Two stacked blocks are pushed along a horizontal table. Force F' is applied horizontally to the 6m block as shown: 5m 6m Assume there is kinetic friction at the interface between the 6m block and the table, and static friction at the interface between the two blocks. If m = 8 kg, μ = 0.56, and 0.15, what is the maximum force F' that can be exerted withou the top block slipping? Express your answer in N, to at least one digit after the decimal point.

Two stacked blocks are pushed along a horizontal table. Force F' is applied horizontally to the 6m block as shown: 5m 6m Assume there is kinetic friction at the interface between the 6m block and the table, and static friction at the interface between the two blocks. If m = 8 kg, μ = 0.56, and 0.15, what is the maximum force F' that can be exerted withou the top block slipping? Express your answer in N, to at least one digit after the decimal point.

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter5: Displacement And Force In Two Dimensions

Section: Chapter Questions

Problem 82A

See similar textbooks

Similar questions

Jamal and Dayo are lifting a large chest, weighing 207 lb, by using the two rope handles attached to either side. As they lift and hold it up so that it is motionless, each handle makes a different angle with respect to the vertical side of the chest (Fig. P5.76). If the angle between Jamals handle and the vertical side is 25.0 and the angle between Dayos handle and the vertical side of the chest is 30.0, what are the tensions in each handle? FIGURE P5.76
I 00LLJ408 - Go.. Question Info and Solutions Blocks A and B of mass 5 kg and 10 kg respectively are placed on a Smooth inclined plane of Inclination 30, as shown. Block A and B are subjected to forces 5 N And 50 N respectively along the incline, as shown. The coefficient of friction between A andBis 0.50 find the frictional force between A and B in N is: (g= 10 ms SOH 300 Options Solution Fs=Static frictional force umg cos 30 (0.5) (5) (10) cos 30 21.6 N Let a be the acceleration of both the blocks along 5.27 PM
A manual roller of weight mg = 337.5 N is pushed with a force 182.8N at an angle 0, such that sin(e) = 0.4, with the horizontal direction. What is the force exerted by the floor on the box? F cose F sine mg
The static friction coefficient between the block and the inclined surface is 0.2. What is the minimum force that should be applied to the block perpendicular the surface in order to prevent the block from sliding down?
The 6-m pole ABC is acted upon by a 460-N force, P, as shown in the figure. The pole is held by a ball-and-socket joint at A and by two cables BD and BE. For a = 3 m, determine the tension in each cable and the reaction at A. (Round the final answers to one decimal place.) 3. 1.5 m P E The tension in cable BD is The tension in cable BE is The reaction at A is - ( y C B 3 m N. N. N)i + 3 m 3 m 1.5 m 3 m X N)j + N)k.
Problem A block of mass m is placed on a rough surface inclined relative to the horizontal. The incline angle is increased until the block start to move. Show that you can obtain the coefficient of static friction ug by measuring the critical angle 0 where slipping occurs. mg pino to .... my 18.
1 m A 10.3 m D B Figure 5
A block of mass m is placed on a rough surface inclined relative to the horizontal. The incline angle is increased until the block start to move. Show that you can obtain the coefficient of static friction Hs by measuring the critical angle e where slipping occurs. Problem mg pin to Solution Just before slipping, we say that the block is still at rest, so the net force on the x-axis is: ZFx=mg Evaluating, we get: = mg
The weight of the box is W = 90 N and the coefficient of static friction between the box and the floor is μ=0.65. Neglect the weights of the bars. What is the largest value of the force F that will not cause the box to slip?
MY NOTES ASK YOU Consider the figure below. (Let w, = 130 N and w, = 55.0 N.) W, W2 (a) What is the minimum force of friction required to hold the system of the figure above in equilibrium? (b) What coefficient of static friction between the 130-N block and the table ensures equilibrium? (Enter the minimum acceptable coefficient of friction.) (c) If the coefficient of kinetic friction between the 130-N block and the table is 0.212, what hanging weight should replace the 55.0-N weight to allow the system to mc constant speed once it is set in motion?
Ed and Al are pushing on a couch as shown in the picture and it doesn't slip. EC Ec Ed is pushing with a force of 362.8 N at an angle of 0 = 50.3 degrees with respect to the vertical and Al is pushing with a force of 126.8 N at an angle of o = 29 degrees with respect to the horizontal. If the couch has a mass of 98 kg and the coefficients of static and kinetic friction between the couch and the floor are ug = 0.52, and u = 0.39, what is the magnitude of the force of friction exerted by the floor on the couch? Click here for a hint F =
A typical jar that has been tightened to a reasonable degree requires 2.0 N ⋅ m to open. If you grab a 7.0-cm-diameter jar lid with one hand so that your thumb and fingers exert equal magnitude forces on opposite sides of the lid, as shown, what is the magnitude of each of the forces?