The 500 N load is acting on the helical compression spring with 20 number of turns. The helical spring is having the mean diameter of 12cm.spring wire diameter is 6mm. Find the spring inside diameter. Select one: O a. 114 mm O b. 52mm O c. 150mm O d. 20mm

The 500 N load is acting on the helical compression spring with 20 number of turns. The helical spring is having the mean diameter of 12cm.spring wire diameter is 6mm. Find the spring inside diameter. Select one: O a. 114 mm O b. 52mm O c. 150mm O d. 20mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Related questions

Q: The shear strain is calculated using the torque and the polar moment of inertia.

A: In the given statement it is asked wheather shear strain is calculated using torque and polar moment…

Q: 2: A shaft runs at 100 r.p.m. and drives another shaft at 150 r.p.m. thi drive. The diameter of the…

Q: The smaller of two concentric spring is made of 22mm diameter steel & has an outside diameter of…

Q: The outer diameter of the shaft is 100 mm and the diameter ratio is 1.25. Find the polar modulus of…

A: Outer diameter/ Inner diameter = 1.25.

Q: Question 28 Compression coil spring is subjected to load of 500 N is having the mean diameter of 65…

A: For solution refer below images.

Q: A safety valve spring having 9 and 2 coils has the ends squared and ground. The outside diameter of…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: We are given the vertical cantilever of Fig. 1, which is subjected to a horizontal distributed load…

Q: A typical compound helical spring consists of two coaxial closed coil spring having the following…

Q: The smaller of two concentric helical spring is made of 22mm diameter steel spring and has an…

Q: A hollow steel shaft, 500 mm outside diameter and 300 mm inside diameter, has a coupling 80 mm thick…

A: Given data: Outside diameter of hollow shaft = 500 mm Inside diameter of hollow…

Q: 1.24 Find the length of the equivalent uniform hollow shaft of inner diameter d and thickness / that…

A: Solution: here l2 is the hallow shaft solid conical shaft length 'l' is show in…

Q: A spring with a squared and ground end has a pitch of 20mm and a wirediameter of 12.5mm. If there…

A: Given data P=20mm Diameter=12.5mm Number of coil=12 We have to determine the deflection of the…

Q: Determine the equiv. stiffness for the system mown in Figure (2) as measured at the mass m.

Q: Question 5 A crank arm consists of a sold segment of length bi and diameter d, a segment of length…

A: Apply force equilibrium condition along x direction.

Q: Find the size of 14 bolts required for C.I.steam engine cylinder head. The diameter of the cylinder…

A: Given data: Number of bolts (n) = 14 Diameter of the cylinder (d) = 400 mm Steam pressure (p) = 0.12…

Q: The crankpin of an engine sustains a maximum load of 35 kN due to steam pressure. If the allowable…

Q: For the pulley shown in the figure, determine the diameter of the four similar bolts needed to…

A: Assumptionsmaterial of bolt be 45C8Syt=380N/mm2now torque transmitted by pulley…

Q: Question 1 Consider the special steel spring in the illustration. 1) Find the pitch, solid height,…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: Rod AB is connected to the wall through hinge at A, and a chord connects the wall too fróm C (wall)…

Q: Steel bar in shape, AAB 600 mm and ABc = DACD3D 1200 mm2 are made of two stages. Determine the…

Q: A spring sustains 200 ft-lb of energy with a deflection of 3’’. Assume that the mean coil diameter…

Q: 8. Refer to figure 9. Given the following information: angles 0r= 20°, 02= 30°, 03= 41°, a 200 N…

Q: 3 m 4 m 1.5 m IB A 4 m 4 kN D

Q: (5) A gas engine valve spring is loaded to 35kg, when the valve is closed & 52kg, hen the valve is…

Q: he smaller of two concentric spring is made of 22mm diameter steel & has an outside diameter of 00mm…

Q: The rear spring of an automobile has 9 leaves, each with an average thickness of 0 and a width of 2…

A: t=0.242inb=2inL=56intotal weight=1300lb To-Find:- a) Rate of the springb) Maximum stress caused by…

Q: helical spring composed of 20 turns is fabricated by wrapping wire 20 mm in diameter around a…

A: Given data: n=20d=20 mmD=180 mmδ=105 mmτ=80 MPaG=83 GPa Need to determine the maximum load.

Q: A solid circular drive shaft connects a motor to gears B and C. The drive shaft is steel (G= 66 GPa)…

Q: Q1-1) See Figure 1, classify each of the structures as statically determinate, statically…

Q: 1. Find the effective stiffness (ke) of the spring system shown below. m -WW.

Q: For the same question, the M25 Screw will be used when pressing the Nut Wheel onto the shaft.…

A: Given: The screw base diameter, d = 21.5 mm The load need to compress, F = 1218 kgf Nut surface…

Q: IN THE SYSTEM SHOWN AS BELOW, A FORCE OF 200 N AFFECTS ON THE PIPE SWITCH. CONSISTING AT POINTS A…

A: Consider the Free body Diagram:

Q: An 8 in-diameter air compressor is operating with a maximum pressure of 10 psi. The bolts have a…

Q: Inside a helical sping of circulal cros section 20mm spring in diareteu. another is placed having…

A: Springs are one of the flexible machine elements, which gets deformed when load is applied to it and…

Q: A helical spring, having square and ground ends has a total of 20 coils and its material has a…

Q: Determine the minimum force required to deflect the spring with spring constant of 251 N/mm to a…

Q: spring system given in Figure Create the element matrices as well as the global stiffness and force…

Q: The outer diameter of the shaft is 175 mm and the diameter ratio is 1.25. Find the polar modulus of…

Q: he diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable tensile…

Q: Use the following shaft layout assuming a pulley transmits torque through a key and keyseat at…

Q: 1 N/mm, 495 N/mm, 541 N/mm respectively. Determine the equivalent spring constant if the springs are…

A: given:k1=641N/mmk2=495N/mmk3=541N/mm

Q: 5.3 A helical spring is made of 12-mm-diameter steel wire by winding it on a 120- mm-diameter…

A: Given data: Wire diameter(d)= 12mm Diameter of manderal (Di)= 120mm Mean radius(R) =120+12/2 =66mm…

Q: find the displacements at the inner radius of a long cylinder of inside diameter 80mm and outside…

Q: A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open.…

Q: 3. The free length of the plain ends spring is equal to (where: Na = the number of active coils, P =…

Q: A helical compression spring is used to absorb heavy vibrations. Apply mechanical engineering design…

Q: The smaller of two concentric helical springs is made of 22 mm diameter steel spring and has an…

A: Given data: di1=22 mmdo1=56 mmn1=10di2=32 mmdo2=250 mmn2=8 Need to determine the rate of each…

Q: Three extension springs are hooked in series and supports a weight of 70 kg. One spring has a rate…

A: Given Data Weight W = 70 Kg Spring rate for spring 1= 0.209 Kg/mm Spring rate for spring 2 and 3=…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

100%

The 500 N load is acting on the helical compression spring with 20 number of turns. The helical spring is having the mean diameter
of 12cm,spring wire diameter is 6mm. Find the spring inside diameter.
Select one:
O a. 114 mm
O b. 52mm
O c. 150mm
O d. 20mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

(8) The smaller of two concentric spring is made of 22mm diameter steel & has an outside diameter of 100mm with 10 active coils. The outer spring is made of 32mm steel spring & has an outside diameter 250mm with 8 active coils. Before the load is applied, the outer spring is 25mm longer than the inner spring. If the load of 90kN is applied to this nest of springs, (a) find the spring rate of each spring; (b) what portion of the total load is carried by each spring? Use G = 80GPa
Find the spring constant if a 20. N force stretches a spring 2.0 m.
The value of the spring index for a helical spring is 10. Calculate the outer diameter of the spring in mm if the mean diameter is 53 mm. O 69.96 O 5.30 O 58.30 O 49.55
Problem A 1) Find the equivalent spring,N/mm 2) Find the force, F KI K5 k k K2 x=10 mim k 00000 0000 k КЗ K4 K6 ....... ...... ...... ...... ........... .. ........
Need help. Please solve this and clearly state how you got your numbers and what formulas you used to solve it. Please make sure you find all the 6 unknows please. Knowing the beta equals 30° and the solid plate weigh 100 kg. What is the cable tension T and the reaction forces at the two bearings? Assume bearing A is a thrust bearing but bearing B is notplease solve for the X component at bearing B. Again please also make you find all the 6 unknows please. And clearly indicate which is which. And please label and make sure to put units
The value of the spring index for a helical spring is 14. Calculate the outer diameter of the spring in mm if the mean diameter is 40 mm. choose one 51.43 36.43 42.86 2.86
if the value of spring index is 9 and the mean diameter of the spring is 24 mm, the spring wire diameter d is ** . mm O a. 33.00 O b. 216.00 O c. 1.33 O d. 2.67
Use the drawing below to answer the following two questions. a. Determine the equivalent spring stiffness of the following system. Simplify the expression (ie – single common denominator. Your answer should be an expression of just K’s – no numbers). b. If the weight on top is 20 lb and the K1 = K4 = 50 lb/in, K2 = 33 lb/in and K3 = K5 = 25 lb/in, what is the natural frequency of the system?
Q1: The arrangement of a transmission brake is shown in the figure. The arms are pivoted at O and, when force is applied at the end of the hand lever, the screw AB will rotate. The left-and right- hand threads working in nuts on the ends of the arms will move the arms together and thus apply the brake actuating force equally. A B 12cm The drum is 17.75cm diameter, and the angle subtended by each block is 90°. the friction material lining width is 4cm. Assuming a coefficient of friction for the braking surfaces that is equal to 0.30 Determine the force required by the screw AB to set the brake torque on the drum equal to 200 N-m. 17 75cm 12cm 46 35cm Torqueleft= TorqueRight= 97.40 N.m 6 35cm 102.60 N.m
thick lnange be! The total torque required to turn the double threaded power screw is 55 N.m. If the screw turns at 285 rpm and the pitch of 4mm, find: A. The horsepower input of the power screw. B. The efficiency if the weight loaded is 10 kN.
The crane arm in the figure lifts the 95 kg mass at the end. When the angle BC piston makes with the horizontal is at the position 8= 0°, which of the following is the force acting on the BC piston in N? 785 mm 340 110 mm mm 360 mm Lütfen birini seçin: a. 3248.83 b. 4241.51 C. 6107.74 d. 2214.24
The spring Total stress is calculated by the which one of the relation. Select one: O a. Torsional shear stress+ direct shear stress O b. Torsional shear stress/ direct shear stress Torsional shear stress- direct shear stress O d. Direct shear stress/ Torsional shear stress.