Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. The diameter of rod (1) is d₁ = 18 mm and the diameter of rod (2) is d₂ = 31 mm. Determine the absolute value of the normal stress in rod (2). 140 KN 80 KN (2) 140 KN (1) A O 342 MPa O 368 MPa O 313 MPa 0281 MP₂ B

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. The diameter of rod (1) is d₁ = 18 mm and the diameter of rod (2) is d₂ = 31 mm. Determine the absolute value of the normal stress in rod (2). 140 KN 80 KN (2) 140 KN (1) A O 342 MPa O 368 MPa O 313 MPa 0281 MP₂ B

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Similar questions

-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. The diameter of rod (1) is d₁ = 23 mm and the diameter of rod (2) is d2 = 34 mm. Determine the absolute value of the normal stress in rod (2). 80 KN d₁ 232 MPa 255 MPa 305 MPa O 160 MPa O 220 MPa 140 KN 140 KN B
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the normal stress in each rod must be limited to 105 MPa, determine the minimum diameter d₂ required for rod (2). d₂ d₁ 140 KN 80 KN 140 KN A ↑ 31.5 mm 40.1 mm 36.7 mm 49.2 mm 44.9 mm 'В
Determine the state of stress acting at point D. Take P₁ = 120 kN and P₂ = 45 kN. (Figure 1) Figure L -1.5m- +1.5m-1.5 m- 0.5 m 40 mm 100 mm 60 mm 80 mm 1 of 1 > Find op- Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. od= - 154.88 Submit Part B Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining MPa Find TD- Express your answer to three significant figures and include the appropriate units. JA TD= Value Units ?
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. The diameter of rod (1) is d₁ = 16 mm and the diameter of rod (2) is d₂ = 33 mm. Determine the absolute value of the normal stress in rod (2). d₂ d₁ 140 KN 80 KN 140 KN A ↑ 304 MPa 218 MPa 270 MPa 234 MPa 328 MPa 'В
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 13 kips, F₂ = 34 kips, and the normal stress in each rod must be limited to 22 ksi, determine the minimum diameter d₁ required for rod (1). A (2) d₁ F₂ B C O 1.087 in. O 0.823 in. O 0.541 in. O 0.867 in. O 1.003 in. d₂
1. The strut is supported by a pin at C and a steel guy wire AB. The wire AB has a diameter of 0.2 in. The maximum normal stress that the steel in the wire can withstand is omax = 18 ksi. Will the wire fail? Show your work and your reasoning. 60 200 lb/ft B 9 ft
Determine the maximum value of the force P (kN) that can be applied to member AD if the allowable stress is 200 MPa, and the maximum upward displacement of point A is 3 mm. Use E=100 GPa. Cross-sectional area (mm?) L1 (m) L2 (m) L3 (m) 270 3.8 2.2 0.85 (Ctrl) P A L1 B. 12 kN L2 9 kN L3
The distribution of stress in an isotropic aluminium machine component is given (in MPa) as: σ₂ = y +2z² - 6 σ₁ = x+z-6 oy σ₂ = 3x+y-13 6: T =3z² -11 xy (i) (ii) =x²-14 Tyz Txz = y² XZ x, y and z are coordinates of a point within the machine component. By taking Young's modulus, E = 70 GPa, Poisson ratio, v= 0.3 and yield stress, Y = 5 MPa, do the following for a point P located at (4, 1, 2): a) Provide the stress and strain tensors. b) Determine all the principal stresses and principal strains. c) Determine if the machine component will fail based on the failure criteria below: Tresca criterion Von Mises criterion
Calculate the combined stress (MPa) on the rod shown below using the principle stress method. Here, F1 = 0.35 kN, F2 = 0.12 kN, T = 428000 N-mm. Length and diameter of the rod are 75 cm and 75 mm, respectively. F2 F1 d
3. An axial pull of 35000 N is acting on a bar consisting of three lengths as shown below. If the Young's Modulus is 2.1 x 105 N/mm2. Determine (i) Stresses in each section, and; (ii) Total extension of the bar. Section 3 Section 2 Section 1 35000 N 35000 N 2 cm DIA 3 cm DIA 5 cm DIA k-20 cm- 25 cm -22 cm-
The collar bearing shown is subject to a 500 kN force. 500 kN The collar is 25 mm thick. Find d and D (to the nearest mm) so that the allowable normal stress in the column collar bearing of o = 280 MPa, the allowable shear stress in the collar collar of t = 200 MPa and the allowable bearing stress between the collar and the support of ob = 70 MPa is not exceeded.