000 psi.
A certain concrete beam has the following data: Cracked Moment of Inertia, I¬cr = 7,800 x 10^6 mm^4 Grossed Moment of Inertia, Ig = 9,000 x 10^6 mm^4 Applied Moment, Ma = 80 kN-m Cracking Moment, Mcr = 100 kN-m 28. Determine the effective moment of inertia.
What is the threshold torsion (kN-m) of a rectangular beam with a width of 446 mm and an over-all depth of 536 mm? The distance of the tension reinforcements from the bottom fiber of the beam is 75 mm. The specified compressive strength of concrete is 22.00 MPa. The yield strength of tension reinforcements and stirrups are 404 MPa and 323 MPa respectively.
Assuming the concrete is uncracked, compute the flexure stresses in the extreme fibers of the beam as shown in the figure for a bending moment of 34 kN-m. The concrete has an f' of 27.60 MPa; determine also the cracking moment of the section. (Use 0.62 1 = 0.70 in calculating the modulus of rupture). Dimensions are in millimeter. 380 455 3 #9 bars (A, = 3.00 in.2) 75 300