We want to design a combinational circuit that has two 4-bit inputs A (A,A,A,A,) and B (B,B,B,B,) and one- 1-bit output namely S. The circuit behaves as follows: S=1, if B is none negative and A=+2 S=0, otherwise. Assuming that two's complement is the technique that will be emplyed to represent numbers, find the boolean expression of S. Select one: B,.B, B,'B,'.A, O B,'A,A, A,A O None of the above O B, A, A, A,A, O B,B, B, B, A,' O B, A,'A, A,'A, O B,'A, A, A, A,

We want to design a combinational circuit that has two 4-bit inputs A (A,A,A,A,) and B (B,B,B,B,) and one- 1-bit output namely S. The circuit behaves as follows: S=1, if B is none negative and A=+2 S=0, otherwise. Assuming that two's complement is the technique that will be emplyed to represent numbers, find the boolean expression of S. Select one: B,.B, B,'B,'.A, O B,'A,A, A,A O None of the above O B, A, A, A,A, O B,B, B, B, A,' O B, A,'A, A,'A, O B,'A, A, A, A,

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2. You are to design a circuit that takes a 4-bit number as input (A3, A2, A,, A,) and generates an output which is 1 if the input number is one of the Fibonacci numbers between 2 and 15 and 0 otherwise. You may assume that the input is never 0 or 1. The most significant bit of the input is A,. Please use the Karnaugh map below for this problem. A1A0 A3A2 The Fibonacci numbers are 0, 1, 1, 2, 3, 5, 8, 13, 21, . . .. a) Write this function as a list of minterms (Em(...) notation). Indicate don't cares if you have any. b) Simplify the function using the Karnaugh map. c) Draw a circuit diagram for the minimized function using only AND, OR, and NOT gates.
3. The following figure shows the four-bit Adder-Subtractor. Your inputs for this combinational circuit are A = 8, B = 5 and M = 1. What is the outputs S3, S2, S1, and S0? You have to show how to get the outputs by indicating each carry bit. (Note: You should show all the steps to receive full credits)
The inputs to a digital circuit are having the signals of A, B and C has +5V power supply (logic 1) and the ground (logic 0) are available. The output of the circuit is X-A'B+A'B'C' [a) Write down the output function(X) in its canonical SOP and POS forms (b) Implement the circuit of output function(X) using only two 2:1 multiplexers.
Design a circuit with 3 inputs and 3 outputs, when the binary input is m0, m1, m2 and m3 the output is input plus two and when the input is m4, m5, m6 and m7 then the output is three less then input use k-Map to get the simplified circuit.
The circuit shown below is a 4-bit adder subtractor. The circuit subtracts by doing 2's complement arithmetic, where we take the 2's complement of the number being subtracted. The 2's complement process consists of 2 steps. Explain how the circuit shown below 1. Takes the complement of the number being subtracted; and 2. Adds 1 to the complement.
DESIGN OF COMBINATIONAL CIRCUIT USING LOGISIM You are to design a 4-bit arithmetic unit that consists of a 4-bit adder/subtractor circuit. The arithmetic unit takes as inputs two 4-bit numbers (A and B) and one control input (M) add/subtract selector that selects the type of operation the unit will perform. When the input control is ‘0’, the input numbers are added. When it is set to ‘1’, the two input numbers are subtracted (A - B).
Design a combinational circuit that has 4-inputs (W,X,Y,Z) and 4-outputs (A,B.C,D). If the decimal of binary input is an even number, the binary output is half the decimal input. If the decimal of binary input is an odd number, the binary output is twice of the decimal input .In both cases the output should be less than 16. (don't care when the output is greater than (15)10).
Design a combinational circuit that adds one to a 4-bit binary number. For example, if the input of the circuit is 1101, the output is 1110. The circuit can be designed using four half-adders.
4-11 Design a 4-bit combinational eircuit incrementer. (A circuit that adds one to a 4-bit binary number.) The circuit can be designed using four ralf-adders.
5. The following figure shows the eight-bit Adder-Subtractor. Your inputs for this combinational circuit are A=16, B=31 and M = 1. What are the outputs S7, S6, S5, S4, S3, S2, S1, and S0? Express the outputs with a hexadecimal number. You have to show how to get the outputs by indicating each carry bit. (Note: You should show all the steps)
Use contraction beginning with a 4-bit adder with carry out to design a 4-bit increment-by-3 circuit with carry out that adds the binary value 0011 to its 4-bit input. The function to be implemented is S = A + 0011
Paragraph Styles Determine the output of the DAC in figure A, if the sequence of 4-bit numbers in figure B is applied to the inputs. The data inputs have a low value of OV and a high value of +5V. 200 kf 10 kf) 100 kl 50 kf D, 25kf) D, W. Student arnswer