Two steel springs arranged in series support a load, F. The upper spring has 12 turns of 25 mm diameter wire on a mean diameter of 200 mm. The lower spring consists of 10 active coils of 20 mm diameter wire with a mean diameter of 150 mm. If the maximum shearing stress in either spring must not exceed 220 MPa, determine the maximum value of F. Use G=83GPA. Select one: O a. 3849.35 N O b. 8723.75 N O c. 5700.60 N O d. 4444.35 N

Two steel springs arranged in series support a load, F. The upper spring has 12 turns of 25 mm diameter wire on a mean diameter of 200 mm. The lower spring consists of 10 active coils of 20 mm diameter wire with a mean diameter of 150 mm. If the maximum shearing stress in either spring must not exceed 220 MPa, determine the maximum value of F. Use G=83GPA. Select one: O a. 3849.35 N O b. 8723.75 N O c. 5700.60 N O d. 4444.35 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The helical compression spring is made of 12mm wire diameter with 132 mm mean diameter. Determine stiffness of the spring when modulus of rigidity G=80 kN/mm2,number of turn is 13 and axial load is 190N. Select one: O a. 12N/mm O b. 4.5N/mm O c. 9.5N/mm O d. 17N/mm
The 500 N load is acting on the helical compression spring with 20 number of turns. The helical spring is having the mean diameter of 12cm,spring wire diameter is 6mm. Find the spring inside diameter. Select one: O a. 114 mm O b. 52mm O c. 150mm O d. 20mm
Given a spring with 2.032 mm wire diameter, oil tempered, 8 active coils, OD is 8.5 mm. Determine the free length if the stress will not exceed 820 MPa when spring is compressed solid. Use G = 83 MPa and assume the springs has plain ends. a. 51.6 mm b. 41.6 mm c. 31.6 mm d. 21.6 mm
The inner spring of a compound helical spring is arranged within and concentric with the outer one and is shorter by 9 mm. The outer spring has 10 coils with a mean diameter of 24 mm and a wire diameter of 3 mm. (a) Determine the stiffness of the inner spring when an axial load of 162 N causes the outer spring to compress by 16 mm. If the radial clearance between the springs is 1.5 mm and the inner spring has 8 coils, find its wire diameter. (c) Disregarding the effect of curvature, find the maximum shear stress in each of the spring. Given G = 78 GPa.
The load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches. Rigidity modulus is 11 x 106 psi and the maximum intensity of safe torsional stress is 60,000 psi. If the wire diameter and the mean diameter are 0.5 in. and 3 in., respectively. Determine the number of active coils. Don't round your answer to preferred size. Round your answer to 4 significant figures
The specifications for a coil spring are known. Infinite fatigue life is required, using a safety factor of 1.3 applied to the maximum load only. The fatigue strength can be represented by a line between τmax= 600, τmin= 0 and τmax= τmin= 900 MPa.Assume both end plates are in contact with nearly a full turn of wireand that the end plate loads coincide with the spring axis.Determine a suitable combination of d, D, and N, if C = 8
Fatigue Failure Resulting from Variable Loading 51. A schematic of a clutch-testing machine is shown. The steel shaft rotates at a constant speed w. An axial load 1.170P is applied to the shaft and is cycled from zero to 1.170 P torque T' induced by the clutch face onto the shaft is given by f(1.xxxP)(D+d) T = 4 Where D and d are defined in the figure and f is the coefficient of friction of the clutch face. The shaft is machined with Sy = 800 MPa and Su = 1000 MPa. The theoretical stress- concentration factors for the fillet are 3.0 and 1.8 for the axial and torsional loading, respectively. Assume the load variation P is synchronous with shaft rotation. With f = 0.3, find the maximum allowable load P such that the shaft will survive a minimum of 10° cycles with a factor of safety of 3. Use the modified Goodman criterion. Determined the corresponding factor of safety guarding against yielding. Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display. R…
4. Determine the maximum stress and elongation in a helical steel spring composed of 20 turns of 20 mm diameter wire on a mean radius of 80 mm when the heavy spring is supporting a load of 2 kN. a. Identify and write down the required factor to differentiate spring that considers spring curvature. b. Set up the equations of stress and elongation that is required to solve the problem. c. Solve for the unknown variables by substituting the given in the equations of stress that has been set up previously.
A helical compression spring has a scale of 400 lbs/inch, an inside diameter of 2.5 inches, a free length of 8 inches and with squared and ground ends. Material is to be chrome vanadium steel. For a load P of 750 lbs and for the average service Determine the standard size wire diameter Determine the number of active coils Determine the solid height Determine the stress at solid height
Two concentric, helical compression springs support a 6.5-kip load. The larger spring has an outside diameter of 7 in., a free length of 7 1/8 in., 4 turns, and is made of a 1 3⁄8 in. steel wire. The smaller spring has an outside diameter of 4 1⁄8 in., a free length of 6 13/16 in., 6 turns, and is made of 7⁄8 in. steel wire. Compute the shearing stress in each spring. PLEASE I NEED IT . ASAP
The smaller of two concentric helical spring is made of 22mm diameter steel spring and has an outside diameter of 100 mm with 10 active coils. The outer spring is made of 32mm steel spring and has an outer diameter of 250mm with 8 active coils. Before the load is applied, the outer spring is 25 mm longer than the inner spring. If the load of 90 kN is applied to this nest of springs: a. Determine the spring index of the inner and outer spring b. Determine the spring rate of inner and outer spring C. What load of the inner and outer spring in kN d. Determine the portion of load carried by inner and outer spring.
3. As shown, a 50-kg rigid block is suspended by the three springs whose lower ends were originally at the same level. Each steel spring has 24 turns of 5-mm-radius on a mean diameter of 100 mm, and G = 83 GPa. The bronze spring has 48 turns of 10-mm-radius wire on a mean diameter of 150 mm, and G = 42 GPa. Compute the maximum shearing stress in each spring. Phosphor Bronaw Stel 2m 50 kg 1m